PY7-53752EGSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC

SO-XXX Quick Start Guide Be sure to read this manual before use Handling precautions These precautions are provided to prevent the product from damage and ensure that performance can be fully demonstrated. Thoroughly read these precautions to ensure correct use. Precautions common to the main unit, internal battery, charging equipment, au IC card (SIM card), peripheral devices Do not apply excessive force to the product during use. Be sure not to put the product into a tightly packed bag or place a heavy object on the product in a bag. Sitting on the product in your pocket might damage the display or internal circuit board or cause a malfunction. Keeping an external device connected to the USB Type-C connection terminal or headset connection terminal might cause damage of the connector or a malfunction. Such damage and malfunction are not covered by the warranty, even if there is no external damage. To ensure waterproof property (equivalent to IPX5 and IPX8) of the product, use with the cover of microSD memory card/au IC card (SIM card) slot tightly closed. Note that the waterproof property is not guaranteed in every usage condition. Do not allow water to get inside of the product or splash water on the specified charging equipment (sold separately) or optional accessories. Do not open or close the cover of microSD memory card/au IC card (SIM card) slot in the rain or with water droplets on the surface of the product. Doing so might cause water intrusion resulting in internal corrosion. Malfunctions determined to be caused by water intrusion are not covered by the warranty. Waterproof/dustproof performance might not be maintained if the product has an outward abnormality such as damage or deformation. In that case, contact Repair and Delivery Support Center. For the following products, do not use them in extremely hot, cold or humid places. (Use within an ambient temperature range of 5 to 35 and humidity range of 35% to 85%. However, temporary use at an ambient temperature range of 36 to 40 and humidity range of 86% to 90 % is allowed.) •Main unit •au IC card (SIM card (attached to Main unit)) United States THIS PHONE MODEL HAS BEEN CERTIFIED IN COMPLIANCE WITH THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. This mobile phone model SO-XXX has been designed to comply with applicable safety requirements for exposure to radio waves. Your wireless phone is a radio transmitter and receiver. It is designed to not exceed the limits* of exposure to radio frequency (RF) energy set by governmental authorities. These limits establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by international scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands. While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. The highest SAR value as reported to the authorities for this phone model when tested for use by the ear is 0.58 W/kg*, when worn on the body is 0.27 W/kg* and when WiFi hotspot mode is 0.34 W/kg. For body-worn operation, the phone has been tested when positioned a minimum of 10 mm from the body without any metal parts in the vicinity of the phone or when properly used with an appropriate accessory and worn on the body. For devices which include "WiFi hotspot" functionality, SAR measurements for the device operating in WiFi hotspot mode were taken using a separation distance of 10 mm. When using the device as a charger, you need to put the phone on a flat surface and 20 cm separation distance from user during the charging mode. Use of third-party accessories may result in different SAR levels than those reported. Names and functions of parts Headset jack Second microphone *1*2 Front camera Earpiece/Speaker *1*2 Proximity/Light sensor *2 : Switches the touch panel on and off to prevent from erroneous operation during a call/Auto-control for display brightness. Notification LED Display (Touch panel) Speaker *1*2 microSD memory card/ SIM card slot Mouthpiece/ Microphone *1*2 USB Type-C ® port Volume key/Zoom key Power key/Fingerprint sensor Shutter key ⑬ ⑭ ⑫ ⑦ ⑧ ① ③ ④ ⑤ ⑥ ⑨ ⑪ ② ⑩ For the following products, do not use them in extremely hot, cold or humid places. (Use within an ambient temperature range of 5 to 35 and humidity range of 35% to 85%.) •Charging equipment •Peripheral devices Do not use in places subject to lots of dust or vibration. Doing so might cause a malfunction. Clean the USB Type-C connection terminal and headset connection terminal with dry cotton swabs etc. every now and then. Soiled terminals might cause poor connection. Do not exert strong force to clean the USB Type-C connection terminal and headset connection terminal to prevent deformation. Clean the product with a soft dry cloth (e.g. wiping cloth for eyeglasses). Forceful rubbing with a dry cloth might scratch the display. The display might be stained if splash or smear is left attached to the surface. Wiping the product using alcohol, thinner, benzene, detergent, glass cleaner, etc. might erase the printing on the exterior case or cause a malfunction. Use as far away as possible from land-line phones, TVs and radios. Use of the product nearby might affect them. The product might become warm while talking, charging or during other operations, depending on the situation, but this is not abnormal. Do not place near corrosive chemicals or in places where corrosive gas is generated. Doing so might cause a malfunction. Do not use outside when …

Text truncated - open the document above for the full version.

Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Date: August 15, 2022 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA Authorization Letter for UL Verification Services Inc. FCC ID: PY7-53752E To Whom It May Concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. Yours sincerely, ________________________________ Mika Kaneko Chief Regulatory Compliance Manager Mobile Communications Business Group Sony Corporation

Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Date: August 15, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Confidentiality Request Letter FCC ID: PY7-53752E To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. - Schematic Diagram - Block Diagram - Theory of Operation - Parts List - Tune up Information Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180days from date of the Grant of Equipment Authorization. - External Photos - Internal Photos - Test Setup Photos - User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Yours sincerely, ________________________________ Mika Kaneko Chief Regulatory Compliance Manager Sony Corporation

Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Date: August 24, 2022 PY7-53752E Data Reuse Justification and Summary To Whom It May Concern: We are applying data reuse for FCC ID: PY7-53752E (variant) of the following unlicensed band based on the parent model FCC ID: PY7-58692W (Parent). Both devices share the same PCB layout, antennas and components. The unlicensed band data for the parent model remains representative for the variant model (equipment classes DSS, DTS, NII, DCD, and WPT RF Exposure) and test reports for the parent model plus test reports with the spot check data for the variant model have been submitted. The power to be listed on the F-731 and FCC grants for these bands are the values detailed in the parent reports as the spot check data shows all values within expected tolerances of the parent model. - WLAN 2.4GHz/5GHz (DTS/NII) - Bluetooth (DSS/DTS) - WPT (DCD and RF Exposure) FCC ID Bluetooth DSS Bluetooth DTS 802.11 DTS 802.11 NII DFS WPT DCD WPT RF Exposure PY7-58692W Parent 1M2207200079- 05.PY7 1M2207200079- 06.PY7 1M2207200079- 08.PY7 1M2207200079- 09.PY7 1M2207200079 -10.PY7 1M2207200079 -11.PY7 1M2207200079 -12.PY7 1M2207200079 -15.PY7 1M2207200079 -18.PY7 PY7-53752E Variant R14311587-E2 R14311587-S3 Indicates full set of test data. Values in this report to be listed on the grant for these bands. Partial test data used to confirm that the parent model data is representative for the variant model. Data for these bands is for reference only. We are also applying data reuse for FCC ID: PY7-53752E (variant) of the NFC (DXX) and WLAN and Bluetooth SAR data based on the parent model FCC ID: PY7-93060R (parent). Both devices share the same PCB layout, antennas, and components. The NFC (equipment class DXX) data for the parent model remains representative for the variant model and test reports for the parent model plus test reports with the spot check data for the variant model have been submitted. For SAR, WLAN and Bluetooth SAR data are referenced from the parent model FCC ID: PY793060R and are leveraged to cover the variant FCC ID: PY7-53752E. SAR data reuse test plan was approved via manufacturer KDB inquiry. The variant model SAR report has full tested data for the licensed bands. - WLAN 2.4GHz/5GHz/Bluetooth (SAR) - NFC (DXX) FCC ID NFC DXX SAR (WLAN/BT) PY7-93060R Parent R14311585-E3 14311585-S1 PY7-53752E Variant R14311587-E3 14311587-S1 Indicates full set of test data. Values in this report to be listed on the grant for these bands. Partial test data used to confirm that the parent model data is representative for the variant model. Data for these bands is for reference only. Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Regarding the licensed bands (equipment code PCE), the same PCB layout and the components except the licensed bands antennas are identical between PY7-17565F (parent) and PY7-53752E (variant). Therefore, the conducted test data of licensed bands from PY7-17565F can be re-used to PY7-53752E, and PY7-53752E report has full radiated test data for the licensed bands. For the detailed explanation, please refer to Theory of Operation Appendix D. Yours sincerely, ________________________________ Mika Kaneko Chief Regulatory Compliance Manager Mobile Communications Business Group Sony Corporation FCC ID WWAN PCE (conducted) PY7-17565F Parent R14311589-E1 PY7-53752E Variant R14311587-E1 Indicates full set of test data. Values in this report to be listed on the grant for these bands. Partial test data used to confirm that the parent model data is representative for the variant model. Data for these bands is for reference only.

Sony Corporation Confidential REPORT 1(3) Document number Revision PA1 Date 2022-02-22 Remarks It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. FCC ID: PY7-53752E External Photo Front Rear Confidential REPORT 2(3) Document number Revision PA1 Side view: Top/Bottom view: Confidential REPORT 3(3) Document number Revision PA1 SIM SLOT:

Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075, Japan E-Label and Label Location PY7-53752E 1 E-Label Location Users can access the FCC ID information within 3 step as the followings. Setting from Main Menu Settings -> About Phone -> Certificates 2 Access to the required information on the e-label (1) The user manual directs the user where to find the FCC ID E-Label. To view the regulatory compliance mark  Find and tap [Settings]->[About Phone]->[Certificates] Regulatory compliance mark such as FCC ID is displayed on the screen. Special codes or permissions are not required the above steps beyond the normal security protection to unlock the screen. (2) Products must not require special accessories or supplemental plug-ins. (3) The regulatory information is clearly legible without the aid of magnification. (4) The regulatory information is secure. The user can not access and modify the regulatory information. (5) The physical temporary label or the label on the packaging for purchasing and importation is attached in case of the device is sold in the United States. 3 FCC Statement FCC15.19(a) statement can be seen in the manual.

Sony Corporation Confidential REPORT 1(6) Document number Revision PA1 Date 2022-2-22 It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. FCC ID: PY7-53752E Internal Photo Without Rear panel Rear panel Without PBA and Battery Confidential REPORT 2(6) Document number Revision PA1 Scale (unit : mm) Internal Main-PWB Front with Shield cases(Front-side) Internal Main-PWB Front without Shield cases (Front-side) Internal Main-PWB Front (Rear-side) 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 Confidential REPORT 3(6) Document number Revision PA1 10 20 30 40 50 10 20 30 40 50 Confidential REPORT 4(6) Document number Revision PA1 Internal Main-PWB Rear with Shield case (Rear-side) Internal Main-PWB Rear without Shield case (Rear-side) Internal Main-PWB Rear with Shield case (Front-side) 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 10 20 30 40 50 Confidential REPORT 5(6) Document number Revision PA1 Internal Main-PWB Rear without Shield case (Front-side) Internal Sub-PWB (Front-side) Internal Sub-PBA (Rear-side) 10 20 30 40 50 10 20 30 40 50 Confidential REPORT 6(6) Document number Revision PA1 Battery:

FCC Test Results © 2022 Element Page 1 of 2 FCC ID: PY7-58692W Date: 07/26/2022 Test Procedure: KDB 680106 D01 v03r01 Test Report Serial No.: 1M2207200079-18.PY7 Table 1. E-field Measurement by Test Setup and Battery Level (Device to Device) Table 3. E-field Measurement with Worst-case Configuration (Device to Earbuds) Table 2. H-field Measurement by Test Setup and Battery Level (Device to Device) Load DUT-Load Setup Side or Edge 151515 ParallelA (Bottom)0.2470.2470.280614.00 ParallelB (Right)0.2390.2740.293614.00 ParallelC (Top)0.2570.2890.280614.00 ParallelD (Left)0.2570.2990.309614.00 ParallelE (Front)0.5370.5010.571614.00 ParallelF (Back)0.6130.6710.633614.00 PerpendicularA (Bottom)0.2820.3070.307614.00 PerpendicularB (Right)0.6960.6420.609614.00 PerpendicularC (Top)0.3130.3440.312614.00 PerpendicularD (Left)0.9750.9890.969614.00 PerpendicularE (Front)0.6290.7080.713614.00 PerpendicularF (Back)0.7620.7770.840614.00 Distance from probe (cm) Distance from probe (cm) E Measurements (V/m) Phone 50% Battery 70% Battery Limit (V/m) Distance from probe (cm) 10% Battery Load Side or Edge 15 D (Left)0.985614.00 E Measurements (V/m) Limit (V/m) Distance from probe (cm) Earbuds Load DUT-Load Setup Side or Edge 151515 ParallelA (Bottom)0.0890.1100.0771.63 ParallelB (Right)0.0720.0730.0821.63 ParallelC (Top)0.1010.1160.0871.63 ParallelD (Left)0.0720.0890.0841.63 ParallelE (Front)0.0920.0960.0771.63 ParallelF (Back)0.0830.1040.0851.63 PerpendicularA (Bottom)0.0720.0770.0541.63 PerpendicularB (Right)0.0720.0770.0511.63 PerpendicularC (Top)0.0840.0870.0701.63 PerpendicularD (Left)0.0770.0660.0581.63 PerpendicularE (Front)0.0720.0850.0631.63 PerpendicularF (Back)0.0660.0780.0581.63 Distance from probe (cm) Distance from probe (cm) Distance from probe (cm) H Measurements (A/m) 10% Battery 50% Battery 70% Battery Limit (A/m) Phone FCC Test Results © 2022 Element Page 2 of 2 Table 4. H-field Measurement with Worst-case Configuration (Device to Earbuds) A B C D E F BOTTOM EDGE RIGHT EDGE TOP EDGE LEFT EDGE FRONT (SCREEN) Back Table 5. EUT Position Description Note: 1. See Test Setup Photos for more information about the Parallel and Perpendicular DUT-Load Setups. 2. The right and left edge are determined with the EUT screen facing the user. 3. H-Field Measurements were found to be noise floor Description of Test Setup o Testing was performed with a calibrated field probe. o Measurement was performed on each side of the EUT as described per Table 5. o Testing with a second handset as the load was performed at the different battery levels indicated in Table 1 and Table 3. Testing with wireless earbuds as the load was performed using the worst-case configurations from Table 1 and Table 3. o Measurement procedure was performed per FCC Guidance. Test Equipment Table 6. Test Equipment Load Side or Edge 15 C (Top)0.0631.63 H Measurements (A/m) Limit (A/m) Distance from probe (cm) Earbuds Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number Narda EHP-200AC Electric & Magnetic Field Probe 6/9/2022 Annual 6/9/2023 170WX70211

FCC Part 1 Subpart I FCC Part 2 Subpart J TEST REPORT FOR GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC FCC ID: PY7-53752E REPORT NUMBER: R14311587-S3 ISSUE DATE: 2022-08-23 Prepared for Sony Corporation 1-7-1 Konan Minato-ku Tokyo, 108-0075, Japan Prepared by UL LLC 12 LABORATORY DR. RESEARCH TRIANGLE PARK, NC 27709 USA TEL: (919) 549-1400 REPORT NO: R14311587-S3 DATE: 2022-08-23 EUT: GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC FCC ID: PY7-53752E Page 2 of 13 UL LLC FORM NO: CCSUP4701I 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC Revision History Rev. Issue Date Revisions Revised By V1 2022-08-05 Initial Issue Niklas Haydon V2 2022-08-10 Updated top distance to 20cm in section 5.4, added data reuse section Niklas Haydon V3 2022-08-23 Removed duplicate sections, updated sections 6.2 and 6.4 Niklas Haydon REPORT NO: R14311587-S3 DATE: 2022-08-23 EUT: GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC FCC ID: PY7-53752E Page 3 of 13 UL LLC FORM NO: CCSUP4701I 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................4 2. TEST METHODOLOGY ......................................................................................................5 3. FACILITIES AND ACCREDITATION ..................................................................................5 4. DECISION RULES AND MEASUREMENT UNCERTAINTY ...............................................6 4.1. METROLOGICAL TRACEABILITY ...............................................................................6 4.2. DECISION RULES ........................................................................................................6 4.3. MEASUREMENT UNCERTAINTY ................................................................................6 5. EQUIPMENT UNDER TEST ................................................................................................7 5.1. DESCRIPTION OF EUT ...............................................................................................7 5.2. DESCRIPTION OF TEST SETUP .................................................................................7 6. REUSE OF TEST DATA ......................................................................................................9 6.1. INTRODUCTION ..........................................................................................................9 6.2. DEVICES DIFFERENCES ............................................................................................9 6.3. REFERENCE DETAIL ..................................................................................................9 6.4. SPOT CHECK VERIFICATION RESULTS SUMMARY .................................................9 7. TEST AND MEASUREMENT EQUIPMENT ......................................................................10 8. MAXIMUM PERMISSIBLE RF EXPOSURE TEST RESULTS ...........................................11 8.1. FCC LIMITS ................................................................................................................11 8.2. SUMMARY OF TEST RESULTS ................................................................................12 8.3. DETAILED TEST RESULTS .......................................................................................13 9. SETUP PHOTO .................................................................................................................13 REPORT NO: R14311587-S3 DATE: 2022-08-23 EUT: GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC FCC ID: PY7-53752E Page 4 of 13 UL LLC FORM NO: CCSUP4701I 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Sony Corporation 1-7-1 Konan Minato-ku Tokyo, 108-0075, Japan EUT DESCRIPTION: GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC SERIAL NUMBER: QV7700ETD8(Server), QV7700KKD8(Client) DATE TESTED: 2022-08-01, 2022-08-03 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Complies UL LLC tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. All samples tested were in good operating condition throughout the entire test program. Measurement Uncertainties are published for informational purposes only and were not taken into account unless noted otherwise. This document may not be altered or revised in any way unless done so by UL LLC and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL LLC will constitute fraud and shall nullify the document. Approved & Released For UL LLC By: Prepared By: Francisco de Anda Staff Engineer Niklas Haydon Operations Leader Consumer Technology Division Consumer Technology Division UL LLC UL LLC REPORT NO: R14311587-S3 DATE: 2022-08-23 EUT: GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC FCC ID: PY7-53752E Page 5 of 13 UL LLC FORM NO: CCSUP4701I 12 Laboratory Dr., RTP, NC 27709 TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC 2. TEST METHODOLOGY All testing / calculations were made in a…

Text truncated - open the document above for the full version.

TEST REPORT Report Number: R14311587-E2 Applicant : Sony Corporation 1-7-1 Konan Minato-ku Tokyo, 108-0075, Japan FCC ID : PY7-53752E EUT Description : GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPT & NFC Test Standard(s) : FCC 47 CFR PART 15 SUBPART C AND E Date Of Issue: 2022-08-23 Prepared by: UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 U.S.A. TEL: (919) 549-1400 REPORT NO: R14311587- E2 DATE: 2022-08-23 FCC ID: PY7-53752E Page 2 of 42 UL LLC 12 Laboratory Dr., RTP, NC 27709; USA TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC REVISION HISTORY Rev. Issue Date Rev isions Rev ised By V1 2022-08-02 Initial Issue Charles Moody V2 2022-08-10 Updated sections 7.3, 7.4 and added units to Corrected EIRP column Charles Moody V3 2022-08-12 Updated with DFS spot check data Charles Moody V4 2022-08-15 Updated support and measurement equipment used for DFS testing Charles Moody V5 2022-08-17 Updated note in section 7.4 Charles Moody V6 2022-08-23 Updated section 7.2 to reflect device differences and updated 7.4 spot check verification table Charles Moody REPORT NO: R14311587- E2 DATE: 2022-08-23 FCC ID: PY7-53752E Page 3 of 42 UL LLC 12 Laboratory Dr., RTP, NC 27709; USA TEL: (919) 549-1400 This report shall not be reproduced except in full, without the written approval of UL LLC TABLE OF CONTENTS REVISION HISTORY .................................................................................................................... 2 TABLE OF CONTENTS ............................................................................................................... 3 1.ATTESTATION OF TEST RESULTS .................................................................................... 4 2.TEST RESULTS SUMMARY ................................................................................................. 5 3.TEST METHODOLOGY ........................................................................................................ 5 4.FACILITIES AND ACCREDITATION .................................................................................... 5 5.DECISION RULES AND MEASUREMENT UNCERTAINTY ................................................. 6 5.1. METROLOGICAL TRACEABILITY ................................................................................. 6 5.2. DECISION RULES .......................................................................................................... 6 5.3. MEASUREMENT UNCERTAINTY .................................................................................. 6 5.4. SAMPLE CALCULATION ............................................................................................... 6 6.EQUIPMENT UNDER TEST .........................................…

Text truncated - open the document above for the full version.