PKG07159RC27Remote Control

The packaging and instruction manual contain important information. Please keep them for future reference. Contents: RC vehicle x 1 RC transmitter x 1 Instruction manual x 1 Transmitter antenna x 1 Battery Requirement : Vehicle : Built in 1.2V rechargable battery (non-replaceable). Transmitter : 2 x 1.5V "AA" / LR6 alkaline batteries (not included). Transmitter: Battery and Antenna Installation 1. Open the battery cover using a screwdrive (not included). 2. 3. Fasten the battery cover. 4. Screw the antenna into the transmitter securely. Vehicle: Battery charging 1. Switch OFF the vehicle. 2. Park and plug the car into the charging terminal of the transmitter 3. HOW TO PLAY : 1. Switch ON the vehicle. 2. Drive the vehicle forwards and backwards by pressing the FORWARD and BACKWARD buttons respectively. 3. Turn the transmitter steering wheel to move the vehicle left or right. 4. If the vehicle does not run in a straight line, adjust the wheel alignment lever on the vehicle chassis. 5. Remember to switch OFF the vehicle power after playing. Performance Tips: 1. Do not drive on grass, dirt, sand, carpet or go through water. 2. Do not drive in windy or rainy weather. 3. Avoid direct impact with obstacles. 4. Switch off the vehicle when not in use. 5. Keep fingers, hair and loose clothing away from the wheels. 6. The operating range can be affected by a variety of factors: a) weak transmitter's or vehicle's batteries. BATTERY USE Maisto Radio Control Vehicles Install two new AA 1.5V batteries with correct polarity (+/-) as shown inside the battery compartment. A red LED indicator on the transmitter lights up during charging. The charging cycle complete when the indicator turns off b) Interference from other items that emit radio frequency signals such as another R/C item on the same frequency, CB radios, cordless phones, high voltage transformers, etc. 1. Alkaline batteries are recommended to use. 2. Only batteries of the same or equivalent type as recommended are to be used. 3. Do not mix alkaline, standard or rechargeable batteries. 4. Do not mix old and new batteries or different type of batteries. 5. Non-rechargeable batteries are not to be charged. 6. If rechargeable batteries are used, they are only to be charged under adult supervision. 7. Rechargeable batteries are to be removed from the product before they are charged. 8. Be sure to insert batteries with the correct polarities and always follow the battery manufacturer's instructions. 9. Remove all batteries from the transmitter when not in use. 10. Exhausted batteries are to be removed from the product. 11. The supply terminals are not to be short-circuited. CAUTIONS 1. Do not attempt to disassemble the products. 2. 3. Make sure the batteries are Installed with correct polarity (+/-) as shown inside the battery compartment. FCC Label Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions : 1. This device may not cause harmful interference, and 2. RSS-310 Compliance Statement : This radiocommunication device complies with all the requirements of Industry Canada Standard RSS-310. TROUBLE SHOOTING ProblemCauseCorrection No FunctionLow battery levelReplace with new batteries Battery polarities are reversed Insert the batteries with correct polarities as shown on the battery compartment The wheels are obstructed by foreign objectsRemove foreign objects on the vehicle / wheels Drive Slow /Low battery levelReplace with new batteries Poor Turning SignalThe wheels are obstructed by foreign objectsRemove foreign objects on the vehicle / wheels Poor distance controlLow battery levelReplace with new batteries Strong interference of surroundingsMove to a better location for playing WARRANTY The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the User's Authority to operate the equipment. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. All Maisto R/C vehicles have a 30 day limited warranty in function and performance. You may receive a new replacement vehicle if the defective vehicle is returned to Maisto freight prepaid and confirmed to be factory defective. We are not responsible for defects due to abusive use, or damaged for reasons other than factory defects. We also reserve the right to make the final judgment and decision. Check the FAQ section before you return the unit to Maisto. 12. Dispose of batteries properly. Do not dispose the batteries in fire — it may cause them to explode or leak causing injury or damage. Do not operate the vehicle with same frequency with other players in same location that will interfere and make the vehicle out of control. This device must accept any interference received, including interference that may cause undesired operatio Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit diffe…

Text truncated - open the document above for the full version.

Report No.SZEE071222113304 Page 14 of 15 7.APPENDIX 2 PHOTOGRAPHS OF EUT TOP VIEW OF SAMPLE BOTTOM VIEW OF SAMPLE

FCC ID:PKG07159RC27 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. didi

Label location

INTERNAL PHOTO 1 OF TX INTERNAL PHOTO 2 OF TX

Model:07159 27 MHZ Operation Description The IC1 reads output commands and encodes. the codes are sent to RF oscillator, and then modulates 27MHZ carry frequency signal to achieve AM signal. The radio frequency of the transmitter is based on 27MHZ AM citizen's band. It generates low power 27.145MHZ carrier frequency via major components of Q1,X1 etc. Please note that the value of the component and see attached schematics for more detail. The AM signal(Via capacitor C9)is passed to the antenna(ANT) via components.

Report No.SZEE071222113304 Page 1 of 15 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART15C REQUIREMENT OF 20-07159 Remote control (TX) MODEL No.: 20-07159 BRAND NAME: N/A FCC ID:PKG07159RC27 REPORT NO.: SZEE071222113304 ISSUE DATE: January 2, 2008 Prepared for MAY CHEONG TOY PRODUCTS FTY LTD 12/F,EMPIRE CENTRE,68 MODY ROAD,TSIMSHATSUI EAST,KOWLOON,HONGKONG TEL: 86-769-8775 3128 FAX: 86-769-8775 3123 Prepared by CENTRE TESTING INTERNATIONAL 1F., BUILDING C,HONGWEI INDUSTRIAL ZONE, BAOAN 70 DISTRICT, SHENZHEN, CHINA TEL: 86-755-3368 3668 FAX: 86-755-3368 3385 This report shall not be reproduced, except in full, without the written approval of CENTRE TESTING INTERNATIONAL Report No.SZEE071222113304 Page 2 of 15 Report No.SZEE071222113304 Page 3 of 15 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .................................................................................................. 4 1.1PRODUCT DESCRIPTION........................................................................................................................4 1.2TEST METHODOLOGY...........................................................................................................................4 1.3TEST FACILITY.....................................................................................................................................4 1.4 SPECIAL ACCESSORIES........................................................................................................................4 1.5 EQUIPMENT MODIFICATIONS..............................................................................................................4 2. SYSTEM TEST CONFIGURATION ..................................................................................... 5 2.1 EUT CONFIGURATION.........................................................................................................................5 2.2 EUT EXERCISE....................................................................................................................................5 2.3TEST PROCEDURE.................................................................................................................................5 2.4LIMITATION..........................................................................................................................................6 2.5CONFIGURATION OF TEST SETUP..........................................................................................................7 3. SUMMARY OF TEST RESULTS .......................................................................................... 7 4. DESCRIPTION OF TEST MODES ....................................................................................... 7 5. RADIATED EMISSION TEST ............................................................................................... 8 5.1MEASUREMENT PROCEDURE................................................................................................................8 5.2TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ......................................................................9 5.3MEASUREMENT EQUIPMENT USED: ...................................................................................................10 5.4FIELD STRENGTH CALCULATION.......................................................................................................10 5.5MEASUREMENT RESULT.....................................................................................................................11 6.APPENDIX 1 PHOTOGRAPHS OF SETUP ....................................................................... 13 7.APPENDIX 2 PHOTOGRAPHS OF EUT ............................................................................ 14 Report No.SZEE071222113304 Page 4 of 15 1. GENERAL INFORMATION 1.1 Product Description The TRANSMITTER. Model: 20-07159(referred to as the EUT in this report) The EUT is an short range, lower power, 20-07159 Remote control designed as an “ Input Device”. It is designed by way of utilizing the FSK modulation achieves the system operating. A major technical descriptions of EUT is described as following: A). Operation Frequency: 27.145 MHz ,one channel. B). Modulation: FSK C). Antenna Designation: integral antenna (it can’t be moved during the test) D). Power Supply: DC3 V by battery. 1.2 Test Methodology Both conducted and radiated testing were performed according to the procedures in ANSI C63.4 (2003). Radiated testing was performed at an antenna to EUT distance 3 meters. 1.3 Test Facility The 3m Semi-Anechoic chamber test site and conducted measurement facility used to collect the radiated data is located on the address: 1F.,Building C, Hongwei Industrial Zone 70District.,Baoan,Shenzhen,Guangdong,China . The Test Sites and the Line Conducted labs are constructed and calibrated to meet the FCC requirements in documents ANSI C63.4: 2003 requirements. The test site Registration Number:614926 1.4 Special Accessories Not available for this EUT intended for grant. 1.5 Equipment Modifications Not available for this EUT intended for grant. Report No.SZEE071222113304 Page 5 of 15 2. System Test Configuration 2.1 EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. 2.2 EUT Exercise The Transmitter was operated in the normal operating mode. the TX frequency was fixed which was for the purpose of the measurements. 2.3 Test Procedure 2.3.1 Conducted Emissions (Not apply in the report) The EUT is a placed on as turn table which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4-2003.Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-Peak and average detector mode. 2.3.2 Radiated Emissions The EUT i…

Text truncated - open the document above for the full version.

SETUP PHOTO