P5A-CB00172.4GHz Wireless mouse

User's Guide Wireless Optical Virtual Touch Mouse B8021MR + C75 ◎ Battery use reminders ◎ Trouble Shooting FCC statement Important Notes:  Please follow the instructions contained in the manual. Do not try to disassemble or replace parts in the products.  Do not put the product in water or on any wet surfaces.  To avoid electrocution, please do not pick up the device when your hands are wet.  Do not put the product near a heat source. 1. Remove worn-out batteries from equipment immediately and dispose of them promptly 2. Keep all batteries (used or new) out of the reach of children. 3. Never dispose of batteries in fire, as they could explode. 4. Always replace all the batteries at the same time. Mixing old and new batteries or mining types (such as alkaline with zinc carbon) will reduce overall performance and could cause leakage or rupture. 5. Do not mix different types of batteries (e.g. Ni MH, NiCd, alkaline, and etc) in the mouse. 6. Remove batteries from this device if the device is not going to be used for a long time. 7. If the performance of the batteries decreases substantially, it is time to replace the batteries. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Note : Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. a. Make sure you have connected the receiver correctly to the computer's USB port. b. Check if the batteries have been installed correctly according to the diagram indicated in the battery cabinet c. For the best performance, we suggest that you place the receiver away from other electrical devices. d. Unplug and re-plug the receiver, or try another USB port. Try connecting directly to your computer instead of using a USB hub. A wrong battery placement may cause batteries overheat. + - Battery compartment cover 2 * AAA batteries Receiver Wheel button Power on/off switch Receiver Battery cover Mode button Mouse Internet Forward & Backward button LED indicator Features Benefits of Virtual Touch Mouse Introduction A. Hardware Installation 1. Insert the batteries System Requirements a. Remove the battery cover and insert new batteries. b. Move the power switch to the ON position. c. The Low Power red LED on the left side will be on for 6 seconds after the mouse power is switched to on. 2. Connect the receiver 1. Installation a. Turn on your PC. b. Connect the receiver to the USB port on PC. c. Please wait for a while for the PC to detect the receiver device. (The waiting time depends on PC hardware.) Congratulations on your purchase of the most innovative mouse, “Virtual Touch mouse”. The Virtual Touch mouse features and integrates the advantages of the patented technology of traditional mouse and the up-to-date touch screen technology, enabling users to operate touch screen functions on Windows 8 by just mouse button click and mouse move- ment, without fingers touching on screen. It is designed to make you more productive and more comfortable. 2.4G Hz (distance 6~8m), 34 Channels 2 24 ID Patented and state-of-art emulating touch screen technology 2-in-1 design : a traditional mouse with touch screen functions for Windows 8 To emulate touch screen behaviors by just mouse button click and mouse movement. Two switchable modes: 1. standard mouse mode ----- for traditional mouse functions 2. Virtual-Touch mode ----- to emulate touch screen functions, with the Virtual Touch Driver installed. Longer battery life 800/1600 dpi switchable (simultaneously press the middle button and right button for 3 seconds to change dpi), default at 1600dpi To relieve hands fatigue from arm arising and finger touching on screen. To achieve the same functions of touch screen without finger touching on the screen. To operate the touch screen functions in a remote distance. Desktop and Notebook users can also experience the touch screen functions even with a non-touch screen monitor. To keep screen always clean. No need to touch the screen with finger tips. For standard mouse mode : Windows XP/Vista/7/8, and Mac OS 10.6 or higher For Virtual Touch mouse mode: Windows 8 only. [Not available for Windows RT] USB Port PC USB port Pull out the receiver B. Software Installations To activate the Virtual Touch mode functions, please insert the accompanied CD into your computer, or download the Virtual Touch Driver from your local brand vendor's website. 4. Low Power Indicator : Red LED If the battery power is low, the Red LED as the low power indicator will blink for six seconds when the mouse is back to start working. Virtual Touch Mode Mode button C. LED Indicators 3. Power On Indicator : Red LED When batteries are installed or power is switched to on, t…

Text truncated - open the document above for the full version.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group LAB CODE 20050712-00 Report No.: EO/2012/30034 IssuedDate:April27, 2012 Page :1of9 AntennaTest Report Report No.: EO/2012/30034 Test Plan: Non-compliance with ISO17025 Applicant Name: ARESON Technology Corp. Manufacturer Name:Dong Guan Hong Sheng Electronic Corp. Product Name:2.4GHz Wireless mouse Model Number:Meadline type antenna4 Measurements performed at SGSTaiwan Ltd. Taipei, Taiwan Issued Date:April27, 2012 NameDate & SignatureDistribution Prepared by: Dragon Wu Supervisor April 27, 2012 Approved by: Nick Hsu Supervisor April 27, 2012 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group LAB CODE 20050712-00 Report No.:EO/2012/30034 Page No.:2 of9 Measurement System Information General Information Testing Condition: Temperature: 22±3 ̊C Humidity: <80% Measurement Facility: Measurement Chamber: Satimo3D fully anechoic chamber and its measuring system (Stargate-24) Base Station Simulator:CMU200(orAgilent E5515C) Network Analyzer: Agilent E5071C Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group LAB CODE 20050712-00 Report No.:EO/2012/30034 Page No.:3 of9 Measurements are performed in a SatimoStargate-24with the StarAct interface for a base station simulator. TheStargate-24has 23 probe antennas mounted with equal spacing on a circular arch. Electronic switching of the probe antennas provides outstanding measurement speed. The geometry of the setup, with only a Styrofoam column within 1.2 meters of the EUT, ensures minimum interference and low ripple on the measured radiation patterns.The DUT is placed on top of the pedestal, in the center of the system. Typical Setup for Satimo Stargate-24: Instruments ViewInside View Unless otherwise stated…

Text truncated - open the document above for the full version.

Front View of EUT Back View of EUT Side View of EUT - 1 Side View of EUT - 2 Side View of EUT - 3 Side View of EUT - 4

Optical Wireless Mouse S/N:YYMM000001 The device complies with part 15 of the FCC rules. ARESON B8021MR FCC ID : P5A-CB0017

Open View of EUT Internal View of EUT-1 Internal View of EUT-2 Internal View of EUT-3 Internal View of EUT-4 Internal View of EUT-5 2.4GHz Antenna

Report No.: E2/2013/80030 FCC ID: P5A-CB0017 Issue Date: Oct 01, 2013 Page 1 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: 2.4GHz Wireless mouse Brand Name: N/A Model No.: B8021MR Model Difference: N/A FCC ID: P5A-CB0017 Report No.: E2/2013/80030 Issue Date: Oct. 01, 2013 FCC Rule Part: §15.249 Prepared for: ARESON Technology Corp. 11F, No. 646, Sec. 5, Chongxin Rd., Sanchung Dist.,New Taipei City 241,Taiwan (R.O.C.) Prepared by: SGS Taiwan Ltd. Electronics & Communication Laboratory No.2, Keji 1st Rd., Guishan Township, Taoyuan County, Taiwan 333 Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. Report No.: E2/2013/80030 FCC ID: P5A-CB0017 Issue Date: Oct 01, 2013 Page 2 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group VERIFICATION OF COMPLIANCE Applicant: ARESON Technology Corp. 11F, No. 646, Sec. 5, Chongxin Rd., Sanchung Dist.,New Taipei City 241,Taiwan (R.O.C.) Product Description: 2.4GHz Wireless Dongle FCC ID: P5A-CB0017 Brand Name: N/A Model No.: B8021MR Model Difference: N/A File Number: E2/2013/80030 Date of test: Sep. 03, 2013 ~ Oct. 01, 2013 Date of EUT Received: Sep. 03, 2013 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd., Electronics & Communication Laboratory. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.249. The test results of this report relate only to the tested sample identified in this report. Test By: Date: Oct. 01, 2013 Jazz Huang / Engineer Prepared By: Date: Oct. 01, 2013 Julia Chang / Clerk Approved By: Date: Oct. 01, 2013 Jim Chang / Supervisor Report No.: E2/2013/80030 FCC ID: P5A-CB0017 Issue Date: Oct 01, 2013 Page 3 of 30 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document …

Text truncated - open the document above for the full version.

Radiated Emission Setup Photos (E2 Plane)