P68MT7000Motor Trend Bluetooth Headset

Turn On Switch the on/off Button to ON position, it will turn ON the headset and flash blue. Turn Off Switch the on/off Button to OFF position, it will turn OFF the headset and flash red 3 times. 2 Index 1.Notice before Using 2.Package Contents 3.Functional Parts 4.Charging the Headset 5.Power On / Off 6.Pairing the Headset with a Bluetooth Device 7.Operation Guide 8.Low Battery Prompt 9.Specifications 10.Safety Instructions 11.Question and Answers 12.Declaration of Conformity 13.Limited Warranty 1 2.Package Contents: Before using the headset for the first time, be sure and fully charge the unit at least 4 hours, preferably overnight (8-10 hours) 3 The MT-7000 comes with a built in Lithium Polymer battery. To charge the unit: a)Plug the travel charger into an electrical outlet b)Plug the unit end of the travel charger into the power interface adaptor c)While charging, the LED Indicator Light will flash red then stay lit. If the battery level is high, the LED will be Blue. 4 ·For first time use, make sure to fully charge the headset at least 4 hours, preferably overnight (8-10 hours) ·If headset has not been used for more than 21 days, when recharging it please charge the unit at least 4 hours, preferably overnight (8-10 hours) as the battery will need a full charge and be aware the LED Indicator light may take several hours to show recharging is complete. ·While charging the unit, do not use the headset ·Use original charger included with the headset to charge / recharge the unit ·When the LED indicator light flashes red during usage or while on standby, the battery is low and you should recharge the unit as soon as possible. ·While turning on the headset, you will hear “Du Du” prompt from the receiver. The blue indicator light will flash 5 times, then 2 times, and after repeating this for 5 cycles the indicator light will flash the blue light every 3 seconds until the unit adjusts into standby mode. ·While the headset is turned on, it will automatically search for the paired device. Under the ON mode and within the effective range of 30 feet from the headset, the indicator will flash the blue light to indicate that it entered the connecting mode. ·When turning the headset off, you will hear “Du” sound, then the indicator will shut off after flashing the red light a few times. 5 Once the mobile phone is paired with the headset, there is no further pairing action required. As long as the Bluetooth function on the mobile phone is activated and the headset is on, they will recognize each other and they will be automatically connected. When the battery power gets low, the red LED will flash and there will be a short tone from the headset. If the battery power continues to decrease, the headset will switch off automatically. 9.Specifications: ·If the headset LED indicator light is flashing red the battery is low and recharge the unit immediately ·If, after recharging for 20 minutes, the headset does not turn on: For initial use, the power will be on after charging the headset at least 40 minutes. The manufacturers recommended initial charging time is no less than 4 hours. Q: Why does the fully charged headset under the ON mode not work with my Bluetooth device? A: You must activate the Bluetooth function of the mobile device and complete the device pairing process between the device and the headset. Q: Can the MT-7000 work with any mobile device? A: No, Only Bluetooth enabled devices Q: How far is the working distance between the headset and the mobile device? CE: We, Premier Accessory Group, LLC. Declare under our sole responsibility that our product MT7000 and in combination with our accessories, to which this declaration relates, is in conformity with the appropriate standards, EN 301489,EN 300328, and EN 60950, following the provisions of Radio Equipment and Telecommunication Terminal Equipment directive 99/5/EC, with requirements covering EMC directive 89/336/EEC, and Low Voltage directive 73/23/EEC. ROHS: All Premier Accessory Group products are fully compliant with the ROHS Directive 2002/95/EC. WEEE: All Premier Accessory Group products are fully compliant with the WEEE Directive 2002/96/EC. This warranty covers defects in material and workmanships of Premier Accessory Group, LLC and their respective product divisions MOTOR TREND line of Bluetooth products manufactured and sold by Premier Accessory Group which were purchased and used in the United States or Canada. The warranty period is for 2 years from the date of purchase of the original product. -The entire headset including any charger that came as original to the headset. -If less than 7 days from purchase, please return the original packaging. -Provide information regarding the nature of the problem and the reason for return. -Provide your name, address and telephone number. -When returning product for warranty service, if purchase was made within the last 90 days, no additional Shipping and Handling is due to manufacturer for replacement product. -If product was purchased more than 90 days prior to return of product for Warranty Service, shipping and handling fee of 14.95 is due to manufacturer for replacement product. -Manufacturer is not responsible for lost headsets if mailed via first class mail without insurance or delivery confirmation. Return the product and Shipping and Handling Fee (when applicable) to the address below: Premier Accessory Group, LLC Attn: Customer Service Warranty (Toll Free 866-446-4327) 11-11 44th Drive Long Island City, N.Y. 11101 Legal Notice: This product is manufactured under license for Source Interlink Magazines, LLC, the publisher of MOTOR TREND Magazine and a Source Interlink Media company. Premier Accessory Group, LLC 2009 All Rights Reserved. U.S. & International patents, trademarks, copyrights and registrations issued and pending. The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. MOTOR TREND Bluetooth Headset User Guide MX6 Noise Canceling Techno…

Text truncated - open the document above for the full version.

R&D Manager Marion Z.

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT –Full View EUT – Front View EUT – Rear View EUT – Left SideView EUT – Right SideView EUT – Car ChargerView EUT –USB Cable View EUT – Adapter View EUT – Battery View

EXHIBIT A - FCC ID LABELING AND LOCATION Proposed FCC ID Labeling Proposed FCC ID Location Label here The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Cover offView 1 EUT – Cover offView 2 EUT – Main Board Top View EUT – Main Board BottomView Bluetooth Antenna EUT – Pairing Board Top View EUT – Pairing Board Bottom View

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 15.247 MEASUREMENT AND TEST REPORT For Audex Telecom Industrial Co., Ltd. 4/F., Chuangye Center, Kangle Road., Zhongshan Torch Hi-Tech Industrial Zone, Zhongshan, Guangdong, China Report Type: Original Report Product Type: Motor Trend Bluetooth Headset Test Engineer: Weir Zhong Report Number: RSZ10031101 Report Date: 2010-03-23 Reviewed By: Merry Zhao EMC Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 FCC ID: P68MT7000 Audex Telecom Industrial Co., Ltd. FCC ID: P68MT7000 Report No.: RSZ10031101 Page 2 of 42 FCC Part15.247 Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 DESCRIPTION OF TEST CONFIGURATION......................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 EUT EXERCISE SOFTWARE..........................................................................................................................................6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS........................................................................................................6 EXTERNAL I/O CABLE..................................................................................................................................................6 CONFIGURATION OF TEST SETUP.................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................7 SUMMARY OF TEST RESULTS...............................................................................................................................9 CFR47 §15.247 (i), §1.1307 (b)(1) & §2.1093 - RF EXPOSURE ..................................................................................10 STANDARD APPLICABLE............................................................................................................................................10 CFR47 §15.203 – ANTENNA REQUIREMENT......................................................................................................11 STANDARD APPLICABLE............................................................................................................................................11 ANTENNA CONNECTOR CONSTRUCTION....................................................................................................................11 CFR47 §15.207 (a) - CONDUCTED EMISSIONS ...................................................................................................12 APPLICABLE STANDARD............................................................................................................................................12 MEASUREMENT UNCERTAINTY..................................................................................................................................12 EUT SETUP................................................................................................................................................................12 EMI TEST RECEIVER SETUP.......................................................................................................................................13 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................13 TEST PROCEDURE......................................................................................................................................................13 TEST RESULTS SUMMARY..........................................................................................................................................13 TEST DATA................................................................................................................................................................13 CFR47 §15.205, §15.109, §15.209, §15.247 (d) – RADIATED EMISSIONS ..........................................................16 APPLICABLE STANDARD........................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Disturbance at Mains Terminals - Front View (Charging mode) Conducted Disturbance at Mains Terminals - Side View (Charging mode) Below 1GHz: Spurious Radiated Emissions - Front View (Transmitting mode) Below 1GHz: Spurious Radiated Emissions - Rear View (Transmitting mode) Below 1GHz: Spurious Radiated Emissions - Front View (Charging by AC adapter) Below 1GHz: Spurious Radiated Emissions - Rear View (Charging by AC adapter) Below 1GHz: Spurious Radiated Emissions - Front View (Charging by car charger adapter) Below 1GHz: Spurious Radiated Emissions - Rear View (Charging by car charger adapter) Above 1GHz: Spurious Radiated Emissions - Front View (Transmitting mode) Above 1GHz: Spurious Radiated Emissions - Rear View (Transmitting mode)