PQN66807RX2G4R1MJC RDC Megalodon Storm GEN 1pk SLD(MCU ABE2402X1)

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both [Spin Master INC] (“Agent”) and [Spin Master Toys Far East Ltd.] (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I [Tommy So] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : Spin Master Toys Far East Ltd. Contact Name : Tommy So Address : Room 1113, 11/F., Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui Telephone No Email FCC ID: Applicant FRN East, Kowloon, Hong Kong : +852 21704124 : [email protected] : PQN66807RX2G4R1 : 0034107417 Signature: ___Tommy So_________________________________ Date: ___Mar 5 th , 2024_________________________________ I [Laurel Roney] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to all certification applications to the FCC submitted by above applicant and agree to immediately notify the FCC and Intertek if there is change in this representation. Agent Company Name : Spin Master INC Contact Name : Laurel Roney Address : 5880 Jefferson Blvd A, Los Angeles, CALIFORNIA, 90016,USA Telephone No : +1 757-318-6302 Email : [email protected] Agent FRN : 0033559402 Signature: ___Laurel Roney_________________________________ Date: ___Mar 5 th , 2024_________________________________

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: Spin Master Toys Far East Ltd. FCC ID: PQN66807RX2G4R1 To whom it may concern, Spin Master Toys Far East Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ [Signature of authorized Proprietor, Partner or Authorized Officer] Mr. Tommy So Senior QA Manager Spin Master Toys Far East Ltd. 4 June 2024

Dec 2013 "I, an officer of (Spin Master Toys Far East Ltd.) do hereby authorize Intertek Testing Services (Mr. Herbert Wong / Jess Tang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules until further notice." I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862. Dated this August 4th of 2023__ By Signature Tommy So Printed Name Senior QA Manager Title Remark: The person who signs this authorization letter must be the grantee contact of record in the Grantee Code data base.

1(2) 2023-08-28 Attention: Application Examiner RE: Request for Confidentiality Applicant: [Spin Master Toys Far East LTD. ] FCC ID: [PQN66807RX2G4R1] To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted by Spin Master Toys Far East LTD. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate]  Schematics  Detailed Block Diagrams  Detailed Operational/Functional Description Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request is hereby submitted by Spin Master Toys Far East LTD. to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization: [Select one or more of items below that are not selected in the list above, as appropriate]  Test setup photos  External photos (NOTE: External photos can only be held for short-term confidentiality)  Internal photos  User manual Rationale for request for confidentiality: [Spin Master Toys Far East LTD. ] has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in 2(2) developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] If you have questions or need further information, please contact the undersigned. Sincerely, [Type Name]Tommy So [Type Title] Manager, Quality [Company name] Spin Master Toys Far East LTD.

Analysis Report The Equipment Under Test (EUT), is a portable 2.4GHz Transceiver (Car Unit) for a RC Car. The sample supplied operated on 46 channels, normally at 2420 - 2465MHz. The channels are separated with 1MHz spacing. The EUT is powered by 2 x 3.2V Lithium-ion batteries. After switching on the EUT, the car will be moved forward or backward and turned left and right based on the switches pressed in the controller. Antenna Type: Internal integral antenna Antenna Gain: 0dBi Nominal rated field strength: 75.0dBμV/m at 3m (Average) Maximum allowed field strength of production tolerance: +/- 3dB According to the KDB 447498 D04 Interim General RF Exposure Guidance v01 Based on the Maximum allowed average field strength of production tolerance was 78.0dBμV/m at 3m. Thus, it below calculated field strength according to minimum SAR exclusion threshold level as follows: The worst case of SAR Exclusion Threshold Level at 2.48GHz with distance 5mm: = 2.717mW According to the KDB 412172 D01: EIRP = [(FS*D) ^2*1000 / 30] Calculated Field Strength for 2.717mW is 99.6dBuV/m @3m Since maximum average field strength plus production tolerance < = 99.6dBuV/m @3m and antenna gain is > = 0.0dBi, it is concluded that maximum Conducted Power and Field Strength are well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

TEST REPORT 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 19 Report No.: 23070019HKG‐003R1 Spin Master Toys Far East Ltd. Application For Certification (Original Grant) Transceiver ‐ 2.4GHz RC Car FCC ID: PQN66807RX2G4R1 This report supersedes previous report with report number 23070019HKG‐003 dated January 16, 2024. Prepared and Checked by: Approved by: Signed on File Leung Chun Ning, Peter Tang Kwan Mo, Jess Assistant Engineer Lead Engineer Date: January 31, 2024 TEST REPORT Spin Master Toys Far East Ltd. Intertek Report No: 23070019HKG‐003R1 Page 2 of 19 GENERAL INFORMATION Grantee: Spin Master Toys Far East Ltd. Grantee Address: Room 1113, 11/F., Chinachem Golden Plaza, 77 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong. FCC ID: PQN66807RX2G4R1 FCC Model: 66807RX Additional Model: 6056226, 6056227, 6061205, 6068252, 1074305, 1074306, 1079835, 1088347 Type of EUT: Transceiver Description of EUT: MJC RDC Megalodon Storm GEN 1pk SLD(MCU ABE2402X1) Brand Name: MJC RDC Megalodon Storm Vehicle Serial Number: N/A Phantom No.: 20122968 Sample Receipt Date: July 03, 2023 Date of Test: July 11, 2023 to July 12, 2023 Report Date: January 31, 2024 Environmental Conditions: Temperature: +10 to 40°C Relative Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 Certification. AMENDMENT HISTORY Report No. Issued Date Content 23070019HKG‐003 January 16, 2024 Original Report 23070019HKG‐003R1 January 31, 2024 Updated Model TEST REPORT Spin Master Toys Far East Ltd. Intertek Report No: 23070019HKG‐003R1 Page 3 of 19 SUMMARY OF TEST RESULT Test Items FCC Part 15 Section Results Transmitter Power Line Conducted Emissions 15.207 Not Applicable Radiated Emission Complied Radiated Emission on the Bandedge 15.249, 15.209 Complied Radiated Emission in Restricted Bands 15.205 Complied The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2021 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC Part 15 Section 15.215(c), the 20dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over expected variations in temperature and supply voltage were considered. TEST REPORT Spin Master Toys Far East Ltd. Intertek Report No: 23070019HKG‐003R1 Page 4 of 19 TABLE OF CONTENTS 1.0 GENERAL DESCRIPTION................................................................................................5 1.1 Product Description.................................................................................................5 1.2 Related Submittal(s) Grants ....................................................................................5 1.3 Test Methodology ...................................................................................................5 1.4 Test Facility..............................................................................................................5 2.0 SYSTEM TEST CONFIGURATION....................................................................................6 2.1 Justification .............................................................................................................6 2.2 EUT Exercising Software..........................................................................................6 2.3 Special Accessories..................................................................................................6 2.4 Measurement Uncertainty......................................................................................6 2.5 Support Equipment List and Description.................................................................6 3.0 EMISSION RESULTS......................................................................................................7 3.1 Field Strength Calculation .......................................................................................7 3.2 Radiated Emission Configuration Photograph.........................................................8 3.3 Radiated Emission Data...........................................................................................8 4.0 EQUIPMENT PHOTOGRAPHS......................................................................................13 5.0 PRODUCT LABELLING.................................................................................................13 6.0 TECHNICAL SPECIFICATIONS ..............................…

Text truncated - open the document above for the full version.