P9I-WGBTLPGPremier Guard BTL

WG Security Products, Inc

Click to zoom

Application Details

Equipment Class: DCD - Part 15 Low Power Transmitter Below 1705 kHz
Date of Grant: Mar 04, 2012
Application Purpose: Original Equipment
Date of Application: Mar 04, 2012
Equipment Note: Premier Guard BTL
Frequency Range: 0.05800000 - 0.05800000
Company: WG Security Products, Inc
Country: United States

Documents & Files

Select a file to view

Document Text

Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.

Users Manual

58Khz BTL Common Platform EAS Systems (EAS4.0 ver1.1 AM board) Installation Manual February 2012 Manual Part Number: (Ver. ) TM This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‧ Reorient or relocate the receiving antenna. ‧ Increase the separation between the equipment and receiver. ‧ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‧ Consult the dealer or an experienced radio/TV technician for help. The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Note: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter FCC ID: P9I-WGBTLPG “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.” WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes. WG SECURITY PRODUCTS INC. 3031 Tisch Way, Suite 602, San Jose, CA 95128 (USA) http://www.wgspi.com Technical Support Contact Information North America South America Tel: 949-545-6005 Toll Free: 888-633-5095 Fax: 949-545-6011 Email: [email protected] Rest of World Tel: 4+49 8654 7715-21 Fax: 4+49 8654 7715-21 Email: [email protected] CRITICAL NOTE As specified by FCC Regulations 15.21, any changes or modifications not expressly approved by the party responsible for compliance of this equipment, will void the user’s permission and authority to operate this equipment. TABLE OF CONTENTS OVERVIEW ................................................................................................................ 1 System Overview.................................................................................................... 1 System Configurations............................................................................................ 2 Product Names and Part Numbers ......................................................................... 3 Common Platform Features & Benefits .................................................................. 4 Specifications (common parameters) ..................................................................... 5 COMMON PLATFORM ELECTRONICS.................................................................... 6 BTL AM Board Functions Description..................................................................... 6 Antenna Channels on BTL AM Board..................................................................... 7 TX Amplitude POT on BTL AM Board .................................................................... 8 BTL AM Board to Socket Board Power Cables Connections.................................. 9 Pedestal Socket Board Connections .................................................................... 10 Fuse Replacement Information (on BTL socket Board) ........................................ 12 Pedestal Tuning Access (on BTL AM Board)....................................................... 13 SMART POWER SUPPLY (SPS) ............................................................................ 14 SPS Controls and Connections ............................................................................ 14 SPS Box Terminals Illustration ............................................................................. 15 SPS Box Main AC Input and Voltage Setup ......................................................... 16 Interconnection between Smart Power Supply and Pedestal ............................... 17 Power Cord Notices.............................................................................................. 18 SPS Box Mounting Instructions ............................................................................ 20 SPS Box External Relay interface ........................................................................ 21 Common Platform EAS Systems 1 OVERVIEW System Overview Note: Common Platform EAS Systems differ only in the antennas that are used. All systems use a universal transceiver printed circuit board that performs all the functions of…

Text truncated - open the document above for the full version.

External Photos

1. EUT Photograph (1) EUT Photo (2) EUT Photo Report No：11AS047R-RF-US-P09V01 Page: 2 of 4 (3) EUT Photo (4) EUT Photo Report No：11AS047R-RF-US-P09V01 Page: 3 of 4 (5) EUT Photo (6) EUT Photo Report No：11AS047R-RF-US-P09V01 Page: 4 of 4 (7) EUT Photo

ID Label/Location Info

Label location

Internal Photos

(1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo (10) EUT Photo

Test Report

FCC Part15C Test Report Product Name : Premier Guard BTL Model No. : BTLPG FCC ID : P9I-WGBTLPG Applicant : WG Security Products, Inc Address : 3031 Tisch Way Suite 602, San JoseUnited, States Date of Receipt : 25/10/2011 Test Date : 26/10/2011~ 09/11/2011 Issued Date : 23/11/2011 Report No. : 11AS047R-RF-US-P09V01 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national /international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, NVLAP or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No：11AS047R-RF-US-P09V01 Page: 2 of 21 Test Report Certification Issued Date : 23/11/2011 Report No. : 11AS047R-RF-US-P09V01 Product Name : Premier Guard BTL Applicant : WG Security Products, Inc Address : 3031 Tisch Way Suite 602, San JoseUnited, States Manufacturer : SHANGHAI WINGUIDE DIGITAL TECHNOLOGY LTD. Address : 79 Wu XIANG Rd. Jiading district Xuhang, shanghai Model No. : BTLPG FCC ID : P9I-WGBTLPG EUT Voltage : AC IN: 110~240V OUT: AC 26V Brand Name : WG Applicable Standard : FCC CFR Title 47 Part 15 Subpart C: 2009 ANSI C63.4: 2009; ANSI C63.10: 2009 Test Result : Complied Performed Location : Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Registration Number: 800392 Documented By : (Engineering ADM: Alice Ni) Reviewed By : (Senior Engineer: Jame Yuan) Approved By : (Engineering Manager: Marlin Chen) Report No：11AS047R-RF-US-P09V01 Page: 3 of 21 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site : http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] LinKou Testing Laboratory : No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected] Suzhou (China) Testing Laboratory : No. 99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou,China. TEL : +86-512-6251-5088 / FAX : +86-512-6251-5098 E-Mail : [email protected] Taiwan R.O.C. :BSMI, NCC, TAF Germany :TUV Rheinland Norway :Nemko, DNV USA :FCC, NVLAP Japan :VCCI Report No：11AS047R-RF-US-P09V01 Page: 4 of 21 TABLE OF CONTENTS Description Page 1. General Information .......................................................................................................5 1.1. EUT Description .........................................................................................................5 1.2. Mode of Operation .....................................................................................................6 1.3. Tested System Details................................................................................................7 1.4. Configuration of Tested System .................................................................................8 1.5. EUT Exercise Software ..............................................................................................9 2. Technical Test ..............................................................................................................10 2.1. Summary of Test Result ...........................................................................................10 2.2. Test Environment..................................................................................................... 11 3. Conducted Emission ....................................................................................................12 3.1. Test Equipment ........................................................................................................12 3.2. Test Setup ................................................................................................................12 3.3. Limit..........................................................................................................................13 3.4. Test Procedure.........................................................................................................13 3.5. Uncertainty ...............................................................................................................13 3.6. Test Result...............................................................................................................14 4. Radiated Emission.......................................................................................................16 4.1. Test Equipment ........................................................................................................16 4.2. Test Setup ................................................................................................................17 4.3. Limit..........................................................................................................................18 4.4. Test Procedure.........................................................................................................18 4.5. Uncertainty ..........…

Text truncated - open the document above for the full version.

Test Setup Photos

Test Setup Photograph Test Mode: Mode 1: Transmit Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit Description: Back View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit Description : Radiated Emission Test Setup for Below 30MHz Test Mode: Mode 1: Transmit Description : Radiated Emission Test Setup for Below 1GHz