PD5-WAP150Wireless-AC/N Dual Radio Access Point with PoE

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Quick Start Guide Cisco WAP150 Wireless-AC/N Dual Radio Access Point with PoE 2Cisco WAP150 Quick Start Guide Welcome Thank you for choosing the Cisco WAP150 Wireless-AC/N Dual Radio Access Point with PoE. The Cisco WAP150 is an indoor concurrent dual- band radio 802.11ac and 802.11n access point with Power over Ethernet (PoE). This guide provides the general layout of the Cisco WAP150, describe how to deploy the Cisco WAP150 in your network, and describe how to configure the Cisco WAP150. For additional information, see www.cisco.com/go/100_wap_resources. Package Contents •Wireless Access Point •Power Adapter •This Quick Start Guide •Ethernet Cable •Technical Support Contact •Pointer Card China RoHS •EU Directives 1999/5/EC Compliance Information (for EU SKU only) Before You Begin Before you begin the installation, make sure that you have the following equipment and services: •A computer with browser support for: –Internet Explorer 7.0 or later –Chrome 5.0 or later –Firefox 3.0 or later –Safari 3.0 or later •One or more Ethernet network switches with PoE 1 Cisco WAP150 Quick Start Guide3 Cisco WAP150 Features Front Panel The front panel of the Cisco WAP150 consists of one system LED. For full descriptions of the colors of the lights and their indications, see “Verifying the Hardware Installation”. Back Panel RESET—See “Rebooting the Cisco WAP150 or Resetting to Factory Defaults” for information on the RESET button. LAN (PoE)—The RJ-45 Ethernet port is used to power the Cisco WAP150 using PoE. It is an auto-sensing, Gigabit Ethernet (802.3) port used to connect the Cisco WAP150 to network devices, such as computers, routers, or switches. We strongly recommend that you use a Category 5e or better cable for Gigabit connectivity. POWER—The POWER button is used to turn the power on and off. It is not applicable when using PoE. 12V DC—The 12V DC jack is used to connect the supplied power adapter to the Cisco WAP150 if you are not using PoE. Kensington Lock Slot—The Kensington lock slot is used to attach a cable and lock to the Cisco WAP150. Default Settings If you are using a Cisco RV Series router, the default range for the DHCP assigned address is from 192.168.1.100 to 192.168.1.254. Any device connecting to the same LAN will be assigned an IP address in this range. Mounting the Cisco WAP150 There are two ways to physically install the Cisco WAP150: ParameterDefault Value Usernamecisco Passwordcisco LAN IP AddressDHCP address assigned by server Fallback LAN IP192.168.1.245 Subnetwork Mask255.255.255.0 2 3 4Cisco WAP150 Quick Start Guide •Place the Cisco WAP150 horizontally on a flat surface so that it sits on its four rubber feet. •Mount the Cisco WAP150 to a wall. Wall Mounting The Cisco WAP150 can be wall-mounted using the wall-mount slots on the bottom cover. The wall-mounting hardware is user-supplied. WARNINGInsecure mounting might damage the device or cause injury. Cisco is not responsible for damages incurred by insecure wall- mounting. Placement Tips • Ambient Temperature—To prevent the Cisco WAP150 from overheating, do not operate it in an area that exceeds an ambient temperature of 104°F (40°C). •Air Flow—Be sure there is adequate air flow around the device. • Mechanical Loading—The Cisco WAP150 should be level, stable, and secure to prevent it from sliding or shifting out of position. Connecting the Cisco WAP150 The default configuration of the Cisco WAP150 has the Wi-Fi radio turned on. You can perform the initial configuration using either a wired or wireless connection. To connect the Cisco WAP150 to the wired network: STEP1Connect the Ethernet cable to the Ethernet port of a switch, a router, or a PC. STEP2Connect the other end of the network Ethernet cable to the Ethernet port of the Cisco WAP150. STEP3If PoE is not provided, plug in the supplied power adapter to provide power to the Cisco WAP150. NOTEThe system provides a one-time-only access to configure the access point using a wireless connection. 4 Cisco WAP150 Quick Start Guide5 To connect the Cisco WAP150 to the network wirelessly: STEP1Use FindIt to locate the WAP150’s SSID (CiscoSB-Setup). STEP2Use the ‘cisco123’ passkey to access the access point. After installation, all lights should be active. Refer to “Verifying the Hardware Installation” for details about the different lights on the Cisco WAP150. 6Cisco WAP150 Quick Start Guide Verifying the Hardware Installation To verify the hardware installation, complete the following tasks: •Check the cable connections. •Check the state of the indicator light. NOTEIf you need help resolving a problem, visit the Cisco Support Community at www.cisco.com/go/smallbizsupport. Getting Started with the Configuration To configure the Cisco WAP150, follow these steps to access the web-based Configuration Utility and then the Setup Wizard from your computer: STEP1Connect the Cisco WAP150 to the same network (IP subnet) as your computer. The factory default IP address configuration of the Cisco WAP150 is DHCP. Make sure that your DHCP server is running and can be reached. See “Incorrect IP Address” for troubleshooting information, or if you do not have a DHCP server. STEP2Locate the IP address of the Cisco WAP150. a.The Cisco WAP150 can be accessed and managed by Cisco network tools and services including the Cisco FindIT Network LabelActivityDescription Power OffThe WAP150 is out of power. Solid GreenThe Cisco WAP150 is normal; no wireless client connected. Solid BlueThe Cisco WAP150 is normal; at least one wireless client connected. Solid RedThe Cisco WAP150 fails to boot with both firmware images. Flashing GreenThe Cisco WAP150 is booting. Flashing BlueFirmware upgrade is in progress. LAN OffNo Ethernet link. Solid GreenGigabit Ethernet link is active. Solid AmberFast Ethernet link is active. FlashingTransmitting or receiving data. 5 6 Cisco WAP150 Quick Start Guide7 Discovery Utility that enables you to automatically discover all supported Cisco devices in the same local network …

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

PANTONE BLACK Diecut display only Colors Printed/Dimensions/ LENGTH WIDTH 70 mm x 40.5 mm Models Name/Part Name/ Artwork Number/ Artwork Rev./ Unit:mm SPEC LABEL01 Designed/Date/ 28 Jul. ‘15amyNET15-4057100WAP150-A-R DELTA NETWORKS, INC. THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA NETWORKS. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION . Graphic Layout Scale/ 1:1 Comment/ 0XXX-XX-XXXX (01)XXXXXXXXXXXXXX E134 R-NZ PID VID Model/Modèle:WAP150 Wireless-AC/N Dual Radio Access Point with PoE Point d'accès bibande sans l AC/N avec PoE Input rating/Tension d'entrée: 12Vdc 1.5A PoE (802.3af): 48Vdc 0.35A CAN ICES-3 (B)/NMB-3(B) IC: 3970A-WAP150 FCC ID: PD5-WAP150 This device complies with part 15 FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operations. COMISIóN NACIONAL DE COMUNICACIONES XX-99999

Label location

Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15

Report No.: SA150714C42 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA150714C42 FCC ID: PD5-WAP150 Test Model: WAP150 Received Date: Jul. 15, 2015 Test Date: Jul. 15 ~ Aug. 12, 2015 Issued Date: Aug. 19, 2015 Applicant: Delta Networks, Inc. Address: No. 252, Shanying Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA150714C42 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SA150714C42 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA150714C42 Original release. Aug. 19, 2015 Report No.: SA150714C42 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Wireless-AC/N Dual Radio Access Point with PoE Brand: Cisco Test Model: WAP150 Sample Status: Engineering sample Applicant: Delta Networks, Inc. Test Date: Jul. 15 ~ Aug. 12, 2015 Standards: FCC Part 2 (Section 2.1091) KDB 447498 D03 IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date:Aug. 19, 2015 Pettie Chen / Senior Specialist Approved by : , Date:Aug. 19, 2015 Ken Liu / Senior Manager Report No.: SA150714C42 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA150714C42 Page No. 6 / 6 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 2412-2462 26.37 6.38 20 0.375 1 5180-5240 13.49 6.47 20 0.020 1 5260-5320 18.92 6.70 20 0.073 1 5500-5700 20.04 6.72 20 0.094 1 5745-5825 19.10 6.72 20 0.076 1 Note: 2412-2462MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /2]= 6.38dBi 5180-5240MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /2]= 6.47dBi 5260-5320MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /2]= 6.70dBi 5500-5700MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /2]= 6.72dBi 5745-5825MHz Band: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /2]= 6.72dBi Conclusion: The formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. <…

Text truncated - open the document above for the full version.

Report No.: RF150714C42-1 Page No. 1 / 93 Report Format Version:6.1.1 FCC Test Report Report No.: RF150714C42-1 FCC ID: PD5-WAP150 Test Model: WAP150 Received Date: Jul. 15, 2015 Test Date: Jul. 15 ~ Aug. 12, 2015 Issued Date: Aug. 19, 2015 Applicant: Delta Networks, Inc. Address: No. 252, Shanying Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150714C42-1 Page No. 2 / 93 Report Format Version:6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................ 11 3.3 Duty Cycle of Test Signal .................................................................................................................. 13 3.4 Description of Support Units ............................................................................................................. 14 3.4.1 Configuration of System under Test .................................................................................................. 14 3.5 General Description of Applied Standards ........................................................................................ 15 4 Test Types and Results ...................................................................................................................... 16 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 16 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 16 4.1.2 Test Instruments ................................................................................................................................ 17 4.1.3 Test Procedures ................................................................................................................................. 18 4.1.4 Deviation from Test Standard ............................................................................................................ 18 4.1.5 Test Set Up ........................................................................................................................................ 19 4.1.6 EUT Operating Conditions ................................................................................................................. 20 4.1.7 Test Results ....................................................................................................................................... 21 4.2 Conducted Emission Measurement .................................................................................................. 60 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 60 4.2.2 Test Instruments ................................................................................................................................ 60 4.2.3 Test Procedures ................................................................................................................................. 61 4.2.4 Deviation from Test Standard .................................…

Text truncated - open the document above for the full version.

Report No.: RF150714C42-2 Page No. 1 / 51 Report Format Version:6.1.1 DFS Test Report Report No.: RF150714C42-2 FCC ID: PD5-WAP150 Test Model: WAP150 Received Date: Jul. 15, 2015 Test Date: Aug. 14 ~ Aug. 21, 2015 Issued Date: Aug. 24, 2015 Applicant: Delta Networks, Inc. Address: No. 252, Shanying Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN (R.O.C.) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150714C42-2 Page No. 2 / 51 Report Format Version:6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 EUT Information .................................................................................................................................... 5 2.1 Operating Frequency Bands and Mode of EUT .................................................................................. 5 2.2 EUT Software and Firmware Version .................................................................................................. 5 2.3 Description of Available Antennas to the EUT .................................................................................... 5 2.4 EUT Maximum Conducted Power ....................................................................................................... 6 2.5 EUT Maximum EIRP Power ................................................................................................................ 7 2.6 Transmit Power Control (TPC) ............................................................................................................ 7 2.7 Statement of Maunfacturer .................................................................................................................. 7 3 U-NII DFS Rule Requirements ............................................................................................................. 8 3.1 Working Modes and Required Test Items ........................................................................................... 8 3.2 Test Limits and Radar Signal Parameters ........................................................................................... 9 4 Test & Support Equipment List .......................................................................................................... 11 4.1 Test Instruments ................................................................................................................................. 11 4.2 Description of Support Units .............................................................................................................. 11 5 Test Procedure .................................................................................................................................... 12 5.1 ADT DFS Measurement System ....................................................................................................... 12 5.2 Calibration of DFS detection threshold level ..................................................................................... 13 5.3 Deviation from Test Standard ............................................................................................................ 14 5.4 Radiated Test Setup Configuration ................................................................................................... 14 5.4.1 Master Mode ...................................................................................................................................... 14 5.4.2 Client mode ....................................................................................................................................... 14 6 Test Results ......................................................................................................................................... 15 6.1 Summary of Test Result .................................................................................................................... 15 6.1.1 Master Mode ...................................................................................................................................... 15 6.1.2 Slave without radar detection mode ....................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (Test Mode A) 2 CONDUCTED EMISSION TEST (Test Mode B) 3 RADIATED EMISSION TEST (Above 1GHz) 4 RADIATED EMISSION TEST (Below 1GHz) (Test Mode A) 5 RADIATED EMISSION TEST (Below 1GHz) (Test Mode B)