PWX-HHB100Headset Bluetooth HHB-100

Headset Bluetooth HHB-100 Brand Name: BenQ-Siemens Model Name: HHB-100 Headset Bluetooth ® (en) © Siemens AG 2005, C:\_Christine\Accessories\05GUW 00103 Loennerheden_Headsets HHB-100\Work\Satz\Frame left page (2) of Headset Bluetooth HHB-100en, A31008-H2801-A102-1-ZC19 2 Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE Headset Bluetooth ® HHB-100 (en) Safety precautions Important: Please read the user guide and safety precautions carefully before use! Explain the content to your children and the hazards associated with using the device. Remember to comply with legal requirements and lo- cal restrictions when using the device. For example in aeroplanes, petrol sta- tions, hospitals or while driving. The functioning of medical devices such as hearing aids or pacemakers can be impaired. Keep at least 20cm/9 inches between the device and the pace- maker. Wear the device on the ear further away from a heart pacemaker during a call. For more information consult your doctor. Caution! Young children may choke on small parts. The device must therefore be stored out of the reach of small children. Do not throw the device in- to an open fire. The device may only be opened by authorised service partners. Any changes to this device are strictly prohibited and will invalidate the operating licence. Dispose of unusable de- vices and their accesso- ries according to the legal regulations. The phone may cause in- terference in the vicinity of TV sets, radios and PCs. Use only original accesso- ries. This will avoid poten- tial damage to health or property and ensure com- pliance with all relevant regulations. Improper use will invalidate the guarantee! Permanent hearing loss may occur if you use ear- or headphones at high volume.You can adapt over time to a higher volume, which may sound nor- mal but can be damaging to your hear- ing. Set your volume to a safe level. If you experience ringing in your ears, reduce the volume or discontinue use of your system. In some countries there may be re- strictions to the use of Bluetooth ® de- vices. Please make enquiries at the authorities responsible. Headset Bluetooth ® (en) right page (3) of Headset Bluetooth HHB-100en A31008-H2801-A102-1-ZC19 © S i emens A G 2 0 0 5 , C : \ _ C h r i st i ne \ A ccessor i es \ 0 5 G U W 0 0 1 0 3 L oenner h e d en_ H ea d sets H H B - 1 0 0 \ W or k \ S atz \ F rame 3 T emp l ate: X 7 5 , V ers i on 2 . 2 ; V A R L anguage: un k nown; V A R i ssue d ate: V A R _ I ssue _ D A T E Compatibility The Headset Bluetooth ® (referred to hereafter as "headset") is suitable for telephoning with mobile phones with the Bluetooth Profile (Headset Profile or Handsfree Profile). Bluetooth ® technology The headset and the mobile phone communicate by means of Bluetooth ® , a short-range radio link. To enable this communication, the headset and mobile phone must be paired with each other. For more infor- mation please read "Establishing the first connection with the mobile phone (pairing)", page 6. The Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by BenQ Corp. is under license. Other trademarks and trade names are those of their respective owners. Please also read the notes on Bluetooth ® links in your mobile phone user guide as the controls and dis- play messages differ between phones. Headset Bluetooth ® (en) © Siemens AG 2005, C:\_Christine\Accessories\05GUW 00103 Loennerheden_Headsets HHB-100\Work\Satz\Frame left page (4) of Headset Bluetooth HHB-100en, A31008-H2801-A102-1-ZC19 4 Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE Overview of headset 1 LED signals different headset states (page 7) 2 Ear hook 3 Microphone 4 Loudspeaker with earpiece 5 a On/Off button/ Multifunction button Press briefly: Activate voice dialling or Accept a call Press and hold: End a call 6 Cover of battery compartment Headset Bluetooth ® (en) right page (5) of Headset Bluetooth HHB-100en A31008-H2801-A102-1-ZC19 © S i emens A G 2 0 0 5 , C : \ _ C h r i st i ne \ A ccessor i es \ 0 5 G U W 0 0 1 0 3 L oenner h e d en_ H ea d sets H H B - 1 0 0 \ W or k \ S atz \ F rame 5 T emp l ate: X 7 5 , V ers i on 2 . 2 ; V A R L anguage: un k nown; V A R i ssue d ate: V A R _ I ssue _ D A T E Getting started Adjusting the headset You can reverse the ear hook so that you can wear the headset on the left or right ear. 1. Pull the ear hook backwards out of its holder. 2. Turn the ear hook and careful- ly insert it on the other side: • for the left ear: • for the right ear: Wearing the headset correctly Wear the headset as shown in the diagram. The microphone- opening must always point to- wards your mouth. Bend the ear hook carefully to adjust it to your ear. Ensure that part of the project- ing end of the rubber earpiece sticks into your ear canal. Inserting the battery To operate the headset you need to use the AAA battery supplied with it. The battery is not yet inserted. To do this, open the battery compartment and insert the battery the correct way round. Corresponding markings can be found in the battery compartment. Headset Bluetooth ® (en) © Siemens AG 2005, C:\_Christine\Accessories\05GUW 00103 Loennerheden_Headsets HHB-100\Work\Satz\Frame left page (6) of Headset Bluetooth HHB-100en, A31008-H2801-A102-1-ZC19 6 Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE Switching the headset on and off •Switch on: aPress for about 2 seconds. The LED lights for 1 second continuously. A low and a high tone can be heard. If no connectable mo- bile phone can be found, please repeat the pairing. If no mo- bile phone is connect- ed with the headset, it switches off auto- matically after 1 hour. • Switch off: aPress for about 3 seconds. The LED lights continuously for 1 second and then goes out. A high and a low tone can be heard. Establishing the first connection with the mobile phone (pairing) The headset must be switched off. 1. Press the…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

4 haoyu.lee hongmin.hu jing.wang 04/17`06 04/17`06 04/17`06 50-81101SIG0 2 1/1 A4 DATE CODE SEE NOTE 1 BenQ PART NO FCC ID NOTE: 1. Year 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 Letter K L M N P R S T U V W X Month January February March April May June July August September October Nocember December Number 1 2 3 4 5 6 7 8 9 O N D

Page 3 Page 4 Page 5

FCC ID: PWX-HHB100 Report No: SA950315L05 1 RF EXPOSURE REPORT REPORT NO.: SA950315L05 MODEL NO.: HHB-100 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: BenQ Mobile GmbH & Co. OHG ADDRESS: Haidenauplatz 1, 81667 Munich , Germany ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: PWX-HHB100 Report No: SA950315L05 2 RF Exposure Measurement (Portable Device) 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: PWX-HHB100 Report No: SA950315L05 3 3. Friis Formula Friis transmission formula: Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref.: David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4 EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification This device is not fixed inside the AC Adapter that is classified as Portable Device. FCC ID: PWX-HHB100 Report No: SA950315L05 4 6 Conclusion No evaluation required if power is below this threshold: F (GHz)mW Low2.402 High2.480 24.580 Maximum measured transmitter power: Pout (dBm)Pout (mW) Conducted Power 3.46 2.218 EIRP Power 7.46 5.572 *NOTE: The antenna is Printed antenna with 4dBi gain Threshold for no SAR evaluation is 24.580mW. Transmitter power is 2.218mW. Conclusion: No SAR evaluation required since Transmitter Power is below FCC threshold.

Report No.: RF950315L051Report Format Version 2.0.4 FCC TEST REPORT REPORT NO.: RF950315L05 MODEL NO.: HHB-100 RECEIVED: Mar. 15, 2006 TESTED: Mar. 15 ~ Mar. 17, 2006 ISSUED: Mar. 22, 2006 APPLICANT: BenQ Mobile GmbH & Co. OHG ADDRESS: Haidenauplatz 1, 81667 Munich , Germany ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 51 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. NO. 2177-01 Report No.: RF950315L052Report Format Version 2.0.4 TABLE OF CONTENTS 1.CERTIFICATION.........................................................................................................4 2.SUMMARY OF TEST RESULTS................................................................................5 2.1MEASUREMENT UNCERTAINTY..............................................................................6 3.GENERAL INFORMATION.........................................................................................7 3.1 GENERAL DESCRIPTION OF EUT...........................................................................7 3.2 DESCRIPTION OF TEST MODES.............................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST........................................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..........................10 3.3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS..........................................12 3.3.4 DESCRIPTION OF SUPPORT UNITS.....................................................................12 4. TEST TYPES AND RESULTS..................................................................................13 4.1 CONDUCTED EMISSION MEASUREMENT...........................................................13 4.2 RADIATED EMISSION MEASUREMENT................................................................13 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.............................................13 4.2.2 TEST INSTRUMENTS..............................................................................................14 4.2.3 TEST PROCEDURES..............................................................................................15 4.2.4 DEVIATION FROM TEST STANDARD....................................................................15 4.2.5 TEST SETUP............................................................................................................16 4.2.6 EUT OPERATING CONDITIONS.............................................................................16 4.2.7 TEST RESULTS........................................................................................................17 4.3 NUMBER OF HOPPING FREQUENCY USED........................................................21 4.3.1 LIMIT OF HOPPING FREQUENCY USED..............................................................21 4.3.2 TEST INSTRUMENTS..............................................................................................21 4.3.3 TEST PROCEDURES..............................................................................................21 4.3.4 DEVIATION FROM TEST STANDARD....................................................................22 4.3.5 TEST SETUP............................................................................................................22 4.3.6 TEST RESULTS........................................................................................................22 4.4 DWELL TIME ON EACH CHANNEL.........................................................................24 4.4.1 LIMIT OF DWELL TIME USED.................................................................................24 4.4.2 TEST INSTRUMENTS..............................................................................................24 4.4.3 TEST PROCEDURES..............................................................................................24 4.4.4 DEVIATION FROM TEST STANDARD....................................................................24 4.4.5 TEST SETUP............................................................................................................25 4.4.6 TEST RESULTS........................................................................................................25 4.5 CHANNEL BANDWIDTH..........................................................................................29 4.5.1 LIMITS OF CHANNEL BANDWIDTH......................................................................29 4.5.2 TEST INSTRUMENTS..............................................................................................29 Report No.: RF950315L053Report Format Version 2.0.4 4.5.3 TEST PROCEDURE.................................................................................................29 4.5.4 DEVIATION FROM TEST STANDARD....................................................................30 4.5.5 TEST SETUP............................................................................................................30 4.5.6 EUT OPERATING CONDITION................................................................................30 4.5.7 TEST RESULTS........................................................................................................31 4.6 HOPPING CHANNEL SEPARATION........................................................................34 4.6.1 LIMIT OF HOPPING CHANNEL SEPARATION.......................................................34 4.6.2 TEST INSTRUMENTS.................................................…

Text truncated - open the document above for the full version.

Report No.: RF950315L0549Report Format Version 2.0.4 5. PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST