PFCIT365IRDigital Satellite Receiver

Graphical Symbol Outdoor Use Warning Marking Polarized Attachment Plug Marking The Lightning flash with arrowhead symbol, within an equilateral triangleis intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance. "WARNING - TO REDUCE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE." "CAUTION : To prevent electric shock, match wide blade of plug to wide slot, full inset." C A U T I O NC A U T I O N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note Safety Instructions Note Note : This equipment has been tested and found to comply with the limit for a Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. If this equipment does cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experience radio TV technician for help. Change or modification not expressly approved by the party responsible for Compliance could void the user's authority to operate the equipment. Safety Instructions 1. Read Instructions : All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions : The safety and operating instruction should e retained for future reference. 3. Head Warning s: All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions : All operation and use instructions should be followed. 5. Cleaning : Unplug this product from the wall outlet before cleaning. Vo not use liquid cleaners or aerosol cleaner. Use a damp cloth for cleaning. Exception : A product that is meant for uninterrupted service and that for some specific reason, such ad the possibility of the loss of and authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the product in the cleaning description otherwise required in this article. 6. Attachment : Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture : Do not use the product near water for example, near a bath wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. Accessories : Do not place this product on an unstable cart, stand, tripod, bracket or table. This product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or tape recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with card. Quick stops, excessive force, and uneven surface may cause the product and cart combination to overturn. 10.Ventilation - Slot and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protest it from overheating and these openings must not be blocked by covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation in provided or the manufacturer's instructions have been adhered to. 11. Power Sources : This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, Safety Instructions 13. Power-Cord Protection : Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Protective Attachment Plug : Te product is equipped with an attachment plug having overload protection. This is a safety feature. See instruction Manual for replacement or resetting or protective device. If replacement plug specified by the manufacturer that vas the same overload protection as the original plug. 15. Outdoor Antenna Grounding : If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electric Code, ANSI/NFPA 70, provides information with regards. Please refer to picture 2 in the end of this chapter. 16. Lighting : For added protection for this product during a lighting storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to …

Text truncated - open the document above for the full version.

FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 Appendix E. Block Diagram ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 1 of 1 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR

Appendix C. External Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 1 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Front View of EUT Right View of EUT Appendix C. External Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 2 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Left side View of EUT Rear side View of EUT Appendix C. External Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 3 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR View of Bottom Cover View of Top Cover Appendix C. External Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 4 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR View of Front Cover

FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 Appendix A. FCC ID Label and Location ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 1 of 2 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Product Label Sample with FCC ID Label information Following is a copy of the label that will be placed on the rear side of the cabinet. Figure 3.1 PRODUCT LABEL Both the FCC ID and compliance statement are included in the product label INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver FCC ID : PFCIT365IR Model NO : IT365IR POWER : AC 90~240V, 50~60Hz, Max. 40W Serial No : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Manufacture: INTEGRA TELECOM Co., Ltd. Made in Korea FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 Appendix A. FCC ID Label and Location ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 2 of 2 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR 1.2 Label Location Photos The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase.(Labeling requirements per 2.925) Label here

Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 1 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Inside View of EUT Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 2 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Component View of Main Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 3 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Solder View of Main Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 4 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Component View of Power Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 5 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Solder View of Power Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 6 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Component View of Front Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 7 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Solder View of Front Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 8 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Component View of SUB Board Appendix D. Internal Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 9 of 9 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Solder View of SUB Board

FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 5 of 26 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR 2.1 Equipment Description The Equipment Under Test(EUT) is the INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model : IT365IR. 2.2 General Specification - Chassis Type : Metal -List of Each OSC. Or X-Tal. Freq.(>=1MHz) : OSC-27MHz, -. Chipset Brand & Part No. : Hynix / HY57V641620HG, OMEGA / J224F0212, ST / M28W160CT, AMK / 4351VT -. RF Modurator Frequendy : CH3(61.25MHz), CH4(67.25MHz) -. RF Modurator Output Chanel : Channel 3 or Channel 4 -. LNB Frequency range : 950MHz ~ 2150MHz -. LNB Signal level : - 65dBm ~ - 25dBm -. LNB Power : 13.5/18.5Vdc 5 , 0.5Amax, Overload protected -. LNB Input Impedance : 75 ohm unbalanced -. LNB DiSEqC Control : Ver 1.2 Compatible -. Demodurator : QPSK -. Demodurator Symbol rate : 2Msps ~ 45Msps -. System Main Processor : Sti5518 -. System resource(SDRAM) : 8Mbyte -. System resource(FLASH) : 2Mbyte -. System resource(EEPROM) : 16Kbyte -. MPEG&A/V Decoding Profile level : MPEG 2(Main Profile @ Main Level) -. MPEG Transport Stream : MPEG-2 ISO/IEC 13818 Transport Stream Specification -. Video Decoder video format : NTSC, PAL -. Video Decoder Resolution : 720 x 576(PAL), 720 x 480(NTSC) -. Audio Decoding : MPEG/MusiCam Layer I & II, MP3, AC3 -. Power Consumption : AC 90~240V, 50~60Hz, max 40W

www.etl.re.kr E-RAE Testing Laboratory This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the ETL,Inc. Electromagnetic Emission FCC MEASUREMENT REPORT CERTIFICATION OF COMPLIANCE FCC Part 15 Certification Measurement This Digital Satellite Receiver Model PANSAT 600IR has been tested in accordance with the measurement procedures specified in ANSI C63.4-1992 at the ETL/EMC Test Laboratory and has been shown to be complied with the electromagnetic radiated emission limits specified in FCC Rule Part15 Subpart B : Unintentional Radiators TV Interface Devices. Including cable system terminal devices I attest to the accuracy of data. All measurement herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Yo Han, Park / Chief Engineer E-RAE Testing Laboratory Inc. #584 Sangwhal-ri, Yoju-kun, Kanam-myon, Kyounggi-do, 469-880, Korea PRODUCT : Digital Satellite Receiver MODEL/TYPE NO : IT365IR FCC ID : PFCIT365IR APPLICANT : INTEGRA TELECOM Co., Ltd 7 th , Hwayoung Bdg., 112-2, Garak-Dong, Songpa-Gu, Seoul, 138-160, Korea Nam Cheol Woo / DVB H/W STI Team, Senior Engineer FCC CLASSIFICATION : Part 15 Class B Unintentional Radiators TV Interface Devices, Including cable system terminal devices FCC RULE PART(S) : FCC Part 15 Subpart B FCC PROCEDURE : Certification TRADE NAME : INTEGRA TEST REPORT No. : E02.1109.FCC.751N DATES OF TEST : November 07~09, 2002 DATES OF ISSUE : November 09, 2002 TEST LABORATORY : ETL Inc ( FCC Registration Number : 95422) #584 Sangwhal-ri, Yoju-kun, Kanam-myon, Kyounggi-do, 469-880, Korea Tel : (031) 885-0072 Fax : (031) 885-0074 FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 2 of 26 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Table of Contents ATTACHMENT A: COVER LETTER(S) FCC Measurement Report 1. Introduction 2. Product Information 3. Description of Tests 4. Test Condition 5. Test Results 5.1 Summary of Test Results 5.2 Conducted Emission Test 5.3 Radiated Emission Test 5.4 Output Signal Level Measurement 5.5 Output Terminal Conducted Spurious Emission Measurement 5.6 Transfer Switch Measurement 6. Sample Calculations 7. List of test Equipment used for Measurement Appendix A. FCC ID Label and Location Appendix B. Test Setup Photographs Appendix C. External Photographs Appendix D. Internal Photographs Appendix E. Block Diagram Appendix F. User’s Manual FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 3 of 26 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR FCC MEASUREMENT REPORT Scope – Measurement and determination of electromagnetic emission(EME) of radio frequency devices including intentional radiators and/or unintentional radiators for compliance with the technical rules and regulations of the U.S Federal Communications Commission(FCC) General Information l EUT Type : Digital Satellite Receiver l Model Number : IT365IR l FCC Identifier : PFCIT365IR l S/N : N/A l Freq. Range : 60 MHz – 72 MHz l FCC Rule Part(s) : Part 15 Subpart B Section 15.115 l Test Procedure : ANSI C63.4-1992 l FCC Classification : TV Interface Device(HID) l RF Channels : Ch. 3 / Ch. 4 l Dates of Tests : November 07~09, 2002 l Place of Tests : ETL Inc 584, Sangwhal-Ri, Kanam-Myun, Yoju-Kun, Kyounggi-Do, Korea Tel : (031) 885-0072 Fax : (031) 885-0074 l Test Report No. : E02.1109.FCC.751N Applicant Name : INTEGRA TELECOM Co.,Ltd. Address : 7 th , Hwayoung Bdg., 112-2, Garak-Dong, Songpa-Gu, Seoul, 138-160, Korea Attention : Nam Cheol Woo / DVB H/W STI Team, Senior Engineer FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 4 of 26 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR The measurement test for radiated and conducted emission test were conducted at the open area test site of E- RAE Testing Laboratiry Inc. facility located at 584, Sangwhal-ri, Ganam-myun, Youju-kun, Kyoungki-do, Korea. The site is constructed in conformance with the requirements of the ANSI C63.4-1992 and CISPR Publication 16. The ETL has site descriptions on file with the FCC for 3 and 10 meter site configurations. Detailed description of test facility was found to be in compliance with the requirements of Section 2.948 FCC Rules according to the ANSI C63.4-1992 and registered to the Federal Communications Commission(Registration Number : 95422 ). The measurement procedure described in American National Standard for Method of Measurement of Radio-Noise Emission from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSI C.63.4- 1992) was used in determining radiated and conducted emissions from the INTEGRA TELECOM Co.,Ltd. Digital Satellite Receiver Model : IT365IR. FCC ID: PFCIT365IR Report No: E02.1109.FCC.751N Test Date: November 07~09, 2002 ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea. 5 of 26 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR 2.1 Equipment Description The Equipment Under Test(EUT) is the INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model : IT365IR. 2.2 General Specification - Chassis Type : Metal -List of Each OSC. Or X-Tal. Freq.(>=1MHz) : OSC-27MHz, -. Chipset Brand & Part No. : Hynix / HY57V641620HG, OMEGA / J224F0212, ST / M28W160CT, AMK / 4351VT -. RF Modurator Fr…

Text truncated - open the document above for the full version.

Appendix B. Test Setup Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea.1 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Radiated Emission Test Setup Appendix B. Test Setup Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea.2 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Conducted Emission Test Setup Appendix B. Test Setup Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea.3 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Output Signal Level Measurement Setup Output Terminal Conducted Spurious Measurement Setup Appendix B. Test Setup Photographs ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-880,Korea.4 of 4 FCC ID : PFCIT365IR Report No: E02.1109.FCC.751N Date of Test: November 07~09, 2002 INTEGRA TELECOM Co., Ltd. Digital Satellite Receiver Model: IT365IR Transfer Switch Measurement Setup Antenna Power Conduction Measurement Setup