
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Part No. 200081-00 Rev A1 November 30, 2004 Tropos Networks Outdoor Wi-Fi Cell Installation Guide Model 5210 Tropos Networks, Inc. 555 Del Rey Ave. Sunnyvale, CA 94085 USA www.troposnetworks.com 408-331-6800 Tropos 5210 Wi-Fi Cell Installation Guideii Copyright Notice ©2004 Tropos Networks, Inc. All rights reserved. Tropos Networks is a registered trademark of Tropos Networks, Inc. in the United States and certain other jurisdictions. Specifications are subject to change without notice. Loctite is a registered trademark of Loctite Corporation, USA. FCC Notice to Users and Operators This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by using one of the following measures: Reorient or relocate the receiving antenna. Increase separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician. This Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by Tropos Networks could void the user's authority to operate this device. VCCI Notice to Users and Operators Translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a Japanese domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Tropos 5210 Wi-Fi Cell Installation Guideiii Taiwan DGT Telecommunications Act Notice to Users and Operators Warning It is illegal to modify the construction of this product. Modifying the operating frequency or enhancing the transmit output power through the use of external amplifiers or other equipment is specifically disallowed by the “Telecommunications Act.” Warning This device is for outdoor or indoor use with conditions that no harmful interference to authorized radio stations results from the operation of this device. This device shall not influence aircraft security and/or interfere with legal communications as defined in the “Telecommunications Act.” If this device is found to cause interference, the operator of this equipment shall cease operating this device immediately until no interference is achieved. Note This device must be installed by trained professional, value added reseller or systems integrator who is familiar with RF cell planning issues and the regulatory limits defined by the Taiwan government “Telecommunications Act” for RF exposure, specifically those limits outlined in Telecom Technical Regulations RTTE01 and LP002. 低功率電波輻性電機管理辦法 第十四條經型式認證合格之低功率射頻電機,非經許可,公司、商號或使 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十七條低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發 現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 Tropos 5210 Wi-Fi Cell Installation Guideiv STOP!! STOP!! STOP!! STOP!! READ THIS FIRST! Warning You can be killed installing this device! You can be killed if the cell antennas come near electric power lines. Carefully read and follow all instructions in this manual. By nature of the installation, you may be exposed to hazardous environments and high voltage. Use caution when installing the outdoor system. Caution The Tropos 5210 Outdoor Wi-Fi cell may contain a lithium-ion battery. To avoid the possibility of an explosion, the Tropos 5210 Wi-Fi cell should NOT be exposed to any temperatures higher than 85 degrees C. The RJ45 connectors of your Tropos 5210 Outdoor Wi-Fi cell may source DC power on pins 4,5 and 7,8. The IEEE 802.3 standards allow for pins 4,5 and 7,8 to be used for Power Over Ethernet. Some products may be incompatible with the Tropos Power Over Ethernet capability. If such problems occur, make sure that the unit is configured with the Power Over Ethernet capability set to Off (default setting). If problems persist, use Ethernet cables that have no connections to the unused pins 4,5 and 7,8. The Tropos 5210 Outdoor Wi-Fi cell is installed in wet, outdoor locations. Make sure closure caps are installed and all cable connections are securely fastened and waterproofed. The Tropos 5210 Outdoor Wi-Fi cell can only be used with approved antennas. See Appendix C, “Approved Antenna Configurations” for further information. Tropos 5210 Wi-Fi Cell Installation Guidev Contents Installing the Tropos 5210 Wi-Fi Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Site Planning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Location Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Antenna Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Site Surveys . . . . . . . . . . . . . . . . . . . . . . . . . . . .…
Text truncated - open the document above for the full version.
October 21, 2004 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Re: Request for Confidentiality In reference to the Permissive Change under FCC ID: P9J-52101000, and pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of the accompanying information as outlined below: Document titled "Block Diagram", total 1 page. Document titled "Theory of Operation", total 2 pages. Document titled "Schematic Diagram – Tropos 5210 Radio", total 5 pages. Document titled "Schematic Diagram – Tropos 5210 Mother Board", total 11 pages. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Thomas Blais Director of Hardware Engineering Tropos Networks, Inc. (650) 655-4979 tel (650) 286-4259 fax [email protected]
1 Helen Zhao From:Claire Hoque Sent:Monday, November 22, 2004 11:39 AM To:Helen Zhao Cc:Julia Luke; Nancy Omron; Yan Zheng Subject:answer: TCB questions for Tropos Networks, Inc., FCC ID: P9J-52101000, Assessment NO.: AN04T4304, Notice#1 Importance:High Hi Helen, Here are the answers. Question #1: The theory of operation indicated that the device can be used with four antennas for diversity, each with a maximum gain of 7.4dBi (Omni Antenna), 9.9dBi (Omni Antenna), 12dBi (Omni Antenna) and 12dBi (Sector Patch type Antenna). It also shows the conducted output power is set differently, when a 7.4dBi gain or a 12dBi gain antenna is used. The end-user can order the specific antenna they want for model 52102100, please explain who will provide output power adjustment when any one of the antenna is chosen to install and how the applicant makes certain the final product on the market will be totally tuned to be compliant with FCC rule and limits. <Tropos> The trained technical professional is responsible for lowering the conducted TX power by configuring the equipment when higher gain antennas are used. The 5210 has a TX attenuation setting which the installer must configure. The TX attenuation setting is factory calibrated, as is the conducted TX power of the 5210. Instructions for setting the TX attenuation setting for the high gain antennas is detailed in Appendix C of our installation guide. We have attached the latest copy of the guide in case you may have an older version. Also attached is a screen shot of the TX attenuation setting control on the 5210. 5210 Guide 04-11-09.pdf TransmitAttenuatio nControl_Scr... Question #2: The test report provides the output power test results when a 7.4dBi gain and a 12dBi gain antenna are used. What is the output power when a 9.9 gain omni antenna is used? How does the device meet FCC15.247(b)(4) requirement? <answer>test report is revised. 04U3022-1 FCC DTS Report(revis... Question #3: Appendix 3 U.S. Approved Antenna Configurations of the user manual does not specify clearly the configurations each model will have, and the eirp with each antenna. 9.9 dBi omni antenna is not on the list. Please update. <answer>test report is revised. Question #4: Please provide external photo of bottom view of model 52102100, 52102200. <answer>external photos are revised. 2 External Photos(revised).pdf Question #5: The functional block diagram is incomplete, the right side is missing. Please resubmit a complete copy. <answer>pls see revised block diagram. Tropos-5210-Functi onal_Block_D... Thanks, Claire
PROPOSED FCC ID LABEL AND LOCATION TROPOS NETWORKS, INC. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: P9J-52101000 FCC ID LABEL LOCATION
GP-24S 2.4GHz Omnidirectional Base Antenna GP-24S Specifications • 2400-2500Mhz • VSWR: less than 1.5:1 • Gain: 9.9dBi • Length: 3 ft 9 inches • Weight: 1 lbs 14 oz (inc brackets) • -3dB Beam-width: 9 degrees • Cross polar rejection: 20dB+ • Max Power: 100 watts • Max Wind Survival: 150MPH • Wind Load: 26.9 sq in (0.187 sq ft) • Mast Required: 1.25-2.5 inches • Connector: Weather protected integral N- female • Radome: Heavy wall one piece white UV stabilized fiberglass. • Mounting hardware included Vertical radiation pattern FEATURES • High gain omnidirectional pattern for me- dium to long range point-to-multipoint applications plus excellent fill-in beneath the antenna. • The mounting pipe protects the coax to antenna connection from rain/ice/ moisture. • Heavy duty fiberglass radome, 150+ MPH wind survival • Extruded aluminum mounting brackets, stainless steel u-bolts/hardware. • Ideal for the license free 2.4GHz ISM band using the 802.11b and 802.11g standards. NCG COMPANY 1275 N. Grove St. Anaheim, CA 92806-2114 Phone: 800.962-2611 Fax: 714.630-7024 email: [email protected]
48 Perimeter Road, Manchester, NH 03103 • Phone: 603-627-7877 • Fax: 603-627-1764 • E-mail: [email protected] Web Site: www.cushcraft.com COMMUNICATIONS ANTENNAS ModelFreq.GainVSWRPolarization-3dB bmwidthWeightRF ConnectorDimensionsPowerMount MHzdBiE-Plane H-Planelb (kg)(f)in. (cm)(Watts)Style S2401290P12NF2400-2500122.0:1Linear10º 90º1.0 (.45)N3 x 26 x 1 (7.6 x 66 x 2.5)50Wall/Mast S1851290P12NF1850-1990122.0:1Linear10º 90º1.6 (.73) N34 x 3 x 1.2 (86.4 x 7.6 x 3.0)50Wall/Mast S1711290P12NF1710-1880122.0:1Linear10º 90º1.6 (.73)N34 x 3 x 1.2 (86.4 x 7.6 x 3.0)50Wall/Mast H-Plane E-Plane 2.4-2.5 GHz. 12 dBi, 90 Degree Sectored and Wide Angle Coverage Directional Antenna Cushcraft’s 12 dBi gain, 90 degree “Wide H-plane” sectored antenna offers the systems integrator both an antenna for use with sectorized base stations and a wide area coverage directional antenna for use where a wide directional pattern characteristic would be preferable to an omnidirectional pattern characteristic. Enclosed in an attractive UV-stable weatherproof radome, it is both attractive enough to satisfy indoor aesthetic requirements and rugged enough to withstand outdoor exposures. Anywhere from one to four of the 90 degree sectored antennas can be deployed at a base station site depending on the area coverage that is called for and single antennas can be mounted to a wall or mast to provide wide area directional coverage. The TM905BRK mechanical down-tilt mount can be used to mount the antenna to a mast and can also be used to customize the antenna pattern tilt whether mounting to a mast or a wall surface. The design is both electrically and mechanically robust ensuring a lifetime of stable, trouble-free service and predictable, reliable, consistent performance. The standard antenna comes with a 12-inch low-loss coaxial pigtail and N female connector. Alternative coax cable lengths and connector types are also available. SPECIFICATION CHART • Wide 90 degree H-plane coverage • Indoor/outdoor antenna • Tilt and articulating mounts available • Low visibility housing HIGH GAIN PATCH PRODUCT DATA SHEET S2401290P S2401290P 330 ° 0 ° 270 ° 60 ° 30 ° 300 ° 90 ° 240 ° 210 ° 180 ° 150 ° 120 ° 30 20 10 20 30 10 30 20 10 20 30 10
SF-245W 2.4GHz Omnidirectional Antenna Specifications: • 2400-2500MHz • Gain: 7.4dBi • Length: 17.5 inches • Weight: 4.7 oz • -3dB Beam-width: 20 degrees • Cross Polar Rejection: 15dB + • Max Power: 50 watts • Max wind survival: 150MPH + • Wind Load: 7.1 sq in • Connector: Integral N-male • Radome: White UV stabilized fiberglass • Mast mounting hardware optional • Mobile lip mount optional • Mobile permanent mount optional 1275 N. Grove St. Anaheim, CA 92806-2114 Phone: 800.962.2611 Fax: 714.630.7024 Email: [email protected] NCG Company Vertical radiation pattern FEATURES: • 802.11b and 802.11g compatible • Designed for use as either a me- dium gain base antenna or a high gain mobile antenna. • Male N-connector for easy installa- tion • Compact gain antenna for point- to-multipoint applications • Heavy duty fiberglass for durability • Weather proof for indoor or out- door installation MOUNTING OPTIONS: • MB-100: 1”-2.5” mast mount • GR-5N: Mobile lip mount • 5D4N : 5/8 inch hole mount GR-5N mobile trunk lip mount 5D4N hole mount MB-100 mast mount Manufactured by: COMET Company Ltd.
FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION MODEL SERIES: 52102100, 52102200, 52103000, 52103100 FCC ID: P9J-52101000 REPORT NUMBER: 04U3022-1 ISSUE DATE: OCTOBER 20, 2004 Prepared for TROPOS NETWORKS 555 DEL REY AVENUE SUNNYVALE, CA 94085 U.S.A. Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 *Details of specific model(s) tested and model differences shall be identified in body of report REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 2 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. Revision History Rev. Revisions Revised By 001 Took out the PSD & Conducted Spurious plots and data for Yan Zheng 12dBi Antenna 002 Added three models to the EUT Danielle Zhan 003 Added one Omni antenna with a max. gain of 9.9dBi Danielle Zhan REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 3 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. TEST RESULT DECLARATION .................................................................................................... 4 2. EUT DESCRIPTION.......................................................................................................................... 5 2.1. Model difference ........................................................................................................................... 5 3. TEST METHODOLOGY .................................................................................................................. 6 4. FACILITIES AND ACCREDITATION .......................................................................................... 6 5. CALIBRATION AND UNCERTAINTY.......................................................................................... 7 5.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 7 5.2. MEASUREMENT UNCERTAINTY ............................................................................................... 7 5.3. TEST AND MEASUREMENT EQUIPMENT................................................................................ 8 6. SETUP OF EQUIPMENT UNDER TEST ....................................................................................... 9 7. APPLICABLE LIMITS AND TEST RESULTS ........................................................................... 11 7.1. CHANNEL TESTS FOR THE 2400 TO 2483.5 MHz BAND ...................................................... 11 7.1.1. 6 dB BANDWIDTH ........................................................................................................... 11 7.1.2. 99% BANDWIDTH............................................................................................................ 18 7.1.3. PEAK OUTPUT POWER .................................................................................................. 25 7.1.4. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 39 7.1.5. AVERAGE POWER........................................................................................................... 42 7.1.6. PEAK POWER SPECTRAL DENSITY ............................................................................ 44 7.1.7. CONDUCTED SPURIOUS EMISSIONS.......................................................................... 51 7.2. RADIATED EMISSIONS.............................................................................................................64 7.2.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 64 7.2.2. TRANSMITTER ABOVE 1 GHz FOR 2400 TO 2483.5 MHz BAND WITH 7.4dBi OMNI ANTENNA.............................................................................................................................. 67 7.2.3. TRANSMITTER ABOVE 1 GHz FOR 2400 TO 2483.5 MHz BAND WITH 12dBi OMNI ANTENNA ......................................................................................................................................... 85 7.2.4. TRANSMITTER ABOVE 1 GHz FOR 2400 TO 2483.5 MHz BAND WITH 12dBi SECTOR ANTENNA ....................................................................................................................... 103 7.2.5. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz WITH 7.4dBi OMNI ANTENNA ....................................................................................................................................... 121 7.2.6. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz WITH 12dBi OMNI ANTENNA ....................................................................................................................................... 125 7.2.7. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz WITH 12dBi SECTOR ANTENNA ....................................................................................................................................... 129 7.3. POWERLINE CONDUCTED EMISSIONS .............................................................................. 133 8. SETUP PHOTOS ............................................................................................................................ 137 R…
Text truncated - open the document above for the full version.
REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 137 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 138 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED RF MEASUREMENT SETUP 7.4dBi OMNI ANTENNA RADIATED FRONT PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 139 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED BACK PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 140 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED RF MEASUREMENT SETUP 12dBi OMNI ANTENNA RADIATED FRONT PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 141 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED BACK PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 142 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED RF MEASUREMENT SETUP 124dBi SECTOR ANTENNA RADIATED FRONT PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 143 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED BACK PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 144 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 04U3022-1 DATE: OCTOBER 20, 2004 EUT: 802.11 b/g OUTDOOR WI-FI CELLULAR BASE STATION FCC ID:P9J-52101000 Page 145 of 145 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. END OF REPORT LINE CONDUCTED BACK PHOTO
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.41 GHz - 2.46 GHz | 714.50 mW |

Router with Bluetooth and LTE
Equipment Class
DTS - Digital Transmission System
5.8 GHz Wi-Fi Module
Equipment Class
NII - Unlicensed National Information Infrastructure TX
2.4 GHz Wi-Fi Module
Equipment Class
DTS - Digital Transmission System
Bluefin 5G
Equipment Class
NII - Unlicensed National Information Infrastructure TX
Bluefin 2.4G
Equipment Class
DTS - Digital Transmission System