P6W001PIR Motion Detector

Model: WY-TXA01 FCC ID.: P6W001 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Trade Name: Weiyang Electric Wire & Cable Co., Ltd. Made in Taiwan

The principle description of the Window Sensor When the magnet is removed from the ‘Window Sensor’, the reed switch is skipped from NO to NC. Then the 12V power is supplied from C8 and C7 both to encoder (sm5023s) by way of the transmitter circuit. It will simultaneously generate a frequency of 315 MHz; and the window open will be shown on the screen.

FCC ID.:P6W001 Rev. No 1.0 FCC Part 15 Subpart C EMI TEST REPORT of E.U.T. : Magnetic Window Sensor FCC ID. : P6W001 MODEL : WY-TXA01 Working Frequency : 315 MHz for APPLICANT: Weiyang Electric Wire & Cable Co., Ltd. ADDRESS: 1-2F, NO. 6, Pao Kao Rd. Hsin Tien City, Taipei, 231 Taiwan, R.O.C. Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 8 LANE 29, WENMIMG ROAD, LOSHAN TSUN, KWEISHAN HSIANG, TAOYUAN, TAIWAN, R.O.C. Tel:(03)3276170-3276174 Fax:(03)3276188 Report Number : ET90S-12-159-03 ETC Report No.:ET90S-12-159-03FCC ID.: P6W001 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant: Weiyang Electric Wire & Cable Co., Ltd. 1-2F, NO. 6, Pao Kao Rd. Hsin Tien City, Taipei, 231 Taiwan, R.O.C. Manufacturer: Weiyang Electric Wire & Cable Co., Ltd. 1-2F, NO. 6, Pao Kao Rd. Hsin Tien City, Taipei, 231 Taiwan, R.O.C. Description of EUT: a) Type of EUT: Magnetic Window Sensor b) Trade Name: -- c) Model No.: WY-TXA01 d) FCC ID: P6W001 e) Working Frequency: 315 MHz f) Power Supply: DC 12V Battery Regulation Applied: FCC Rules and Regulations Part 15 Subpart C (2001) I HEREBY CERTIFY THAT; The data shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note : 1. The results of the testing report relate only to the items tested. 2. The testing report shall not be reproduced except in full, without the written approval of ETC. Test Date : Jan. 10, 2002 Test Engineer : Approve & Authorized Signer : Win-Po Tsai, Supervisor, NVLAP Signatory EMC Dept. I of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No.:ET90S-12-159-03FCC ID.: P6W001 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION............................................................................................................................................................1 1.1 PRODUCT DESCRIPTION...................................................................................................................................................................1 1.2 CHARACTERISTICS OF DEVICE:.......................................................................................................................................................1 1.3 TEST METHODOLOGY......................................................................................................................................................................1 1.4 TEST FACILITY..................................................................................................................................................................................1 2. DEFINITION AND LIMITS..............................................................................................................................................................2 2.1 DEFINITION........................................................................................................................................................................................2 2.2 RESTRICTED BANDS OF OPERATION.............................................................................................................................................2 2.3 LIMITATION.......................................................................................................................................................................................2 2.4 LABELING REQUIREMENT...............................................................................................................................................................4 2.5 USER INFORMATION.........................................................................................................................................................................4 3. RADIATED EMISSION MEASUREMENT....................................................................................................................................5 3.1 APPLICABLE STANDARD.................................................................................................................................................................5 3.2 MEASUREMENT PROCEDURE..........................................................................................................................................................5 3.3 TEST DATA.........................................................................................................................................................................................7 3.4 FIELD STRENGTH CALCULATION..................................................................................................................................................8 3.5 RADIATED TEST EQUIPMENT.........................................................................................................................................................8 3.6 MEASURING INSTRUMENT SETUP.................................................................................................................................................8 3.7 RADIATED MEASUREMENT PHOTOS.............................................................................................................................................9 4. BANDWIDTH OF EMISSION......................................................................................................................................................10 4.1 APPLICABLE STANDARD PLOT GRAPHIC OF BANDWIDTH....................................................................................................10 4.2 BANDWIDTH TEST EQUIPMENT...................................................................................................................................................10 4.3 PLOT GRAPHIC OF BANDWIDTH..................................................................................................................................................10 5. CONDUCTED EMISSION MEAS…

Text truncated - open the document above for the full version.

ETC Report No.:E90S-12-159-03Page 9 of 14 FCC ID.: P6W001 Rev. No 1.0 3.7 Radiated Measurement Photos