P9JSP-01-00C-CSmartpoint/Routepoint Wireless Router

10039 Rev. A FHP Wireless, Inc. All rights reserved. Suite 304 San Mateo, CA 94402 USA 1710 South Amphlett Boulevard FHP Wireless, Inc. Copyright © 2002 FHP SmartPoint and RoutePoint Wireless Router Professional Hardware Installation Guide For Model Numbers: SP-01-00C-C-N-00 and RP-01-00C-C-N-00 2 FCC Notice to Users and Operators FCC Notice to Users and Operators The SmartPoint TM and RoutePoint TM wireless routers comply with Part 15 of the FCC rules. Operation of the SmartPoint and RoutePoint wireless routers is subject to the following two conditions: 1This device may not cause harmful interference, and 2This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by using one of the following measures: • Reorient or relocate the receiving antenna. • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician. Caution This Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by FHP Wireless could void the user's authority to operate this device. Introduction The FHP SmartPoint and RoutePoint Wireless Router Professional Hardware Installation Guide provides installation instructions for the SmartPoint and RoutePoint wireless routers and is intended for a trained technical professional. Operation and network configuration for the SmartPoint and RoutePoint wireless routers are detailed in the FHP SmartPoint and RoutePoint Wireless Router Configuration Guide. The installation instructions in this guide apply to the following SmartPoint and RoutePoint wireless router model numbers: • FHP RoutePoint RP-01-00C-C-N-00 (Antennas not provided) • FHP SmartPoint SP-01-00C-C-N-00 (Antennas not provided) 3 About FHP Wireless Networking The SmartPoint and RoutePoint wireless routers may be configured with one of the following antenna options. (Antennas ordered separately.) • AN-015-OM-UM-N 1.5 dBi omni-directional unit mounted antenna; N (male) connector • AN-050-OM-UM-N 5.0 dBi omni-directional unit mounted antenna; N (male) connector • AN-074-OM-UM-N 7.4 dBi omni-directional unit mounted antenna; N (male) connector • AN-120-SP-WM-N 12.0 dBi 90 degree sector patch wall mounted patch antenna; N (male) connector NoteThe FHP SmartPoint and RoutePoint wireless routers must be installed by a trained professional, value added reseller, or systems integrator who is familiar with RF cell planning issues and the regulatory limits defined by the FCC for RF exposure, specifically those limits outlined in sections 1.1307. About FHP Wireless Networking To better understand how an FHP wireless networking system works, it is helpful to compare it to more common 802.11b systems. Typical 802.11b access points must be “hardwired” to your internal network. To install a typical access point, you connect the Ethernet port on the access point to a hub or switch port on your internal network. Each access point acts as an extension to your wired network by serving as a bridge, connecting clients to your internal network. Figure 1 is an example of a standard access point network. Figure 1Standard Access Point Network The FHP SmartPoint and RoutePoint wireless routers function very differently than traditional, wired-access points. For example, for a small or large FHP network installation only a small number of SmartPoint and RoutePoint wireless routers need to be hardwired to your internal network. In fact, only one RoutePoint device needs to be connected to your internal network to provide connectivity fhp_003 Wireless user APAP AP Your "wired" network 4 Introduction for wireless users. For many wireless networks, one wired RoutePoint gateway is all that is needed. For added redundancy and additional bandwidth for larger wireless networks, additional gateways can be added as necessary. Non-wired SmartPoint wireless routers (nodes) function independently to form large, routed wireless networks. All you need is power for the SmartPoint wireless routers, and you can expand your wireless network by adding nodes to the network. In this way, you can build large, routed wireless networks covering areas traditionally hard to reach due to the hardwire limitation of the Ethernet connections. SmartPoint and RoutePoint wireless routers automatically configure themselves to form clusters around each wired gateway. No user intervention is required and no knowledge of routing protocols is necessary to configure your network. Each device needs some basic configuration information (ESSID, WEP Key, and so on), but other than that, your wireless network configures itself and performs all routing functions in the background. Even the IP addresses on the wireless network are automatically configured and preset at the factory, enabling true “plug-and-play” configuration of your FHP SmartPoint or RoutePoint wireless router. NoteRefer to the FHP SmartPoint and RoutePoint Wireless Route…

Text truncated - open the document above for the full version.

August 26, 2002 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Re: Request for Confidentiality In reference to the application under FCC ID: P9JSP-01-00C-C, and pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of the accompanying information as outlined below: Document titled "Technical Description", total 1 page. Document titled "Block Diagram", total 1 page. Document titled "Theory of Operation", total 1 page. Document titled "Schematic Diagram", total 1 page. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Thomas Blais Director of Hardware Engineering (650) 655-4979 tel (650) 286-4259 fax [email protected]

PROPOSED FCC ID LABEL AND LOCATION FCC ID LABEL FHP WIRELESS INC. This device complies with Part 15 of FCC rules. FCC ID: P9JSP-01-00C-C

FCC CFR47 PART 15 SUBPART C CERTIFICATION AND FCC CFR47 PART 15 SUBPART B VERIFICATION TEST REPORT FOR FHP WIRELESS, INC. SMARTPOINT / ROUTEPOINT WIRELESS MESHED ROUTER MODEL NUMBER: RP-01-00C-C-N-00, SP-01-00C-C-N-00 FCC ID: P9JSP-01-00C-C REPORT NUMBER: 02U1392-1 ISSUE DATE: AUGUST 28, 2002 Prepared for FHP WIRELESS, INC. 1730 S. AMPHLETT BLVD. SAN MATEO, CA 94402 USA Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 2 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION.................................................................................................3 2. EUT DESCRIPTION.........................................................................................................................4 3. TEST METHODOLOGY..................................................................................................................5 4. FACILITIES AND ACCREDITATION..........................................................................................5 4.1. FACILITIES AND EQUIPMENT.................................................................................................5 4.2. LABORATORY ACCREDITATIONS AND LISTINGS.................................................................5 4.3. TABLE OF ACCREDITATIONS AND LISTINGS........................................................................6 5. CALIBRATION AND UNCERTAINTY.........................................................................................7 5.1. MEASURING INSTRUMENT CALIBRATION............................................................................7 5.2. MEASUREMENT UNCERTAINTY..............................................................................................7 5.3. TEST AND MEASUREMENT EQUIPMENT...............................................................................8 6. SETUP OF EQUIPMENT UNDER TEST.......................................................................................9 7. APPLICABLE RULES....................................................................................................................12 8. TEST SETUP, PROCEDURE AND RESULT..............................................................................15 8.1. 6 dB BANDWIDTH.....................................................................................................................15 8.2. EMISSION BANDWIDTH..........................................................................................................19 8.3. PEAK POWER............................................................................................................................23 8.4. PEAK POWER SPECTRAL DENSITY.......................................................................................27 8.5. MAXIMUM PERMISSIBLE EXPOSURE...................................................................................31 8.6. SPURIOUS EMISSIONS – CONDUCTED MEASUREMENTS.................................................33 8.7. UNDESIRABLE EMISSIONS – RADIATED MEASUREMENTS..............................................39 8.7.1. SETUP AND PROCEDURE..............................................................................................39 8.7.2. TRANSMITTER TEST RESULTS...................................................................................41 8.7.3. DIGITAL DEVICE TEST RESULTS................................................................................51 8.8. POWER LINE CONDUCTED EMISSIONS...............................................................................55 8.9. SETUP PHOTOS........................................................................................................................58 REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 3 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. TEST RESULT CERTIFICATION COMPANY NAME: FHP WIRELESS INC. 1710 SOUTH AMPHLETT BOULEVARD SAN MATEO, CA 94402 USA EUT DESCRIPTION: 802.11B WIRELESS MESHED ROUTER MODEL NUMBER: RP-01-00C-C-N-00, SP-01-00C-C-N-00 DATE TESTED: AUGUST 5 – AUGUST 27, 2002 TYPE OF EQUIPMENT INTENTIONAL RADIATOR EQUIPMENT TYPE 2.4 - 2.4835 GHz TRANSCEIVER, DIGITAL DEVICE MEASUREMENT PROCEDURE ANSI 63.4 / 1992, TIA/EIA 603 PROCEDURE CERTIFICATION FCC RULE CFR 47 PART 15.B AND CFR 47 PART 15.C Compliance Certification Services, Inc. tested the above equipment for compliance with the requirements set forth in CFR 47, PART 15, Subparts B and C. The equipment in the configuration described in this report, shows the measured emission levels emanating from the equipment do not exceed the specified limit. Note: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. Approved & Released For CCS By: Tested By: STEVE CHENG MIKE HECKROTTE EMC ENGINEE…

Text truncated - open the document above for the full version.

REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 58 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8.9. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 59 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TRANSMITTER RADIATED RF MEASUREMENT SETUP WITH PATCH ANTENNA REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 60 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TRANSMITTER RADIATED RF MEASUREMENT SETUP WITH OMNI ANTENNAS REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 61 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE RADIATED EMISSIONS MEASUREMENT SETUP FOR BENCHTOP MOUNTING WITH SELF-CONTAINED POWER REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 62 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE RADIATED EMISSIONS MEASUREMENT SETUP FOR WALL MOUNTING WITH SELF-CONTAINED POWER REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 63 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE RADIATED EMISSIONS MEASUREMENT SETUP FOR BENCHTOP MOUNTING WITH POWER OVER ETHERNET REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 64 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. DIGITAL DEVICE RADIATED EMISSIONS MEASUREMENT SETUP FOR WALL MOUNTING WITH POWER OVER ETHERNET REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 65 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP FOR SELF-CONTAINED POWER REPORT NO: 02U1392-1 DATE: AUGUST 28, 2002 EUT: 802.11a WIRELESS MESHED ROUTER FCC ID: P9JSP-01-00C-C Page 66 of 66 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP FOR POWER OVER ETHERNET END OF REPORT