PY7-PM0903GSM/WCDMA/LTE Phone + Bluetooth, DTS/UNII a/b/g/n/ac, ANT+, & NFC

Mobile Phone GSM/GPRS/EDGE 850/900/1800/1900&UMTS/HSPA Bands1/2/5&LTE Bands1/3/5/7/17/26/28/41 United States THIS PHONE MODEL HAS BEEN CERTIFIED IN COMPLIANCE WITH THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. The SOV32 Series mobile phones have been designed to comply with applicable safety requirements for exposure to radio waves. Your wireless phone is a radio transmitter and receiver. It is designed to not exceed the limits* of exposure to radio frequency (RF) energy set by governmental authorities. These limits establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by international scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands. While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. For more information on SAR, please refer to the important information chapter in the User Guide. The highest SAR value as reported to the authorities for this phone model when tested for use by the ear is 0.54 W/kg*, and when worn on the body is 0.79 W/kg*. For body-worn operation, the phone has been tested when positioned a minimum of 15 mm from the body without a n y metal parts in the vicinity of the phone or when properly used with an appropriate accessory and worn on the body. For devices which include "WiFi hotspot" functionality, SAR measurements for the device operating in WiFi hotspot mode were taken using a separation distance of 10mm. Use of third-party accessories may result in different SAR levels than those reported. ** Before a phone model is available for sale to the public in the US, it must be tested and certified by the Federal Communications Commission (FCC) that it does not exceed the limit established by the government-adopted requirement for safe exposure*. The tests are performed in positions and locations (i.e., by the ear and worn on the body) as required by the FCC for each model. The FCC has granted an Equipment Authorization for this phone model with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. While there may be differences between the SAR levels of various phones, all mobile phones granted an FCC equipment authorization meet the government requirement for safe exposure. SAR information on this phone model is on file at the FCC and can be found under the Display Grant section of http:// transition.fcc.gov/oet/ea/fccid/ after searching on FCC ID PY7- PM0903. Additional information on SAR can be found on the Mobile Manufacturers Forum EMF website at http://www.emfexplained.info/. * In the United States, the SAR limit for mobile phones used by the public is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements. ** This paragraph is only applicable to authorities and customers in the United States. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any change or modification not expressly approved by Sony may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

SOV32 Preface Thank you for buying "Xperia ™ XX" (simply called the "product" from here on). Before using the product, read "Basic Manual" (this manual) and " (Full Instruction Manual)" (Japanese) to ensure safe use and handling. Packaged items Before your start using the product, make sure that you have all the following packaged with the product. The following items are not included in the package. microSD memory card AC adapter Earphones Desktop holder microUSB cable Xperia ™ XX *1 Sony Mobile TV antenna cable 02 02SOHSA *1 Including warranty (Instruction Manual) (Japanese) Xperia ™ XX (Cautions on using Xperia ™ XX) (Japanese) (Setting Guide) (Japanese) ❖Information Purchase a specified charger (sold separately). The battery is built into the product. Illustrations used in this manual are just images for explanations. They may be different from actual ones. About Operating Instructions Basic Manual (this manual) Handles only basic operations for main features. For detailed descriptions on various functions, refer to the "Basic Manual" (Japanese) app installed on the product or " (Full Instruction Manual) (Japanese)" available on the au homepage. http://www.au.kddi.com/support/mobile/guide/manual/ Company names and product names referred to in this manual are trademarks or registered trademarks of respective companies. The TM, ® marks may be omitted in this manual. "Basic Manual" (Japanese) app This product allows you to use the "Basic Manual" (Japanese) app on the product to confirm detailed operational procedures. Certain functions can be directly activated from the app screens on which their operations are described. From the Home screen, []X[ (Customer support)]X[Basic Manual] (Japanese) When you activate for the first time, follow the onscreen instructions to download and install app. For Those Requiring an English Instruction Manual You can download the English version of the instruction manual from the au homepage (available in approximately one month after the product is released). Download URL: http://www.au.kddi.com/support/mobile/guide/manual/ Regarding notations used in this document In this manual, keys (key icons) are represented by simplified illustrations such as b, h, n, P, k. Operations of tapping menu items/icons/buttons on the screen etc. are indicated as [(name of the item etc.)]. Screen illustrations shown in this manual may look different from the actual screens. In some cases, minor details or a part of a screen may be omitted. In this manual, "microSD ™ memory card", "microSDHC ™ memory card" and "microSDXC ™ memory card" are abbreviated as "microSD memory card" or "microSD". All of the indicated amounts exclude tax unless otherwise specified. "The Company" as appears in the manual refers to the following companies: Sold by: KDDI CORPORATION, OKINAWA CELLULAR TELEPHONE COMPANY Manufactured by: Sony Mobile Communications Inc. Using au (au Disaster Countermeasure) You can use (Disaster Message Board) service, (Emergency Rapid Mail) service that distributes (Earthquake Early Warning), (Disaster and Evacuation Information) and (Tsunami Warning), (Disaster Voice Messaging Service), and (Disaster related information). 1From the Home screen, []X[ (Customer support)] X[au (au Disaster Countermeasure)] au (au Disaster Countermeasure) menu appears. An agreement screen regarding the use or an initial setting screen appears for the first time you activate this program. Follow the onscreen instructions. Using (Disaster Message Board) Disaster Message Board service enables you to register information of well-being from an area of distress via LTE NET in case of large-scale disaster such as earthquake with a seismic intensity of over 6 lower. 1au (au Disaster Countermeasure) menuX[ (Disaster Message Board)] ❖Information To register information of well-being, E-mail address (ezweb.ne.jp) is required. Set up E-mail address beforehand. Using (Emergency Rapid Mail) Emergency Rapid Mail is a service that distributes Earthquake Early Warning or Tsunami Warning delivered from the meteorological bureau or Disaster and Evacuation Information delivered from the government or local public organization to all au cell phones in specified areas simultaneously. When you receive Earthquake Early Warning, ensure your safety and take proper action according to the situation around you. When you receive a Tsunami Warning, draw away from sea coast immediately and evacuate to safe place such as upland or well-built high building. 1au (au Disaster Countermeasure) menuX[ (Emergency Rapid Mail)] ❖Information Reception of Emergency Rapid Mail is notified by a special warning tone and vibration. It is not possible to change the warning tone. *Earthquake Early Warning is notified by warning tone and voice sound ("" (It is an earthquake)), and vibration. The warning tone does not sound when receiving Emergency Rapid Mail during a call. Earthquake Early Warning may not arrive before strong tremors in areas near the epicenter. Tsunami Warning is a major tidal wave/seismic sea wave notification delivered from the meteorological bureau to the area including target coast. Disaster and Evacuation Information is a service that distributes bulletins concerning residents' safety including evacuation advisories, evacuation orders and other warnings issued by the national and local governments. The service is available only in Japan (it cannot be used overseas). No information fee or communication charge is required for receiving Emergency Rapid Mail. KDDI is not liable for damages suffered by customers resulting from the service's information, lack or delay in the information caused by transmission or system breakdowns, or other events that are outside the responsibility of KDDI. Refer to the Japan Meteorological Agency web page for details about distribution of Earthquake Early Warning. http://www.jma.go.jp/ You cannot receive Emergency Rapid Mail when your cell phone is turned off. Emergency Rapid Mail may not…

Text truncated - open the document above for the full version.

Sony Mobile Communications Company Internal REPORT 1(2) Document number Revision 14/0360-1/FCP 119 1495/4 Uen PA1 Prepared by Date 2014-08-29 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA PY7－PM0903: External Photos: Front: Rear: Sony Mobile Communications Company Internal REPORT 2(2) Document number Revision 14/0360-1/FCP 119 1495/4 Uen PA1 Prepared by Date 2014-08-29 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA Side view: Top/Bottom view:

Label and Label Location FCC ID: PY7-PM0903 Sony M obile Communications Confi denti al WORK DESCRIPTION 1(1 ) Document number Revision A Prepared by Date YOSHINORI FUSE (22714209) 2015-05-26- Conte nts responsible if oth er t han preparer Remarks This d ocument is managed i n meta Doc. Approved by FCC ID: PY7-PM0903 Front side of the EUT

Sony Mobile Communications Confidential REPORT 1(4) Document number Revision 9/0360-1/FCP 119 1495/4 Uen PA3 Prepared by Date 2014-08-27 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA PY7－PM0903: Internal Photos: Without Rear Panel Rear Panel Without Rear Panel Sony Mobile Communications Confidential REPORT 2(4) Document number Revision 9/0360-1/FCP 119 1495/4 Uen PA3 Prepared by Date 2014-08-27 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA With PWB Without PWB Internal PWB with/without Shield cases – Front (LCD)-side: Internal PWB with Shield cases (Front-side) Sony Mobile Communications Confidential REPORT 3(4) Document number Revision 9/0360-1/FCP 119 1495/4 Uen PA3 Prepared by Date 2014-08-27 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA Internal PWB without Shield cases (Front-side) Internal PWB with Shield cases (Rear-side) Internal PWB without Shield cases (Rear-side) Sony Mobile Communications Confidential REPORT 4(4) Document number Revision 9/0360-1/FCP 119 1495/4 Uen PA3 Prepared by Date 2014-08-27 Contents responsible if other than preparer Remarks Approved by SEM/CGVOHCA AKINORI YAMADA Battery:

SPORTON INTERNATIONAL INC. Page Number : 1 of 65 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A FCC RF Test Report APPLICANT : Sony Mobile Communications Inc. EQUIPMENT : GSM/WCDMA/LTE Phone + Bluetooth, DTS/UNII a/b/g/n/ac, ANT+, and NFC BRAND NAME : Sony FCC ID : PY7-PM0903 STANDARD : FCC Part 15 Subpart C §15.247 CLASSIFICATION : (DSS) Spread Spectrum Transmitter The product was received on Jul. 16, 2015 and testing was completed on Aug. 28, 2015. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. SPORTON INTERNATIONAL INC. Page Number : 2 of 65 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A TABLE OF CONTENTS REVISION HISTORY .......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ...................................................................................................................................... 5 1.3 Product Feature of Equipment Under Test ........................................................................................ 5 1.4 Modification of EUT ........................................................................................................................... 6 1.5 Testing Location ................................................................................................................................ 6 1.6 Applicable Standards ......................................................................................................................... 7 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 8 2.1 Descriptions of Test Mode ................................................................................................................. 8 2.2 Test Mode .......................................................................................................................................... 9 2.3 Connection Diagram of Test System ............................................................................................... 10 2.4 Support Unit used in test configuration and system ........................................................................ 11 2.5 EUT Operation Test Setup .............................................................................................................. 11 2.6 Measurement Results Explanation Example ................................................................................... 11 3 TEST RESULT .......................................................................................................................................... 12 3.1 Number of Channel Measurement .................................................................................................. 12 3.2 Hopping Channel Separation Measurement ................................................................................... 14 3.3 Dwell Time Measurement ................................................................................................................ 21 3.4 20dB Bandwidth Measurement ....................................................................................................... 24 3.5 Peak Output Power Measurement .................................................................................................. 31 3.6 Conducted Band Edges Measurement............................................................................................ 33 3.7 Conducted Spurious Emission Measurement ................................................................................. 40 3.8 Radiated Band Edges and Spurious Emission Measurement ........................................................ 50 3.9 AC Conducted Emission Measurement........................................................................................... 58 3.10 Antenna Requirements .................................................................................................................... 62 4 LIST OF MEASURING EQUIPMENT ........................................................................................................ 63 5 UNCERTAINTY OF EVALUATION ........................................................................................................... 65 APPENDIX A. TEST RESULT OF RADIATED EMISSION APPENDIX B. RADIATED SPURIOUS EMISSION PLOTS SPORTON INTERNATIONAL INC. Page Number : 3 of 65 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FR571615A Rev. 01 Init…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. Page Number : 1 of 3 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A Setup Photographs <Conducted Emission> Remote View Rear View SPORTON INTERNATIONAL INC. Page Number : 2 of 3 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A <Radiated Emission> Y Plane <LF> Remote View Rear View SPORTON INTERNATIONAL INC. Page Number : 3 of 3 TEL : 886-3-327-3456 Report Issued Date : Sep. 14, 2015 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : PY7-PM0903 Report Template No.: BU5-FR15CBT Version 1.0 FCC RF Test Report Report No. : FR571615A <HF> Remote View Rear View