P5A-CB0001Wireless Mouse

Mouse Receiver Introduction Congratulations on your purchase of the most innovative wireless mini mouse. With an incredible sensitivity to surface details and high tracking speed than other mice, the mouse can track reliably even on tricky polished or wood-grain surfaces. It of fers even more advance that will make you more productive and more comfortable. 1. Insert the batteries a. Take out the receiver on the bottom case first, press the battery cover release button on the bottom of the mouse which is under the receiver. b. Remove the battery compartment cover on the top case of the mouse. c. Fit in the batteries accordingly to the diagram indicated in the battery cabinet. d. Close the battery compartments cover properly. e. Make sure the Power on-off swich on the bottom of the mouse is ON. f. The Low Power LED in the wheel bar will light up 3 seconds if the mouse. A. Hardware Installation A wrong battery placement may cause batteries overheat. The unit of fers a strong power saving management. Once the mouse accesses the sleeping mode, " to click any button of the mouse" is compulsory to wake it up. Power on/off: There is a Power on/off switch designed to save the batteries power while non-usage of a longer period. Users can push DPI button to change the resolution. The LED on scroll wheel will be flashed when dpi has been successfully swithced. 4. Replace the new batteries Please replace a pair of new batteries and follow the previous instructions. (2, 3) The red LED on the scroll wheel is the low batteries power indicator. It indicates that batteries inside the mouse are needed to be replaced. Note 5. Operation 4-Way Scrolling: a. Vertical Scrolling Roll wheel up to scroll up; roll wheel down to scroll down. b. Horizontal Scrolling Hold the wheel to left to scroll left; hold the wheel to right to scroll right. Release wheel to stop scrolling function. Press ID reset button Execute ID connection software Led indicator blinks faster 1 23 4 ID links OK! While the mouse is working, if encountering any interference, the mouse and the receiver will automatically source out and transfer to another free channel. During the transferring, the cursor movement may have a second delay. Note 3. Communication : The mouse & the receiver The 2.4Ghz RF mouse features a dual-way transmission technology which enables the mouse and the receiver auto-communication. A. Auto-link mode 1. Make sure the Power on-off Switch on the bottom of the mouse is ON. 2. Operate the mouse, and the LED in the receiver will blink fast. Now the mouse and the receiver is auto-linked successfully. B. Manual mode If you find the communication channel does not connect well, you can use the software connection tool to re-connect the mouse & receiver to reset a new channel ID. You are able to get the software from the included diskette of the package or download from your local brand vendor's website. LED Wheel button/Low power Led/ Dpi switching indicator Dpi button Battery cover ID reset button Receiver Receiver release button 2.4GHz (distance 6~8m), 16 Channels/4096 ID Using state-of-art technology. High tracking speed and sensitivity. 4-way scrolling. Storable mini receiver Longer battery life -- 3~4 months. Auto-Link, Plug and Play! No need to set the channel ID. Power on/off switch Data report rate : 125 Report/Sec. 800/1600 dpi switchable button. 2*AAA Alkaline batteries included. Power on/off switch Features Battery cover release button + - Battery compartment cover 2 * AAA batteries Battery cover release button 2. Connect the receiver a. Turn on your PC. b. Connect the receivere to USB port on PC PC USB port B. Driver Installation The mouse features plug & play. It is not necessary to install the driver to operate the mouse. The driver is an optional item included. However if the model purchased is with 4-Way Scrolling function, you may require the mouse software driver to make the 4-Way scrolling function ef fective. The 4-Way scrolling function is only effective under successful installation of the original mouse driver. The driver is an optional item included in the package or it can be downloaded from the website of your local brand vendor. To function the 4-way scrolling in some applications in Window VISTA such as Word, Excel, Powerpoint and etc., the driver should be installed. Note

Project No.: 0801C030 Page 2 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 2 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 3 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 3 of 10 Neutron Engineering Inc. 0801C030 0801C030

Optical Optical Wireless Mouse B158 C23 16mm 28.4mm 9.8mm 19mm FCC ID: P5A-CB0001 FCC ID: P5A-CB0001

Project No.: 0801C030 Page 4 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 4 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 5 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 5 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 6 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 6 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 7 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 7 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 8 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 8 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 9 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 9 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 10 of 10 Neutron Engineering Inc. 0801C030 0801C030 Project No.: 0801C030 Page 10 of 10 Neutron Engineering Inc. 0801C030 0801C030

Report No.: NEI-FCCP-1-0801C030 Page 2 of 47 Neutron Engineering Inc. Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCCP-1-0801C030 Page 3 of 47 Neutron Engineering Inc. Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.4 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 15 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 17 4.2.1 RADIATED EMISSION LIMITS 17 4.2.2 MEASUREMENT INSTRUMENTS LIST 18 4.2.3 TEST PROCEDURE 19 4.2.4 DEVIATION FROM TEST STANDARD 19 4.2.5 TEST SETUP 20 4.2.6 EUT OPERATING CONDITIONS 20 4.2.7 TEST RESULTS (BETWEEN 30 – 1000 MHz) 21 4.2.8 TEST RESULTS (ABOVE 1000 MHz) 23 4.2.9 TEST RESULTS (2400 – 2483.5 MHz) 35 4.2.10 TEST RESULTS (Restricted Bands Requirements) 36 5 . BANDWIDTH TEST 40 5.1 MEASUREMENT INSTRUMENTS LIST 40 5.2 TEST PROCEDURE 40 5.3 DEVIATION FROM STANDARD 40 5.4 TEST SETUP 40 5.5 EUT OPERATION CONDITIONS 40 5.6 TEST RESULTS 41 Report No.: NEI-FCCP-1-0801C030 Page 4 of 47 Neutron Engineering Inc. Table of Contents Page 6 . ANTENNA CONDUCTED SPURIOUS EMISSION 43 6.1 APPLIED PROCEDURES / LIMIT 43 6.1.1 MEASUREMENT INSTRUMENTS LIST 43 6.1.2 TEST PROCEDURE 43 6.1.3 DEVIATION FROM STANDARD 43 6.1.4 TEST SETUP 43 6.1.5 EUT OPERATION CONDITIONS 44 6.1.6 TEST RESULTS 45 7 . EUT TEST PHOTO 47 Report No.: NEI-FCCP-1-0801C030 Page 5 of 47 Neutron Engineering Inc. 1. CERTIFICATION Equipment : Wireless Mouse Trade Name : N/A Model Name. : B158;IVR-61020 A p p l i c a n t : A reson Technology Corporation Date of Test : Jan. 08, 2008~ Jan. 25, 2008 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.249)/ ANCI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-0801C030) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: NEI-FCCP-1-0801C030 Page 6 of 47 Neutron Engineering Inc. 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.249) Standard Section Test Item Judgment Remark 15.207 Conducted Emission - N/A 15.249 Radiated Spurious Emission PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Report No.: NEI-FCCP-1-0801C030 Page 7 of 47 Neutron Engineering Inc. 2.1 TEST FACILITY The test facilities used to collect the test data in this report is C01/OS02 at the location of No.132-1, Lane 329, Sec. 2, Palain Road, Shijr City, Taipei, Taiwan. Neutron's test firm number is 95335 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE C01 ANSI150 KHz ~ 30MHz 1.94 B. Radiated Measurement : Test Site Method Measurement Frequency Range Ant. H / V U，(dB) NOTE OS-01 ANSI30MHz ~ 200MHz V 3.82 30MHz ~ 200MHz H 3.60 200MHz ~ 1,000MHz V 3.86 200MHz ~ 1,000MHz H 3.94 OS-02 ANSI30MHz ~ 200MHz V 2.48 30MHz ~ 200MHz H 2.16 200MHz ~ 1,000MHz V 2.50 200MHz ~ 1,000MHz H 2.66 Report No.: NEI-FCCP-1-0801C030 Page 8 of 47 Neutron Engineering Inc. 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Wireless Mouse Trade Name N/A Model Name. B158;IVR-61020 OEM Brand/Model Name N/A Model Difference This product is defined two different names, but they are in fact the same product. Product Description The EUT is a Wireless Mouse. Product Type Low Power Communication Device Operation Frequency: 2402~2479 MHz Modulation Type: GFSK Number Of Channel 16CH Antenna Designation: Printed antenna Antenna Gain(Peak) -0.98 dBi (Mouse) Output Power: 51.77 dBuV/m (AV Max.) Based on the application, features, or specification exhibited in User's Manual, the EUT is consi…

Text truncated - open the document above for the full version.

Report No.: NEI-FCCP-1-0801C030 Page 47 of 47 Neutron Engineering Inc. Radiated Measurement Photos TX Mode Report No.: NEI-FCCP-1-0801C030 Page 47 of 47 Neutron Engineering Inc. Radiated Measurement Photos TX Mode