PD5ARUBA40802.11 b+g Wireless AP

PACKAGE CONTENTS • 1 x Aruba 40 Wireless Access Point • 1 x Quick Installation Guide (this document) Inform your supplier if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them to repack the product in case there is a need to return it. 1 Install two screws in the wall or shelf. If attaching the device to drywall, we recommend using appropriate wall anchors (not included). 2 Align the Aruba 40 mount-ing slots to capture the surface screws. 3 Orient the antenna. For best per-formance, swivel the antenna so that it is oriented vertically. Figure 0-1: Aruba 41 Mounting 10/100 Mbps Ethernet RJ-45 FemalePin-Out *POE UnusedUnusedUnusedUnused 12345678 ETH Rx+ (POE negative*) ETH Rx– (POE negative*) ETH Tx+ (POE positive*) ETH Tx– (POE positive*) Direction Input Output Figure 0-2: Aruba 40 FE Port Aruba 40 Wireless Access Point Quick Installation Guide 2 1 BEFORE GETTING STARTED Before installing your Aruba 40 wirless access point, please ensure you have the following: • 1 x Fast Ethernet cable of required length • 1 x 802.3af compliant Power over Ethernet source (PSE) - Aruba Mobility Controller or Midspan device • 1 x Aruba Mobility Controller provisioned on the network: - with Layer 2/3 network connectivity your Aruba 40 - One of the following network services: - Aruba Discovery Protocol (ADP) - DNS server with an “A” record (see section 1; Provisioning the Aruba 40) - DHCP Server with vendor specifi c options (see section 1; Provisioning the Aruba 40) Optional: • Mounting screws (not supplied) Provisioning using DHCP with Vendor Specific Options A standards compliant DHCP server can be confi gured to return the host Aruba Mobility Controller’s IP address through Vendor Specifi c Options (option 43) in the DHCP reply. If the host Mobility Controller’s IP address is obtained via DHCP, it will be used for uploading the Aruba access point’s software image and confi guration. NOTE: If you have location-specifi c confi gurations for your Access Points, you will need to apply this confi guration information using AP Reprovisioning. AP Reprovisioning Once an AP is associated to an Aruba Mobility Controller, it is capable of being Reprovisioned if necessary. AP Reprovisioning is the process by which APs are assigned unique confi guration characteristics, for example, location codes. Location codes are important for recalibration and triangulation. For details on AP Reprovisioning, see the ArubaOS User Guide. AP Provisioning Recommended only in instances where APs require to be pre-staged or provisioned in advance of shipment and fi nal network installation (suchas as Remote Access Point (RAP) deployments), in AP programming mode, AP confi guration parameters are defi ned on the Aruba Mobility Controller via command line interface or web interface, where they can then be uploaded to individual access points as required. Installing the Aruba 40 Select a location as close as possible to the center of the intend-ed coverage area. The service location should be free from obstructions or obvious sources of interference. Normally, the higher you place an access point or air monitor, the better its per-formance.The Aruba 40 can be mounted on a wall using the mounting slots on the bottom of the unit.NOTE: For dimensions, see “Product Specifi cations” . Allow 5 cm (2”) additional space on the right-hand side for cables and ensure enough space for antenna articulation. Using the Built-In Mounting Slots The keyhole-shaped slots on the back of the Aruba 40 can be used to attach the device upright to an indoor wall or shelf.CAUTION: Do not use the mounting slots to hang the Aruba 40 from the ceiling, sideways, or in any place where it could fall on people or equipment. For more secure installation, use one of the optional mounting kits.To hang the Aruba 40 upright using the mounting slots, perform the following steps: Connecting Required Cables NOTE: Aruba 40 Access Points are intended only for installation in Environment A as defi ned in IEEE 802.3.af, Power over Ethernet. All interconnected equipment must be contained within the same building, including the interconnected equipment’s associ-ated LAN connections.The 10/100 Mbps Ethernet (FE) port is used to connect the AP to a 10Base-T/100Base-TX (twisted-pair) Ethernet LAN segment. Use a 4- or 8-conductor, Category 5 UTP, straight-through FE cable.X and automatically adjusts for straight-through or cross-over cables. The maximum length for FE cables is 100 meters (325 feet). Install cables in accordance with all applicable local and national regulations and practices. Connecting Cables & Power 1 Connect one end of the FE cable directly to the Aruba 40 FE port 2 Connect the other end of the FE cable to one of the following: - To a network port on the Mobility Controller, or - To a network mid-span device that supports 802.3af compliant port FE Port Specifi cations The 10/100 Mbps Ethernet (FE) port is located on the right-hand side of the Aruba 40 and has an RJ-45 female connector. The port pin-outs are shown in Figure 0-2: Verifying Successful Installation The integrated LEDs on the AP 40 may be used at this point to verify the AP is receiving power and initializing successfully. LED behavior indicated status as follows: Configuring the Aruba 40 Once the Aruba 40 has been provisioned and installed, it will be capable of discovery and association to an Aruba Mobility Controller where the wireless and security parameters can be set. For AP confi guration information, refer to the ArubaOS User Guide AAAruArub Installation instructions for the deployment and installation of your Aruba 40 802.11b/g wireless access point. About the Aruba 40 The Aruba 41 is part of a comprehensive wireless network solution. The device works only in conjunction with an Aruba Mobility Controller, and provides the following capabilities: • Wireless transceiver • Protocol-independent networking functionality …

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID : PD5ARUBA40 Label Location

Page 3 Page 4 Page 5 Page 6 Page 7

FCC ID: PD5ARUBA40 Report No. RF940629L11 Operational Description This device is an 802.11 b+g wireless AP which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by POE. The antenna is printed and Dipole antenna with UFL antenna connector. Under normal use condition, the user has to keep at least 20cm separation distance between radiator and the body of the user. The other instruction, please have a look at the users manual.

FCC ID: PD5ARUBA40 Report No: SA940629L11 1 RF EXPOSURE REPORT REPORT NO.: SA940629L11 MODEL NO.: AP40 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Delta Networks, Inc. ADDRESS: 252, Shang Ying Road, Kuei San Taoyuan Shien 333, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: PD5ARUBA40 Report No: SA940629L11 2 RF Exposure Measurement (Mobile Device) 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: PD5ARUBA40 Report No: SA940629L11 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance r. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification This device is not fixed inside the host equipment, it is connected with host through wire. So it is easy to be re-located in the place where at least 20cm far away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device. FCC ID: PD5ARUBA40 Report No: SA940629L11 4 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 1.9dBi or 1.589 (numeric). 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: Dipole antenna gain: 1.9dBi 802.11b DSSS modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241252.360 0.016 1.0 6243751.404 0.016 1.0 11246251.286 0.016 1.0 802.11g OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241245.814 0.014 1.0 6243750.933 0.016 1.0 11246245.920 0.014 1.0 Printed antenna gain: 1.05dBi 802.11b DSSS modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241252.3600.0131.0 6243751.4040.0131.0 11246251.2860.0131.0 802.11g OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241245.8140.0121.0 6243750.9330.0131.0 11246245.9200.0121.0

FCC ID: PD5ARUBA40 Report No.: RF940629L111Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940629L11 MODEL NO.: AP40 RECEIVED: Jun. 30, 2005 TESTED: Jul. 05 ~ 11, 2005 ISSUED: Jul. 13, 2005 APPLICANT: Delta Networks, Inc. ADDRESS: 252,Shang Ying Road,Kuei San Taoyuan Shien 333,Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 62 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: PD5ARUBA40 Report No.: RF940629L112Report Format Version 2.0.2 TABLE OF CONTENTS 1.CERTIFICATION...........................................................................................................4 2.SUMMARY OF TEST RESULTS ..................................................................................5 2.1MEASUREMENT UNCERTAINTY................................................................................5 3.GENERAL INFORMATION ...........................................................................................6 3.1 GENERAL DESCRIPTION OF EUT .............................................................................6 3.2 DESCRIPTION OF TEST MODES ...............................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ..........................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ...............................8 3.2.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................10 3.2.4 DESCRIPTION OF SUPPORT UNITS .......................................................................10 4. TEST TYPES AND RESULTS .................................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT ............................................................. 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 11 4.1.2 TEST INSTRUMENTS................................................................................................ 11 4.1.3 TEST PROCEDURES ................................................................................................12 4.1.4 DEVIATION FROM TEST STANDARD.......................................................................12 4.1.5 TEST SETUP..............................................................................................................13 4.1.6 EUT OPERATING CONDITIONS ...............................................................................13 4.1.7 TEST RESULTS .........................................................................................................14 4.2 RADIATED EMISSION MEASUREMENT ..................................................................20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................20 4.2.2 TEST INSTRUMENTS................................................................................................21 4.2.3 TEST PROCEDURES ................................................................................................22 4.2.4 DEVIATION FROM TEST STANDARD.......................................................................23 4.2.5 TEST SETUP..............................................................................................................23 4.2.6 EUT OPERATING CONDITIONS ...............................................................................23 4.2.7 TEST RESULTS .........................................................................................................24 4.3 6dB BANDWIDTH MEASUREMENT..........................................................................31 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .......................................................31 4.3.2 TEST INSTRUMENTS................................................................................................31 4.3.3 TEST PROCEDURE...................................................................................................32 4.3.4 DEVIATION FROM TEST STANDARD.......................................................................32 4.3.5 TEST SETUP..............................................................................................................32 4.3.6 EUT OPERATING CONDITIONS ...............................................................................32 4.3.7 TEST RESULTS .........................................................................................................33 4.4 MAXIMUM PEAK OUTPUT POWER..........................................................................39 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ..........................39 FCC ID: PD5ARUBA40 Report No.: RF940629L113Report Format Version 2.0.2 4.4.2 INSTRUMENTS..........................................................................................................39 4.4.3 TEST PROCEDURES ................................................................................................40 4.4.4 DEVIATION FROM TEST STANDARD.......................................................................40 4.4.5 TEST SETUP..............................................................................................................40 4.4.6 EUT OPERATING CONDITIONS ...............................................................................40 4.4.7 TEST RESULTS .........................................................................................................41 4.5 POWER SPECTRAL…

Text truncated - open the document above for the full version.

FCC ID: PD5ARUBA40 Report No.: RF940629L1160Report Format Version 2.0.2 5. PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: PD5ARUBA40 Report No.: RF940629L1161Report Format Version 2.0.2 RADIATED EMISSION TEST