PKG82861RC1 16 RC Ferrari 499P

English Age 8+ 2.4GHz R/C Contents: Maisto - Radio Control Vehicles Please keep this owner’s instruction manual for future reference. It contains important information. We reserve the right to improve/revise the product specifications without notice. Class 1 LED Product • RC Vehicle With Built-in Rechargeable Battery (non replaceable) x 1 • Controller x 1 • 1.5V "AAA" LR03/R03 non-rechargeable Battery (For Controller Use) x 2 • USB Cable x 1 • Owner’s Instruction Manual x 1 Charging the built-in rechargeable battery for the RC vehicle: (Refer to Diagram 1) 1. Open the charging port cover on the vehicle. 2. Make sure the switch is on the OFF/CHARGE position befor charging. 3. Locate a USB certified port from any of the devices shown below. 4. Connect the USB charging plug with the USB certified port. 5. The LED indicator will start lighting in red to show it is charging. 6. Once the LED indicator turns off, the vehicle is fully charged. 7. Detach the USB plug from the USB certified port, then install the charging port cover on the vehicle. Battery installation for the controller: (Refer to Diagram 2) 1. Switch the power OFF. 2. Use screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included) 3. Install 2 new 1.5V "AAA" LR03/R03 batteries with correct polarity (+/-) as shown inside the battery compartment. 4. Install the battery cover and then tighten the screw on the battery cover. How to play: (Refer to Diagram 3, 4 & 5) 1. Set the "Power Switch" on the controller and vehicle to ON position, the "Power LED" on the vehicle will flash less than 3 seconds then stay on, meaning the automatic frequency matching between the controller and the vehicle is completed. English 2. If the "Power LED" of the vehicle flash more than 3 seconds, switch off both the vehicle and controller, then turn them on again. 3. Pull the trigger on the transmitter to drive the vehicle forward. Push the trigger on the transmitter to drive the vehicle backward. 4. The headlights will light up when the vehicle is moving forward. 5. Turn the transmitter steering wheel to move the vehicle left or right. 6. If the vehicle does not run in a straight line, adjust the wheel alignment under the chassis. 7. The “Power LED” on the vehicle will not flash nor stay on if the rechargeable battery has run out power. 8. Turn the switch of the controller and vehicle to OFF position when not in play. Performance Tips: 1. Do not drive the vehicle on grass, sand or go through water. 2. Do not drive the vehicle in windy or rainy weather. 3. Do not drive the vehicle into any hard object. 4. Keep fingers, hair and loose clothing away from the vehicle. 5. The operating range can be affected by a variety of factors: a) Weak controller or vehicle batteries. b) Interference from other items that emit radio frequency signals such as another R/C item on the same frequency, CB radios, cordless phones, high voltage transmitter, etc. 6. Outdoor usage is recommended in order to get optimal control range. 7. Remove the package, take out all accessories and assemble the product before giving it to children to play. Cautions: 1. The Built-in rechargeable battery must be charged before use. 2. Do not overcharge the Battery. 3. Do not charge the Battery if it shows leakage, corrosion, or has loose or exposed wires or other damage. 4. Do not cover the vehicle with any sort of material while charging. EnglishEnglish 5. Do not touch the vehicle when it is hot. Wait until the vehicle cools before recharging. 6. Do not dispose of the Battery in fire. 7. Do not dismantle the Battery or USB, and do not cut the Battery or USB cables. 8. The USB Cable used with the toy shall be regularly examined for damage to the cord, plug, enclosure and other parts, and in the event of such damage, they must not be used until the damage has been repaired. 9. Rechargeable batteries are to be removed from the toy before being charged (for transmitter). 10.The Battery will be warm after charging, and hot after use in a Vehicle. 11.The supply terminals are not to be short-circuited. 12. Rechargeable batteries are only to be charged by adults or by children at least 8 years old. 13.Battery change must only be made by adults! 14. Note that the 1.5V "AAA" Battery is non-rechargeable and is not to be recharged. Only Batteries of the same or equivalent type as recommended are to be used. It will need replacement when transmission is poor. Alkaline AAA batteries are recommended to be used for the transmitter. Do not mix alkaline,standard or rechargeable batteries. Do not mix old and new batteries or different type of batteries. Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions. 15.Exhausted batteries must be removed from the product. FCC Label Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions : 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and …

Text truncated - open the document above for the full version.

Form:RFT-AMER-TCB-OP-19oRevision:1Page 1 of 1 Date:1/25/2023 MayCheongToyProductsFty.Ltd. Attention:ApplicationExaminer Re:CertificationdesignatingaU.S.agentforserviceofprocesspursuanttosection2.911(d)(7)oftheFCC rules Towhomitmayconcern, Thisletteristoconfirmboth[MaistoInternational,Inc.](“Agent”)and[ MayCheongToyProductsFty.Ltd. ] (“Applicant”)acknowledgeconsenttoobligationsofeachpartypursuantto47CFRpart§2.911(d)(7)ofthe FCCrulesinregardtotheagentforserviceofprocess. I[AnsonWang]HEREBYCERTIFYTHATIamauthorizedtomaketherepresentationsaboveonbehalfof theApplicant.Ifurtheracknowledgetherequirementtomaintainanagentextendsfornolessthanoneyear aftertheterminationofallmarketingandimportationortheconclusionofandcommission-relatedproceeding involvingtheequipmentandagreetoimmediatelynotifytheFCCandIntertekifthereisanychangeinthe statusidentifiedabove. Applicant CompanyName:MayCheongToyProductsFty.Ltd. ContactName:AnsonWang Address :Unit901-2,9/F.,EastOceanCentre,98GranvilleRoad,TsimshatsuiEast,Kowloon,Hong Kong TelephoneNo:(852)27937800 Email:[email protected] FCCID:PKG82861RC ApplicantFRN:0014491856 Signature:____________________________________ Date:Apr18,2024 IJaneMeidtHEREBYCERTIFYTHATIamauthorizedtomaketherepresentationsaboveonbehalfofthe Agent.IconsenttotheobligationtoacceptserviceofprocessonbehalfoftheapplicantinregardtotheFCC IDdesignatedabove. Agent CompanyName:MaistoInternational,Inc. ContactName: JaneMeidt Address:7751CherryAvenue,Fontana,CA92336,U.S.A. TelephoneNo:(909)357-7988 Email:[email protected] AgentFRN:0033602665 Signature:____________________________________ Date:Apr18,2024

Form:RFT-AMER-TCB-OP-19nRevision:1Page 1 of 1 Date:1/25/2023 MayCheongToyProductsFtyLtd Attention:ApplicationExaminer Re:CoveredList,locatedathttps://www.fcc.gov/supplychain/coveredlistand47CFRparts§2.903and §2.911(d)(5)(ii)oftheFCCrules Applicant:[MayCheongToyProductsFtyLtd] FCCID:PKG82861RC Towhomitmayconcern, [MayCheongToyProductsFtyLtd](“Applicant”)certifiesthattheequipmentforwhichauthorizationis soughtisnot“covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuantto47CFR part§2.903oftheFCCrulesanddoesnotoriginatedirectlyorindirectlyfromanycompanynamedonthe coveredlistlocatedinthelinkaboveoranysubsidiaryoraffiliatethereof. Applicantfurthercertifiesthat,asofthedateofthefilingoftheapplication,theApplicant[isnot]identified ontheCoveredListasanentityproducing“covered”equipmentandisnotasubsidiaryoraffiliateofany suchentitypursuantto47CFRpart§1.50002andrequiredby47CFRpart§2.911(d)(5)(ii)oftheFCCrules. IHEREBYCERTIFYTHATIamauthorizedtomaketherepresentationsaboveonbehalfoftheApplicant andagreetoimmediatelynotifyIntertekifthereisanychangeinthestatusidentifiedabove. ______________________________ [SignatureofauthorizedProprietor,PartnerorAuthorizedOfficer] [PrintedName]AnsonWang [Title]QAMANAGER [Companyname]MayCheongToyProductsFtyLtd [Date]Apr18,2024

MayCheongToyProductsFty.Ltd. Apr18,2024 FederalCommunicationsCommission 44512 th StreetSW Washington,DC20554 Subject:LimitedAgencyAgreement MayCheongToyProductsFty.Ltd. FCCID: PKG82861RC ToWhomItMayConcern: We,MayCheongToyProductsFty.Ltd.,herebyauthorizedIntertek TestingServicestoactasourAgentforthepurposeofpreparingapplicationforFCC IDnumber PKG82861RC underallapplicablepartsoftheFCCrulesandregulations. Theeffectivedateofthislimitedagencyagreementis Apr18,2024 .TheLimited AgencyAgreementexpireson Apr17,2025, unlesssoonerterminatedorextendedby writtennoticetoIntertekTestingServicesandtheFederalCommunications Commission. ThisistoadvisethatweareinfullcompliancewiththeAnti-DrugAbuseAct.The applicantisnotsubjecttoadenialoffederalbenefitspursuanttoSection5301ofthe Anti-DrugActof1988,21U.S.C.862,andnopartytotheapplicationissubjecttoa denialoffederalbenefitspursuanttothatsection. Ifyouhaveanyquestionsorcomments,pleasedonothesitatetocontactme. Sincerely, AnsonWang QAMANAGER

MayCheongToyProductsFtyLtd Attention:Certificationreviewer RE:RequestforConfidentiality FCCID:PKG82861RC ToWhomItMayConcern: PermanentConfidentiality[Completethissectionifpermanentconfidentialityis requested] Requesttowithholdpermanentlyfrompublicreviewcertainportionsoftheapplicationfor equipmentcertificationforthereferencedFCCidentifiers.Thisrequestforconfidentialityis madepursuantto47CFR0.457(d)and0.459oftheFCCRules.Inparticular,thefollowing sectionsoftheapplicationaretobekeptpermanentlyconfidential: [Selectoneormoreofitemsbelow,asappropriate,anddeleteunselectedparts] Schematics BlockDiagrams OperationalDescription InternalPhotos(seenote) UsersManual(seenote) Note1:InternalPhotosmaybeheldconfidential1)ifthecircuitboardorinternalcomponentsarenot accessibletousers.Forexample,itisacceptableifthecircuitboardisenclosedinepoxy.2)Also,it isacceptableifthedeviceisnotaccessibletothepublic,forexample,adevicemountedonthetop ofalargetower(orinafencedenclosure)suchthatitisonlyserviceablebyprofessionaldesignated techniciansunderaNon-DisclosureAgreement(NDA).Allsalesforthesedevicesmustbeundera NDArestrictingthedisclosureoftheproprietyinformation,includinginternalphotos. UsersManualmaybeheldconfidentialonlywhenthemanualcontainsproprietarytechnical informationintendedforprofessionaltechniciansobligatedunderaNDA.Allsalesanddistributionof theuser’smanualmustbeunderaNDAthatrestrictsthedisclosureoftheinformation. Intheapplicationcoverletterrequestingpermanentconfidentialitythefollowingadditional descriptionandtheNDAexhibitisrequired: 1.Describeindetailhowinternalphotosand/orusersmanualinformationarecontrolledtoprevent themfrombecomingpublicordisclosedtounauthorizedpersons. 2.Describehowpublicaccessisrestrictedforproductsserviceablebyprofessionaldesignated technicians. 3.Astatementthatallsalesofthenon-consumerdevicewillbeunderaNDAtoincludethirdparty salesandthatthefinaluserofthedeviceissubjecttotheNDA. 4.ProvideanexampleoftheNDAbetweenthegranteeandapurchaser.Therequestfor confidentialitymust Note2:Forscanningreceiver,theschematics,blockdiagrams,operationaldescription,tune-upprocedure, partslistandinternalphotosarealways heldpermanentlyconfidential. Rationaleforrequestforconfidentiality: Wehaveinvestedconsiderabletimeandmaterialsinresearchanddevelopmenttoproduce thereferencedproduct. Permanentconfidentiality:Disclosureofthepermanentlyconfidentialportionsofthis applicationtocompetitorswouldnotonlygivethemsignificantcompetitiveadvantagesin developingsimilarproducts,butwouldalsodisclosesuccessfulimplementationof unpublished,leadingedgetechnologydevelopedbyus. Ifyouhavequestionsorneedfurtherinformation,pleasecontacttheundersigned. Sincerely, [Nameoftheapplicant/granteecontactofFCC] [Title]QAMANAGER [Date]Apr18,2024 AnsonWang

Page 1 of 2 External Photos Page 2 of 2

Label Artwork and Location Size: 45mm(W)X20mm(H)

Page 1 of 3 Internal Photos Page 2 of 3 Page 3 of 3

1 INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is a 1:16 RC Ferrari 499P operating at 2.4G Band. The EUT can be powered by DC 6.4V (1 x 6.4V rechargeable battery). Once use the USB cable charging to the EUT, the wireless function will be disabled. For more detail information pls. refer to the user manual. Antenna Type: Integral antenna. Antenna Gain: 0dBi. The normal radiated output power (e.i.r.p) is: -2.0dBm (tolerance: +/- 3dB). The normal conducted output power is -2.0dBm (tolerance: +/- 3dB). Modulation Type: GFSK. According to the KDB 447498 V06: The Maximum peak radiated emission for the EUT is 94.5 dBμV/m at 3m in the frequency 2420MHz The EIRP = [(FS*D) ^2 / 30] mW = -0.73dBm which is within the production variation. The Minimum peak radiated emission for the EUT is 93.6 dBμV/m at 3m in the frequency 2462MHz The EIRP = [(FS*D) ^2 / 30] mW = -1.63dBm which is within the production variation. The maximum conducted output power specified is 1dBm= 1.259mW The source- based time-averaging conducted output power =1.259mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.462) mW = 9.54 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: PKG82861RC

May Cheong Toy Products Fty. Ltd. TEST REPORT SCOPE OF WORK FCC TESTING– MODEL:23068/82861 REPORTNUMBER GZHH00536405-001 ISSUE DATE MAY 27, 2024 PAGES 24 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.:GZHH00536405-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Service Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page:1 of 24 FCC ID 249_C Test Report May Cheong Toy Products Fty. Ltd. Application for Certification FCC ID: PKG82861RC 1:16 RC Ferrari 499P Additional Name: 1:16 RC Ferrari 296 GT3 / 1:16 RC Alpine A242 Model: 23068/82861 Additional Models: 82862/82863 2.4GHz Transceiver Report No.: GZHH00536405-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-23] Prepared and Checked by: Approved by: Sign on file Terry Tang Assistant Supervisor Ryan Chen Project Engineer Date: May 27, 2024 Intertek Report No.:GZHH00536405-001 Version: 01-November-2017 Page:2 of 24 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-23 Edition] provision. Report prepared by: Terry Tang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel / Fax: 86-755-86016288/86-755-86016751 Intertek Report No.:GZHH00536405-001 Version: 01-November-2017 Page:3 of 24 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ..................................................................................... 4 2.0 General Description ............................................................................................ 5 2.1Product Description ............................................................................................. 5 2.2Related Submittal(s) Grants ................................................................................ 5 2.3Test Methodology ................................................................................................ 5 2.4Test Facility ........................................................................................................ 5 3.0 System Test Configuration ................................................................................. 6 3.1 Justification ........................................................................................................ 6 3.2EUT Exercising Software ..................................................................................... 6 3.3Special Accessories ............................................................................................ 6 3.4Equipment Modification ....................................................................................... 6 3.5 Measurement Uncertainty .................................................................................. 6 3.6 Support Equipment List and Description ............................................................. 6 4.0Emission Results ................................................................................................. 7 4.1 Radiated Test Results ........................................................................................ 7 4.1.1 Field Strength Calculation ................................................................................ 7 4.1.2 Radiated Emission Configuration Photograph .................................................. 8 4.1.3Radiated Emissions .......................................................................................... 8 4.1.4 Transmitter Spurious Emissions .................................................................... 11 5.0 Equipment Photographs ................................................................................... 15 6.0Product Labelling ............................................................................................... 15 7.0Technical Specifications .................................................................................... 15 8.0Instruction Manual ............................................................................................. 15 9.0Miscellaneous Information ................................................................................ 16 9.1 Bandedge Plot ................................................................................................. 16 9.220dB Bandwidth ...…

Text truncated - open the document above for the full version.

Page 1 of 2 Radiated Photos Up to 1GHz (The EUT placed at the center of the turntable) Page 2 of 2 Above 1GHz (The EUT placed at the center of the turntable)