P9I-WGWFCB58 KHz Electronic Article Surveillance System

58KHz WiFi Floor Guard & Door Guard EAS Systems (EAS5.0 ver1.6 AM board) Installation Manual March 2015 Manual Ver. 03261501 TM WG SECURITY PRODUCTS INC. 2105 S. Bascom Ave., Suite 316, Campbell, CA 95008 (USA) http://www.wgspi.com Technical Support Contact Information North America South America Tel: 408-241-8000 Fax: 408-559-2073 Email: [email protected] Rest of World Tel: +49 8654 7715-0 Fax: +49 8654 7715-29 Email: [email protected] WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes. CRITICAL NOTES As specified by FCC Regulations 15.21, any changes or modifications not expressly approved by the party responsible for compliance of this equipment, will void the user’s permission and authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TABLE OF CONTENTS OVERVIEW ..................................................................................................................... 1 System Overview ......................................................................................................... 1 System Configurations ................................................................................................. 2 Product Codes and Descriptions ................................................................................. 3 Specifications .............................................................................................................. 4 CONTROLLER CIRCUIT BOARD .................................................................................. 5 WiFi Main Board Connectors ....................................................................................... 5 System Configuration .................................................................................................. 6 PRE-INSTALLATION INFORMATION ............................................................................ 7 Quick Start for System Connections ............................................................................ 7 SMART POWER SUPPLY (WG SPS-24) ..................................................................... 12 Controls and Connections ......................................................................................... 12 Terminals Description ................................................................................................ 13 Main AC Input and Voltage Setup ............................................................................. 14 External Relay interface ............................................................................................. 15 (THIS PAGE INTENTIONALLY LEFT BLANK) WiFi Floor Guard & Door Guard EAS Systems 1 OVERVIEW System Overview All WIFI EAS Systems utilize a common controller, differing only in the antennas that are used. Pedestal controllers (Ad Guard, Ad Guard XL, Premier Guard and Premier Pro) are imbedded in the pedestal base. Door Guard and Floor Guard controllers are contained in a separate housing. In either case, the controller is comprised of a main circuit board for performing all the functions of transmitting, receiving and alarm notification. The power board facilitates all the antenna transmission. This manual applies to the WiFi Floor Guard and WiFi Door Guard. Door Guard and Floor Guard Antennas These modules contain only the antennas whose operation and power are derived from the separate Control and Adaptor boxes. WiFi Control and Adaptor Boxes The Controller Box contains the WiFi Controller and PSU (WG SPS-24) for controlling the antenna and processing tag data. Between the Control Box and Antenna is the Adaptor Box which ensures signal stability between the WiFi Controller and the antennas. The Control Box includes WiFi capability so that the systems can be synchronized and tuned remotely over the Internet. WiFi Control Box WiFi Floor Guard WiFi Adapter Box WiFi Door Guard WiFi Controller WG SPS-24 WiFi Floor Guard & Door Guard EAS Systems 2 System Configurations Each WiFi system is powered by its own dedicated SPS. The SPS not only provides 24vac power to the transceiver pedestal, but it includes some very important features.  Accepts a wide range of AC input voltage  Controls transmitter bursts for troubleshooting  Adjusts pedestal alarm volume  Provides alarm visual & audio indication and relay output  Provides Jammer Detection alarm and relay output 24vac power and data/control is carried by a single TX cable from the SPS to the controller. The WiFi Control Box can only be connected to only one adaptor and from that to only one antenna. Caution! One WiFi Control Box can only be connected with one antenna and Adapter Box. WiFi Floor Guard & Door Guard EAS Systems 3 Product Codes and Descriptions Systems Product Code Description Comment WG WFFG Floor Guard WiFi Transceiver, 6-foot Includes antennas, WiFi Control Box and Adaptor Box. WG WFDG Door Guard WiFi Transceiver, Gray Includes antenna, WiFi Control Box and Adaptor Box. WG WFDG-B Door Guard WiFi Transceive…

Text truncated - open the document above for the full version.

WG Security Products Inc., 2105 S. Bascom Ave, Suite 316, Campbell, CA 95008 • Tel: 408-241-8000 • Fax: 408-559-2073 • wgspi.com February 6, 2014 UL LLC Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL LLC to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL LLC on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

Note: The same WG WFCB Control Box is used for the Door Guard and Floor Guard. The Control Box includes the WG SPS-24 (which was previously certified for UL and CE) and the “Controller” which includes the exact same Control PCB used for the products listed under Project #1. PROJECT #2 Product Code Description WG WFDG Door Guard WG WFFG Floor Guard WG WFCB Control Box WG WFFG – Floor Guard Antenna WG WFDG – Door Guard WG WFCB – Control Box WG SPS-24 Power Supply Controller PCB Inside

PROPOSED FCC ID LABEL AND LOCATION (Placed on Controller of Floor Guard and Door Guard) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: P9I-WGWFCB WG SECURITY PRODUCTS INC. FCC ID Label Bottom of EUT WG SECURITY PRODUCTS INC. This device contains FCC ID: RGLRAKE410

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR 58 KHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM MODELS: WG WFDG and WG WFFG REPORT NUMBER: 14U17696-E1, REVISION B FCC ID: P9I-WGWFCB ISSUE DATE: APRIL 01, 2015 Prepared for WG SECURITY PRODUCTS, INC. 2105 S. BASCOM AVE. SUITE 316 CAMPBELL, CA 95008, U.S.A. Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 2 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By -- 6/26/2014 Initial Issue M. Mekuria A 3/17/2015 Update Sections 5.1, 5.5, 7.1 and 7.2 to address TCB’s questions O. Su B 4/1/2015 Update report to address TCB’s question T. Chu REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 3 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 5 5. EQUIPMENT UNDER TEST ............................................................................................... 6 5.1. DESCRIPTION OF EUT .............................................................................................. 6 5.2. DESCRIPTION OF MODELS DIFFERENCES ............................................................. 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 7 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 8 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 9 7. EMISSIONS LIMITS AND RESULTS ................................................................................10 7.1. RADIATED EMISSIONS .............................................................................................10 7.2. TX SPURIOUS EMISSIONS 9 KHz TO 30 MHz .........................................................11 7.3. RADIATED EMISSIONS 30 to 1000 MHz ...................................................................12 7.4. AC MAINS LINE CONDUCTED EMISSIONS .............................................................13 8. SETUP PHOTOS ...............................................................................................................20 8.1. RADIATED EMISSIONS BELOW 30 MHz ..................................................................20 8.2. RADIATED EMISSIONS ABOVE 30MHz ....................................................................21 8.3. AC MAINS LINE CONDUCTED EMISSIONS .............................................................22 9. EUT PHOTOS ...................................................................................................................23 REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 4 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: WG SECURITY PRODUCTS, INC. 2105 S. BASCOM AVE. SUITE 316 CAMPBELL, CA 95008, U.S.A. EUT DESCRIPTION: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM MODELS: WG WFDG and WG WFFG SERIAL NUMBER: A0-70-50- 14/04-00001 DATE TESTED: MAY 7, 8 & 12, 2014 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass * Models differences are explained within the body of this report. UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alterat…

Text truncated - open the document above for the full version.

REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 20 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 8. SETUP PHOTOS 8.1. RADIATED EMISSIONS BELOW 30 MHz RADIATED EMISSIONS BELOW 30MHz BACK, WG WFFG RADIATED EMISSIONS BELOW 30MHz FRONT, WG WFFG REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 21 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 8.2. RADIATED EMISSIONS ABOVE 30MHz RADIATED FRONT PHOTO, WG WFFG RADIATED BACK PHOTO, WG WFFG REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 22 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 8.3. AC MAINS LINE CONDUCTED EMISSIONS LINE CONDUCTED FRONT PHOTO, WG WFFG LINE CONDUCTED BACK PHOTO, WG WFFG REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 23 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 9. EUT PHOTOS WG WFFG, PEDESTAL (ANTENNA ONLY) WG WFDG, PEDESTAL (ANTENNA ONLY) REPORT NO: 14U17696-E1B DATE: APRIL 01, 2015 EUT: 58 kHz ELECTRONIC ARTICLE SURVEILLANCE SYSTEM FCC ID: P9I-WGWFCB MODELS: WG WFDG and WG WFFG Page 24 of 24 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. END OF REPORT POWER SUPPLY & WIFI CONTROL BOX ANTENNA ASSEMBLY (INSIDE THE PEDESTAL) AND WIFI ADAPTER BOX