P9J-24112.4 GHz 802.11n High Power Mini-PCI Card

Part No. 200315-00 Rev A0 July, 2008 Tropos ® Networks MetroMesh™ Router Outdoor Installation Guide Models 6310 and 6320 trpo_013 Tropos Networks, Inc. 555 Del Rey Ave. Sunnyvale, CA 94085 USA www.troposnetworks.com 408-331-6800 Tropos MetroMesh Routers Installation Guide, Models 6310 and 6320ii Copyright Notice ©2003-2008 Tropos Networks, Inc. All rights reserved. Tropos and PWRP are registered trademarks of Tropos Networks, Inc. Tropos Networks, MetroMesh, AMCE, TMCX, SABRE, CMDP, MESM and Metro-Scale Mesh Networking Defined are trademarks of Tropos Networks, Inc. Loctite is a registered trademark of Loctite Corporation, USA. All other brand or product names are trademarks or registered trademarks of their respective holder(s). Information contained herein is subject to change without notice. The only warranties for Tropos products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Tropos shall not be liable for technical or editorial errors or omissions contained herein. This product includes technology protected by U.S. Patents 6,704,301; 6,965,575; 7,016,328; 7,031,293; and 7,058,021. FCC Notice to Users and Operators This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by using one of the following measures: „Reorient or relocate the receiving antenna. „Increase separation between the equipment and receiver. „Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. „Consult the dealer or an experienced radio/TV technician. This Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by Tropos Networks could void the user's authority to operate this device. Industry Canada Notice to users and operators: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des réglements d’équipement. L’opération est sujette aux deux conditions suivantes : (1) cet dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l'interférence qui peut causer l’opération peu désirée. Warning It is illegal to modify the construction of this product. Modifying the operating frequency or enhancing the transmit output power through the use of external amplifiers or other equipment is specifically disallowed by the “Telecommunications Act.” Tropos MetroMesh Routers Installation Guide, Models 6310 and 6320iii Warning This device is for outdoor or indoor use with conditions that no harmful interference to authorized radio stations results from the operation of this device. This device shall not influence aircraft security and/or interfere with legal communications as defined in the “Telecommunications Act.” If this device is found to cause interference, the operator of this equipment shall cease operating this device immediately until no interference is achieved. European Union WEEE Notice It is important for users of this equipment to participate in reuse, recycling, and other forms of recovery. The potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment are a waste of natural resources and cause pollution. For EU member countries, this symbol means: Do not dispose of this equipment as unsorted municipal waste. This equipment must be collected separately. The return and collection of this product has not been defined at this time, please contact Tropos Networks for return and/or collection. Tropos MetroMesh Routers Installation Guide, Models 6310 and 6320iv European Community Language Versions of Informal Statement for Inclusion in User Information The following statements are in accordance with Article 6.3 of Directive 1999/5/EC. 5320 5320 5320 5320 5320 5320 5320 5320 5320 5320 5320 5320 5320 5320 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 6320 6310 Tropos MetroMesh Routers Installation Guide, Models 6310 and 6320v STOP!! STOP!! STOP!! STOP!! READ THIS FIRST! Important Safety Instructions The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with an arrowhead symbol wit…

Text truncated - open the document above for the full version.

April 16, 2007 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize THOMAS N COKENIAS, d.b.a. T.N. Cokenias Consulting, to act on our behalf in all manners relating to application for equipment authorization through the Certification Division of Compliance Certification Services (CCS) , including signing of all documents relating to these matters. Any and all acts carried out by THOMAS N COKENIAS on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing THOMAS N COKENIAS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) ndeavor to ensure that no certificate or report nor any part thereof is used in a h) nsure that any reference to our product certification in communication media such as n i) eep a record of all complaints made known to the us relating to the product’s s j) take appropriate action with respect to such complaints and any deficiencies found in k) document the actions taken. his authorization is valid until further written notice from the applicant. incerely Yours, works e misleading manner; e documents, brochures or advertising, complies with the requirements of the Certificatio Division; k compliance with requirements of the relevant standard and to make these record available to the Certification Division when requested; products or services that affect compliance with the requirements for certification; T S Jay Kruse Tropos Net

tel: 650-726-1263 fax: 650-726-1252 [email protected] Thomas N. Cokenias EMC &Radio Approvals Test & Consulting Services for Commercial, Military, International Compliance P.O. Box 1086 El Granada, CA 94018 Compliance Certification Services 9 September 2008 47173 Benicia Street Fremont CA Attention: Application Examiner Reviewing Engineer RE: Request for confidentiality per FCC Rule Sections 0.457 and 0.459 Applicant: Tropos Networks Inc. FCC ID: P9J-2411 To whom it may concern, Request is hereby submitted, on behalf of my client Tropos to withhold from public review indefinitely certain portions of the application for equipment certification for the referenced FCC identifier. The referenced product is a 2.4GHz radio module for which limited modular approval is sought. In particular, the following sections of the application and report are requested to be kept confidential: Operational Description Schematic Block Diagram Module internal and external photographs. Rationale for request for confidentiality: Tropos has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would give them competitive advantage in developing similar products. Justification for the special request to keep photographs confidential is that the product is professionally installed, is not sold or distributed in retail channels, and is owned and installed by municipalities. The products are installed on poles or roof-tops, and are inaccessible to routine casual inspection. If you have questions or need further information, please contact the undersigned. Sincerely, THOMAS N. COKENIAS EMC Consultant/Agent for Tropos Networks

Applicant/Grantee Tropos Networks Inc. FCC ID: P9J-2411 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The module has a metal shield over the radio elements YES 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Buffered data inputs are in place YES 3 The modular transmitter must have its own power supply regulation. The module has its own power supply regulation YES 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The antennas used with the final product incorporating this module will be professionally installed, and is consistent with the requirements of a limited modular approval YES 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and su pporting The module was tested in a pcmcia to miniPCI adapter connected to a laptop computer YES equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The RF module label is submitted as a separate exhibit. YES 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The module is installed only in products manufactured by the grantee and under the grantee’s control, in keeping with the requirements for a limited modular approval. The grantee has internal manufacturing processes and documentation for control of final products using this module. YES 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The module complies MPE limits as stated in the product manual when using the antennas described in the filing YES A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is alwa…

Text truncated - open the document above for the full version.

Customer: Ticket No: Size: P.O. No.: Part No.: Face Stock: Ink Color(s): Date: Quantity: Indiv.Cut Sheeted Laser Cut Die Cut Radius Laminated Unwind # Core Dia. No. Per Roll Consec. No. Start: Slit Liner Perf'd. Pin Feed Fan Fold Typewriter Feed Window Appl TypeTab Peel Tab Embossed Adh. End: This Proof is the Property of Cellotape. All Rights Reserved. WE CAN NOT PROCEED WITH THIS ORDER UNTIL WE HAVE YOUR APPROVAL. PLEASE CHECK AND RETURN IMMEDIATELY. IF THERE ARE ANY CHANGES IN QUANTITY, SIZE, STOCK, INK, OR COPY YOU MUST NOTIFY OUR OFFICE BY PHONE. THIS IS A COPY OF THE ARTWORK. THE COLORS, SURFACE TEXTURE AND ADHESIVE ARE NOT INTENDED TO REPRESENT THOSE OF THE FINISHED PRODUCT. IMPORTANT PLEASE READ THIS ORDER IS FOR PRINTED MATTER AND THEREFORE NOT SUBJECT TO CANCELLATION. ANY PROOFS NOT REACHING PRINTING STAGE WITHIN 90 DAYS ARE SUBJECT TO A SET UP CHARGE (MIN. $45.00). YOUR DELIVERY DATE DEPENDS UPON THE PROMPT RETURN OF THIS PROOF. PROOF MUST BE SIGNED AND APPROPRIATE BOX MUST BE CHECKED . FOR A RUSH APPROVAL, CALL CUSTOMER SERVICE BEFORE RETURNING PROOF. APPROVEDAPPROVED, changes notedNOT APPROVED, send new proof 47623 Fremont Blvd., Fremont, CA 94538 Ph: (510) 651-5551 Fax: (510) 651-8091 www.cellotape.com Proof By: SIGNED BY: Form 4.9.21.A9 REV C Page of Please call and Fax with approvals and corrections. P R O O F Uncontrolled Document If Printed - For Reference Only Model: GDH INPUT: 20-60 VDC 63203030 NOTE: Installer must be a trained technical professional. 300158-00 Rev A0 CONTAINS FCC ID: P9J-2411 CONTAINS FCC ID: P9J-5805 IC: 4751A-2411 IC: 4751A-5805 PROTECTED BY U.S. PATENTS OUTDOOR USE Menchu Ventura 06 . 18 . 2008 162376 3.000" x 3.000" E8052802 151283-00 0.125" 11 White Vinyl Scotchcal Black, 9720 UV Overcoat Tropos Network Art Only Actual Size (3.000"W x 3.000"H) 1 s t 1. TEXT & GRAPHICS PRINT BLACK IN COLOR 3. DASHED LINE INDICATES DIE CUT, LINE DOES NOT PRINT 2. BACKGROUND REMAINS WHITE STOCK COLOR

Customer: Ticket No.: Size: P.O. No.: Part No.: Stock: Ink Color(s): Date: Quantity: Indiv. Cut Sheeted Laser Cut Die Cut Radius Laminated Unwind # Core Dia. No. Per Roll Consec. No. Start: Slit Liner Perf'd Pin Feed Fan Fold Typewriter Feed Window Appl TypeTab Peel Tab Embossed Adh. End: WE CAN NOT PROCEED WITH THIS ORDER UNTIL WE HAVE YOUR APPROVAL. PLEASE CHECK AND RETURN IMMEDIATELY. IF THERE ARE ANY CHANGES IN QUANTITY, SIZE, STOCK, INK, OR COPY YOU MUST NOTIFY OUR OFFICE BY PHONE. THIS IS A COPY OF THE ARTWORK. THE COLORS, SURFACE TEXTURE AND ADHESIVE ARE NOT INTENDED TO REPRESENT THOSE OF THE FINISHED PRODUCT. IMPORTANTIMPORTANT PLEASE PLEASE READREAD IMPORTANT PLEASE READ THIS ORDER IS FOR PRINTED MATTER AND THEREFORE NOT SUBJECT TO CANCELLATION. ANY PROOFS NOT REACHING PRINTING STAGE WITHIN 90 DAYS ARE SUBJECT TO A SET UP CHARGE (MIN. $45.00). YOUR DELIVERY DATE DEPENDS UPON THE PROMPT RETURN OF THIS PROOF. PROOF MUST BE SIGNED AND APPROPRIATE BOX MUST BE CHECKED. FOR A RUSH APPROVAL, CALL CUSTOMER SERVICE BEFORE RETURNING PROOF. APPROVEDAPPROVED, Changes NotedNOT APPROVED, Send New Proof 47623 Fremont Blvd., Fremont, CA 94538 Ph: (510) 651-5551 Fax: (510) 651-8091 www.cellotape.com SIGNED BY: Form 4.9.21.A9 REV C Proof By: Page of Please call and Fax with approvals and corrections. This Proof is the Property of Cellotape. All Rights Reserved. PROOF2nd 163091 .25” x .8” E8072402 151362-00 .03”. N/A N/AN/A 11 N/AN/AN/A WHITE VINYL SCOTCHCAL BLACK 9705 UV & 9702 UV OVERCOAT TROPOS NETWORKS ART ONLY 7-30-2008 Menchu TEXT PRINTS BLACK 9705 V 9702 UV OVERCOAT BACKGROUND REMAINS WHITE STOCK COLOR DASHED LINE INDICATES DIE CUT, LINE DOES NOT PRINT ENLARGED 200% FOR PROOF FCC ID: P9J-2411 FCC ID: P9J-2411

Sheet1 T r o p o s N e t w o r k s F C C I D : P 9 J - 2 4 1 1 W i r e l e s s r o u t e r r a d i o m o d u l e C a l c u l a t e m W / c m 2 h e r e . E n t e r f r e q u e n c y i n M H z : 2 . 4 G H z 8 0 2 . 1 1 b g R F H a z a r d D i s t a n c e C a l c u l a t i o n Calculation of Limits from 1.1310 Table 1 Controlled Uncontrolled Ave 6 min Ave 30 min m W / c m 2 f r o m T a b l e 1 : 1 . 0 0 F(MHz) A A c t u a l F , M H z Occ, mW/c2 Gen, mW/cm2 0.3-3 0.5 100.0 100.0 Max RF Power TX Antenna MPE distance S, mW/cm@ Comment 3.0 - 30.0 5 180.0 36.0 P, dBm G, dBi cm at 20 cm 3 3 0 . 0 - 3 0 0 5 5 1 . 0 0 . 2 300-1500 902 3.0 0.60 28.6 6.00 15.1 0.57 6 dBi p2mp 1500-100000 5555 5.0 1.0 28.6 7.40 17.7 0.78 7.4 dBi p2mp 24.0 12.00 17.8 0.79 12 dBi p2mp 28.6 12.00 30.2 2.28 12 dBi p2p E E n t e r P ( m W ) Equivalent dBm E E n t e r d B m Equivalent Watts B a s i s o f C a l c u l a t i o n s : 8 9 5 . 4 2 9 . 5 2 2 9 . 5 2 895.4 E^2/3770 = S, mW/cm2E, V/m = (Pwatts*Ggain*30)^.5/d, metersd = ((Pwatts*G*30)/3770*S))^0.5 Pwatts*Ggain = 10^(PdBm-30+GdBi)/10) S@20cm = 20 log (MPE dist/20cm) N O T E : F o r m o b i l e o r fi x e d l o c a t i o n t r a n s m i t t e r s , m i n i m u m s e p a r a t i o n d i s t a n c e i s f o r F C C c o m p l i a n c e i s 2 0 c m , e e v e n i f c a l c u l a t i o n s i n d i c a t e M P E d i s t a n c e i s l e s s Page 1

Report No: 08PRO13 Date: 5 August 2008 2.4 GHZ Fixed WLAN Transceiver FCC ID: P9J-2411 Page 55 of 59 SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP Report No: 08PRO13 Date: 5 August 2008 2.4 GHZ Fixed WLAN Transceiver FCC ID: P9J-2411 Page 56 of 59 RADIATED RF MEASUREMENT SETUP 6 dBi Antenna Report No: 08PRO13 Date: 5 August 2008 2.4 GHZ Fixed WLAN Transceiver FCC ID: P9J-2411 Page 57 of 59 7.4 dBi Report No: 08PRO13 Date: 5 August 2008 2.4 GHZ Fixed WLAN Transceiver FCC ID: P9J-2411 Page 58 of 59 12 dBi antenna Report No: 08PRO13 Date: 5 August 2008 2.4 GHZ Fixed WLAN Transceiver FCC ID: P9J-2411 Page 59 of 59 POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP END OF REPORT