PY7A1880028GSM 850/1900 GPRS / EDGE mobile phone with Bluetooth, FM receiver

Sony Ericsson Yizo ™ with Walkman™ User guide June 30, 2010 10:36:48 Important information Please read the Important information leaflet before you use your mobile phone. Some of the services and features described in this User guide are not supported in all countries/regions or by all networks and/or service providers in all areas. Without limitation, this applies to the GSM International Emergency Number 112. Please contact your network operator or service provider to determine availability of any specific service or feature and whether additional access or usage fees apply. Experience more. Discover how. Visit www.sonyericsson.com/support to get the most from your phone. 2 June 30, 2010 10:36:48 Getting started To insert the SIM card 2 1 1 Remove the battery cover. 3 June 30, 2010 10:36:48 2 Slide the SIM card into its holder with the gold-coloured contacts facing down. To insert or remove a memory card You may have to purchase a memory card separately. 1 Insert the memory card with the gold-coloured contacts facing down. 2 To remove the memory card, press the edge of the memory card inwards and release it immediately. 4 June 30, 2010 10:36:48 To insert the battery 1 2 1 Insert the battery with connectors facing each other. 2 Attach the battery cover. To turn on the phone 1 Press and hold down the key on the top of your phone. 2 Enter your SIM card PIN, if requested, and select Done. 3 At first startup, follow the setup instructions that appear. Your PIN is supplied by your network operator. If you want to correct a mistake made while entering your SIM card PIN, press . 5 June 30, 2010 10:36:49 To turn off the phone • Press and hold the key on the top of the phone until the phone turns off. To lock the screen • When the screen is active, briefly press the key. To unlock the screen • When the screen is locked, briefly press the key. Starting your phone for the first time The first time you start your phone, a setup wizard helps you enter essential phone settings. Follow the steps to select your language, import your SIM contacts, and set the time and date, respectively. If you prefer, you can skip some steps and access the setup wizard later from the phone settings menu. To set the phone language 1 When you start your phone for the first time, a list of languages appears. Scroll through the list and select your language. 2 Tap Done. To import contacts from a SIM card • When you start your phone for the first time with a SIM card inserted, the setup wizard prompts you to import your SIM contacts. Tap Import contacts. When you copy contacts between two phones using your SIM card, the amount and the type of information you can transfer for each contact is limited. To get more help on how to copy contacts between two phones, go to www.sonyericsson.com/support. 6 June 30, 2010 10:36:49 To set the time and date 1 When you start your phone for the first time, the setup wizard prompts you to set the time and date. Tap Time & date. 2 Find and tap Time. 3 Tap the hour and minute fields to adjust the time. 4 Tap Save. 5 Find and tap Date. 6 Tap the day, month and year fields to adjust the date. 7 Tap Save. While setting the time and date, you can also select your preferred time and date display formats. Tap Time format or Date format to select a desired format. 7 June 30, 2010 10:36:49 2 Touch and hold an item until application icons appear in four corners of the screen. 3 Drag the item into one of the corners, or into another applications pane. The items in the applications panes are the actual applications, and are not shortcuts. So if you move an item from one applications pane to another location, you are moving the actual application, and not creating a shortcut. Using the touch screen To open or highlight an item • Tap the item. To mark or unmark options • Tap the relevant checkbox, or in some cases tap the switch beside the option name. Marked checkbox Unmarked checkbox Switched on Switched off To go back to the previous screen • Tap , when this option is available. 14 June 30, 2010 10:36:50 An indicator at the top of the screen shows which of the applications panes you are in. For example, indicates you are in the middle applications pane. To open the applications panes There are two ways to open the applications panes: • From the Home screen, drag upwards. • Flick upwards from any location on the Home screen. To browse the applications panes • From the applications panes, flick right or left. To move an application 1 From the Home screen, drag upwards. 13 June 30, 2010 10:36:50 January, 20100 Applications panes Use the applications panes to get quick access to applications in your phone. You can also customise your panes. Remember that applications panes extend beyond the regular screen dimensions, so you might have to flick left or right to see everything. 12 June 30, 2010 10:36:49 To charge the phone using the power adapter • Connect the phone to a power outlet using the USB cable and the power adapter. Using the home key To go to the home screen • Press the home key. Home screen The Home screen is your gateway to the main features in your phone. You can customise it with different application icons, shortcuts, wallpaper and more. The Home screen extends beyond the regular screen display width, giving you more room to play with. Close your opened applications before going to the Home screen. Otherwise, these applications may stay running in the background and slow down your phone. 11 June 30, 2010 10:36:49 9Volume key 9 10 11 10Camera lens 11Speaker Charging the battery Your phone battery is partly charged when you buy the phone. It may take a few minutes before the battery icon appears on the screen when you connect the phone charger cable to a power source, such as a USB port or a 9 June 30, 2010 10:36:49 Getting to know your phone Phone overview 13.5 mm Audio Video Plus connector 5 8 6 1 2 3 4 7 2Power key/ screen lock 3Ear speaker 4Strap hole 5Connector for charger/USB cable 6Touch…

Text truncated - open the document above for the full version.

Sony Ericsson Yizo ™ with Walkman™ User guide June 30, 2010 10:36:48 Important information Please read the Important information leaflet before you use your mobile phone. Some of the services and features described in this User guide are not supported in all countries/regions or by all networks and/or service providers in all areas. Without limitation, this applies to the GSM International Emergency Number 112. Please contact your network operator or service provider to determine availability of any specific service or feature and whether additional access or usage fees apply. Experience more. Discover how. Visit www.sonyericsson.com/support to get the most from your phone. 2 June 30, 2010 10:36:48 Getting started To insert the SIM card 2 1 1 Remove the battery cover. 3 June 30, 2010 10:36:48 2 Slide the SIM card into its holder with the gold-coloured contacts facing down. To insert or remove a memory card You may have to purchase a memory card separately. 1 Insert the memory card with the gold-coloured contacts facing down. 2 To remove the memory card, press the edge of the memory card inwards and release it immediately. 4 June 30, 2010 10:36:48 To insert the battery 1 2 1 Insert the battery with connectors facing each other. 2 Attach the battery cover. To turn on the phone 1 Press and hold down the key on the top of your phone. 2 Enter your SIM card PIN, if requested, and select Done. 3 At first startup, follow the setup instructions that appear. Your PIN is supplied by your network operator. If you want to correct a mistake made while entering your SIM card PIN, press . 5 June 30, 2010 10:36:49 To turn off the phone • Press and hold the key on the top of the phone until the phone turns off. To lock the screen • When the screen is active, briefly press the key. To unlock the screen • When the screen is locked, briefly press the key. Starting your phone for the first time The first time you start your phone, a setup wizard helps you enter essential phone settings. Follow the steps to select your language, import your SIM contacts, and set the time and date, respectively. If you prefer, you can skip some steps and access the setup wizard later from the phone settings menu. To set the phone language 1 When you start your phone for the first time, a list of languages appears. Scroll through the list and select your language. 2 Tap Done. To import contacts from a SIM card • When you start your phone for the first time with a SIM card inserted, the setup wizard prompts you to import your SIM contacts. Tap Import contacts. When you copy contacts between two phones using your SIM card, the amount and the type of information you can transfer for each contact is limited. To get more help on how to copy contacts between two phones, go to www.sonyericsson.com/support. 6 June 30, 2010 10:36:49 To set the time and date 1 When you start your phone for the first time, the setup wizard prompts you to set the time and date. Tap Time & date. 2 Find and tap Time. 3 Tap the hour and minute fields to adjust the time. 4 Tap Save. 5 Find and tap Date. 6 Tap the day, month and year fields to adjust the date. 7 Tap Save. While setting the time and date, you can also select your preferred time and date display formats. Tap Time format or Date format to select a desired format. 7 June 30, 2010 10:36:49 2 Touch and hold an item until application icons appear in four corners of the screen. 3 Drag the item into one of the corners, or into another applications pane. The items in the applications panes are the actual applications, and are not shortcuts. So if you move an item from one applications pane to another location, you are moving the actual application, and not creating a shortcut. Using the touch screen To open or highlight an item • Tap the item. To mark or unmark options • Tap the relevant checkbox, or in some cases tap the switch beside the option name. Marked checkbox Unmarked checkbox Switched on Switched off To go back to the previous screen • Tap , when this option is available. 14 June 30, 2010 10:36:50 An indicator at the top of the screen shows which of the applications panes you are in. For example, indicates you are in the middle applications pane. To open the applications panes There are two ways to open the applications panes: • From the Home screen, drag upwards. • Flick upwards from any location on the Home screen. To browse the applications panes • From the applications panes, flick right or left. To move an application 1 From the Home screen, drag upwards. 13 June 30, 2010 10:36:50 January, 20100 Applications panes Use the applications panes to get quick access to applications in your phone. You can also customise your panes. Remember that applications panes extend beyond the regular screen dimensions, so you might have to flick left or right to see everything. 12 June 30, 2010 10:36:49 To charge the phone using the power adapter • Connect the phone to a power outlet using the USB cable and the power adapter. Using the home key To go to the home screen • Press the home key. Home screen The Home screen is your gateway to the main features in your phone. You can customise it with different application icons, shortcuts, wallpaper and more. The Home screen extends beyond the regular screen display width, giving you more room to play with. Close your opened applications before going to the Home screen. Otherwise, these applications may stay running in the background and slow down your phone. 11 June 30, 2010 10:36:49 9Volume key 9 10 11 10Camera lens 11Speaker Charging the battery Your phone battery is partly charged when you buy the phone. It may take a few minutes before the battery icon appears on the screen when you connect the phone charger cable to a power source, such as a USB port or a 9 June 30, 2010 10:36:49 Getting to know your phone Phone overview 13.5 mm Audio Video Plus connector 5 8 6 1 2 3 4 7 2Power key/ screen lock 3Ear speaker 4Strap hole 5Connector for charger/USB cable 6Touch…

Text truncated - open the document above for the full version.

Sony Ericsson Confidentiality Request 2010-07-14 CVVA10:313 SEMC/CVVALE Afrah Sadiq +46 10 80 12250 Receiver Federal Communications Commission Subject: Request for Confidentiality FCC ID: PY7A1880028 To Whom It May Concern: In accordance with §0.459 of CFR 47, Sony Ericsson Mobile Communications AS requests confidentiality for the below listed items for our mobile phone type AAB­ 1880028-BV, FCC 10: PY7A1880028: 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational/Technical Descriptions These items contain detailed system and equipment description and related information about the product which Sony Ericsson Mobile Communications AS considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Ericsson Mobile Communications AS also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, Afrah Sadiq Development Engineer - Global Type Approval Sony Ericsson Mobile Communications AS Sony Ericsson Mobile Communications AS Styrelsens sate: Lund Momsnr. VA. TNo: SE556615665801 Registered office: Lund Organisationsnr • Reg No: 556615-6658 Postadress • Mail Besoksadress • Office address Telefon • Telephone Telefax • Telefax SE-221 88 Lund Nya Vattentornet Nat 010-80 00000 Nat 010-80 02040 Sweden Lund Int +46 1080 00000 Int +46 10 80 02040

Sony Ericsson Confidentiality Request 2010-07-14 CVVA10:313 SEMC/CVVALE Afrah Sadiq +46 10 80 12250 Receiver Federal Communications Commission Subject: Request for Confidentiality FCC ID: PY7A1880028 To Whom It May Concern: In accordance with §0.459 of CFR 47, Sony Ericsson Mobile Communications AS requests confidentiality for the below listed items for our mobile phone type AAB­ 1880028-BV, FCC 10: PY7A1880028: 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational/Technical Descriptions These items contain detailed system and equipment description and related information about the product which Sony Ericsson Mobile Communications AS considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Ericsson Mobile Communications AS also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, Afrah Sadiq Development Engineer - Global Type Approval Sony Ericsson Mobile Communications AS Sony Ericsson Mobile Communications AS Styrelsens sate: Lund Momsnr. VA. TNo: SE556615665801 Registered office: Lund Organisationsnr • Reg No: 556615-6658 Postadress • Mail Besoksadress • Office address Telefon • Telephone Telefax • Telefax SE-221 88 Lund Nya Vattentornet Nat 010-80 00000 Nat 010-80 02040 Sweden Lund Int +46 1080 00000 Int +46 10 80 02040

No.2010TAR248 Page 83 of 90 ©Copyright. All rights reserved by TMC Beijing. ANNEX C: EUT photograph Mobile Phone Mobile Phone No.2010TAR248 Page 84 of 90 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone No.2010TAR248 Page 85 of 90 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone

No.2010TAR248 Page 83 of 90 ©Copyright. All rights reserved by TMC Beijing. ANNEX C: EUT photograph Mobile Phone Mobile Phone No.2010TAR248 Page 84 of 90 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone No.2010TAR248 Page 85 of 90 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone

Company Internal MARKING DRAWING 1 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 W150a, Mobile Phone Label Content, Made in 1 General information Mobile Phone label part no • 1235-7821 Bar code • Standard: according to Ericsson corporate standard 102 01–109 Uen • Print quality: C, according to ANSI X3.182-1990 as stated in Ericsson corporate standard 102 01– 1003 Uen • Quiet zone: No bar codes are allowed to be closer to a label edge than 2 mm! Text If applicable, or nothing else specified, Zebra printer Scaleable Smooth Font CG Triumvirate Bold Condensed is imposed. When needed, the text is adjusted to fit the label. Coordinates “(x/y)” under each line number specifies the bottom / left alignment for text, graphics and bar codes, x is measured vertically, and y horizontally from the upper left corner of the label (landscape format), both in mm. When needed, the alignment is adjusted to fit the label. 2 Printing information Content Format Line 1a (7,5/4,0) SIM card logo Graphics height 6,0mm, According to 1001-6195 Line 1b (7,5/31,5) WEE trashcan without bar symbol. Graphics, min. height 5mm, According to 1202-5537. Line 2a (10,5/2,0) Sony Ericsson stylized name. Graphics, height 1,5 mm. According to 1200-1925. Line 2b (10,5/19,0) Model Name “W150a” Text, height 1,2 mm. Line 2c (10,5/27,0) Software Version* “XX” Text, height 1,2 mm. *GP – Brown SW, without Sim-lock *HS – Red SW, with Sim-Lock Line 3a (13,0/2,0) Type number of the phone, “TYPE: AAB-1880028-BV”. Text, height 1,2 mm. Line 3b (13,0/19,0) HW & SW identification field, if applicable; “FFGG” Text, height 1,2 mm. According to Type-testing report under Product Model Specifying Document Line 3c (13,0/27,0) Location code of where the phone is flashed, if applicable, “XXX” Text, height 1,2 mm. Line 4a (15,0/2,0) “FCC ID: PY7A1880028” Text, height 1,2 mm. Line 4b (15,0/19,0) Production week (flash), “yy’W’ww” (yy = year, ww = week) Text, height 1,2 mm. Line 4c (15,0/27,0) Repair week, if applicable. “Ry’W’ww” (y = year, ww = week) Text, height 1,2 mm. Line 5a (17,0/2,0) “IC: 4170B-A1880028” Text, height 1,2 mm. Line 5b (17,0/19,0) Product number without revision of the Sales Item in which the phone is packed, if applicable. “SI XXXX-XXXX” Text, height 1,2 mm. Line 6 (19,0/2,0) Supplier’s identification for trace-ability of the telephone, as desired by supplier (e.g. “S/N: nnn....” for serial number). Text, height 1,2 mm. Defined by supplier. Company Internal MARKING DRAWING 2 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 Line 7 (21,0/2,0) Line 6 in bar code. As desired by supplier (e.g. only actual number). Bar code, height 2,0 mm. As desired by supplier (e.g. Code 128 symbology). Line 8 (23,5/2,0) Actual electronic serial number (IMEI) of the mobile phone, “00000000-000000-0” Text, height 1,2 mm. In the format TAC-SNR-CD. TAC and SNR derived from pos 500 in BOM. CD = check digit according to the Luhn formula (ISO/IEC 7812), GSM 02.16. Line 9 (25,5/2,0) Line 8 in bar code (only actual number, without data identifier). Bar code, height 2,0 mm. Code 128 symbology, code C subset. If uneven number of digits, code B subset shall be used for the last digit. Line 10 (28,5/2,0) Marking of origin. “Made in Xxx”; “Xxx” = actual country of production of the included telephone, in English Text, height 1,2 mm. 3 Layout The conceptual picture (for Zebra 90XiII printer, or equivalent) should not be considered as specifications, but as an additional help for setting up the label. 3.1 Conceptual picture double underlined = major changes since last revision. Company Internal MARKING DRAWING 3 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 Label placement To find the label follow these steps: 1. Remove the cover on the rear side of the product. 2. Remove the battery. 3. The label is located behind the battery. Rear side of the phone Place for battery Label placement

Company Internal MARKING DRAWING 1 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 W150a, Mobile Phone Label Content, Made in 1 General information Mobile Phone label part no • 1235-7821 Bar code • Standard: according to Ericsson corporate standard 102 01–109 Uen • Print quality: C, according to ANSI X3.182-1990 as stated in Ericsson corporate standard 102 01– 1003 Uen • Quiet zone: No bar codes are allowed to be closer to a label edge than 2 mm! Text If applicable, or nothing else specified, Zebra printer Scaleable Smooth Font CG Triumvirate Bold Condensed is imposed. When needed, the text is adjusted to fit the label. Coordinates “(x/y)” under each line number specifies the bottom / left alignment for text, graphics and bar codes, x is measured vertically, and y horizontally from the upper left corner of the label (landscape format), both in mm. When needed, the alignment is adjusted to fit the label. 2 Printing information Content Format Line 1a (7,5/4,0) SIM card logo Graphics height 6,0mm, According to 1001-6195 Line 1b (7,5/31,5) WEE trashcan without bar symbol. Graphics, min. height 5mm, According to 1202-5537. Line 2a (10,5/2,0) Sony Ericsson stylized name. Graphics, height 1,5 mm. According to 1200-1925. Line 2b (10,5/19,0) Model Name “W150a” Text, height 1,2 mm. Line 2c (10,5/27,0) Software Version* “XX” Text, height 1,2 mm. *GP – Brown SW, without Sim-lock *HS – Red SW, with Sim-Lock Line 3a (13,0/2,0) Type number of the phone, “TYPE: AAB-1880028-BV”. Text, height 1,2 mm. Line 3b (13,0/19,0) HW & SW identification field, if applicable; “FFGG” Text, height 1,2 mm. According to Type-testing report under Product Model Specifying Document Line 3c (13,0/27,0) Location code of where the phone is flashed, if applicable, “XXX” Text, height 1,2 mm. Line 4a (15,0/2,0) “FCC ID: PY7A1880028” Text, height 1,2 mm. Line 4b (15,0/19,0) Production week (flash), “yy’W’ww” (yy = year, ww = week) Text, height 1,2 mm. Line 4c (15,0/27,0) Repair week, if applicable. “Ry’W’ww” (y = year, ww = week) Text, height 1,2 mm. Line 5a (17,0/2,0) “IC: 4170B-A1880028” Text, height 1,2 mm. Line 5b (17,0/19,0) Product number without revision of the Sales Item in which the phone is packed, if applicable. “SI XXXX-XXXX” Text, height 1,2 mm. Line 6 (19,0/2,0) Supplier’s identification for trace-ability of the telephone, as desired by supplier (e.g. “S/N: nnn....” for serial number). Text, height 1,2 mm. Defined by supplier. Company Internal MARKING DRAWING 2 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 Line 7 (21,0/2,0) Line 6 in bar code. As desired by supplier (e.g. only actual number). Bar code, height 2,0 mm. As desired by supplier (e.g. Code 128 symbology). Line 8 (23,5/2,0) Actual electronic serial number (IMEI) of the mobile phone, “00000000-000000-0” Text, height 1,2 mm. In the format TAC-SNR-CD. TAC and SNR derived from pos 500 in BOM. CD = check digit according to the Luhn formula (ISO/IEC 7812), GSM 02.16. Line 9 (25,5/2,0) Line 8 in bar code (only actual number, without data identifier). Bar code, height 2,0 mm. Code 128 symbology, code C subset. If uneven number of digits, code B subset shall be used for the last digit. Line 10 (28,5/2,0) Marking of origin. “Made in Xxx”; “Xxx” = actual country of production of the included telephone, in English Text, height 1,2 mm. 3 Layout The conceptual picture (for Zebra 90XiII printer, or equivalent) should not be considered as specifications, but as an additional help for setting up the label. 3.1 Conceptual picture double underlined = major changes since last revision. Company Internal MARKING DRAWING 3 (3) Prepared (also subject responsible if other) No. Flora Kang (28848956) 1240-8448 Approved Checked Date Rev Reference Flora Kang (28848956) 2010-05-20 1 2 Label placement To find the label follow these steps: 1. Remove the cover on the rear side of the product. 2. Remove the battery. 3. The label is located behind the battery. Rear side of the phone Place for battery Label placement

No.2010TAR247 Page 11 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone No.2010TAR247 Page 12 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile phone Disassembly Mobile phone Disassembly No.2010TAR247 Page 13 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile phone Disassembly Mobile phone Disassembly No.2010TAR247 Page 14 of 21 ©Copyright. All rights reserved by TMC Beijing. Battery Battery No.2010TAR247 Page 15 of 21 ©Copyright. All rights reserved by TMC Beijing. Data Cable

No.2010TAR247 Page 11 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile Phone Mobile Phone No.2010TAR247 Page 12 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile phone Disassembly Mobile phone Disassembly No.2010TAR247 Page 13 of 21 ©Copyright. All rights reserved by TMC Beijing. Mobile phone Disassembly Mobile phone Disassembly No.2010TAR247 Page 14 of 21 ©Copyright. All rights reserved by TMC Beijing. Battery Battery No.2010TAR247 Page 15 of 21 ©Copyright. All rights reserved by TMC Beijing. Data Cable

No.2010SAR00053 Page 1 of 58 ©Copyright. All rights reserved by TMC Beijing. SAR TEST REPORT for FCC No. 2010SAR00053 For Sony Ericsson Mobile Communications(China) Co., Ltd. GSM 850/1900 dual bands mobile phone AAB-1880028-BV With Hardware Version: A Software Version: R2AC001 SEMC ID: AAB-1880028-BV Industry Canada ID: 4170B-A1880028 FCCID: PY7A1880028 Issued Date: 2010-7-1 No. DGA-PL-114/01-02 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of TMC Beijing. Test Laboratory: TMC Beijing, Telecommunication Metrology Center of MIIT No. 52, Huayuan Bei Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2079, Fax:+86(0)10-62304793 Email:[email protected]. www.emcite.com No. 2010SAR00053 Page 2 of 58 TABLE OF CONTENT 1 TEST LABORATORY..................................................................................................................3 1.1 TESTING LOCATION........................................................................................................................................ 3 1.2 TESTING ENVIRONMENT................................................................................................................................. 3 1.3 PROJECT DATA............................................................................................................................................... 3 1.4 SIGNATURE..................................................................................................................................................... 3 2 GENERAL INFORMATION .........................................................................................................4 2.1 STATEMENT OF COMPLIANCE......................................................................................................................... 4 2.2 APPLICANT INFORMATION.............................................................................................................................. 4 2.3 MANUFACTURER INFORMATION..................................................................................................................... 4 3 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ................................5 3.1 ABOUT EUT ................................................................................................................................................... 5 3.2 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST.......................................................................... 5 3.3 INTERNAL IDENTIFICATION OF AE USED DURING THE TEST............................................................................. 5 3.4 ANTENNA DESCRIPTION.................................................................................................................................. 5 4 CHARACTERISTICS OF THE TEST ..........................................................................................6 4.1 APPLICABLE LIMIT REGULATIONS.................................................................................................................. 6 4.2 APPLICABLE MEASUREMENT STANDARDS...................................................................................................... 6 5 OPERATIONAL CONDITIONS DURING TEST ..........................................................................6 5.1 SCHEMATIC TEST CONFIGURATION................................................................................................................. 6 5.2 SAR MEASUREMENT SET-UP.......................................................................................................................... 6 5.3 DASY4 E-FIELD PROBE SYSTEM..................................................................................................................... 7 5.4 E-FIELD PROBE CALIBRATION........................................................................................................................ 8 5.5 OTHER TEST EQUIPMENT...............................................................................................................................9 5.6 EQUIVALENT TISSUES..................................................................................................................................... 9 5.7 SYSTEM SPECIFICATIONS.............................................................................................................................. 10 6 CONDUCTED…

Text truncated - open the document above for the full version.