PY7A3022081Licensed transmitter

Sony Ericsson S ~Mlmms PMt'll6f%~~4@T390&!fPhone Confidentiality Request Datum . Date Beteckning - Reference 2007-07-09 BGL107:282 Ert datum Your date Er beteckning - Your reference Receiver Federal Communications Commission Subject: Request for Confidentiality FCC ID: PY7A3022081 To Whom It May Concern: In accordance with s0.459 of CFR 47, Sony Ericsson Mobile Communications AB requests confidentiality for the below listed items for our mobile phone type AAD- 3022081-BV, FCC ID: PY7A3022081: 1. Block Diagram 2. Schematic Diagram 3. Part List 4. OperationallTechnicaI Descriptions These items contain detailed system and equipment description and related information about the product which Sony Ericsson Mobile Communications AB considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Ericsson Mobile Communications AB also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, Kent Lorentzon Development Engineer - Global Type Approvals Sony Ericsson Mobile Communications AB Sony Ericsson Mobile Communications AB Styrelsens sate: Lund Momsnr YA.TNo: SE556615665801 Registered office: Lund Organisationsnr Reg No: 55661 5-6658 Postadress Mail Besoksadress Office address Telefon Telephone Telefax . Telefax SE-221 88 Lund Nya Vattentornet Nat 046-1 9 40 00 Nat 046-1 9 41 00 Sweden Lund Int +46 46 19 40 00 Int +46 46 19 41 00

CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 17 of 26 8 Photographs of t he E UT Photo documentation Photo 4: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 18 of 26 Photo 5: Photo 6: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 19 of 26 Photo 7: Photo 8: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 20 of 26 Photo 9: Photo 10:

Company Internal MARKING DRAWING 1 (3) Prepared (also subject responsible if other) No. SEM/BGLDB, Monica Towman 1202-5922 Uen Approved Checked Date Rev Reference SEM/BGLDB (Monica Towman) 2007-07-07 1 3 Approved according to 000 21–LXE 107 42/1 Mobile Phone label content, Made in... 1 General information Core Unit label part no 1200-0787 Bar code • Standard: according to Ericsson corporate standard 102 01–109 Uen • Print quality: C, according to ANSI X3.182-1990 as stated in Ericsson corporate standard 102 01– 1003 Uen • Quiet zone: No bar codes are allowed to be closer to a label edge than 2 mm! Text If applicable, or nothing else specified, Zebra printer Scaleable Smooth Font CG Triumvirate Bold Condensed is imposed. When needed, the text is adjusted to fit the label. Coordinates “(x/y)” under each line number specifies the bottom / left alignment for text, graphics and bar codes, x is measured vertically, and y horizontally from the upper left corner of the label (landscape format), both in mm. When needed, the alignment is adjusted to fit the label. MLCI= Main Label Content Information-document. 2 Printing information Content Format Line 1a (7,5/1,0) Sony Ericsson stylized name. Graphics, height 1,5 mm. According to 1200-1925. Line 1b (7,5/14) Model Name “T650i” Text, height 1,2 mm. Line 2a (9,4/1,0) “TYPE: AAD-3022081-BV” Text, height 1,2 mm. Line 2b (9,4/15,6) HW & SW identification field, if applicable; “FG” Text, height 1,2 mm. According to Type-testing report in BOM pos 1C. Line 2c (9,4/18,1) Location code of where the phone is flashed, if applicable, “XXX” Text, height 1,2 mm. Line 3a (11,1/1,0) “FCC ID: PY7A3022081” Text, height 1,2 mm. Line 3b (11,1/15,1) Production week (flash), “yy’W’ww” (yy = year, ww = week) Text, height 1,2 mm. Line 3c (11.1/22) CE approval symbol Graphics, height 5 mm. According to 1202-5482. Line 3d (11.1/29) The notified body number “0682” Text, height 1,2 mm. Line 4a (12,7/1,0) “IC: 4170B-A3022081” Text, height 1,2 mm. Line 4b (12,7/14,3) Product number without revision of the Sales Item in which the phone is packed, if applicable. “SI XXXX-XXXX” Text, height 1,2 mm. Line 4c (12,7/25,0) Repair week, if applicable. “Ry’W’ww” (y = year, ww = week) Text, height 1,2 mm. Company Internal MARKING DRAWING 2 (3) Prepared (also subject responsible if other) No. SEM/BGLDB, Monica Towman 1202-5922 Uen Approved Checked Date Rev Reference SEM/BGLDB (Monica Towman) 2007-07-07 1 3 Content Format Line 5 (15,1/2.6) Line 6a in bar code. As desired by supplier (e.g. only actual number). Bar code, height 2,0 mm. As desired by supplier (e.g. Code 128 symbology). Line 6a (16,9/1,0) Supplier’s identification for trace-ability of the telephone, as desired by supplier (e.g. “S/N: nnn....” for serial number). Text, height 1,2 mm. Defined by supplier. Line 6b (16,9/16,1) Actual electronic serial number (IMEI) of the Mobile Phone, “00000000-000000-0” Text, height 1,2 mm. In the format TAC-SNR-CD. TAC and SNR derived from pos 500 in BOM. CD = check digit according to the Luhn formula (ISO/IEC 7812), GSM 02.16. Line 7 (19,1/2,6) Line 6b in bar code (only actual number, without data identifier). Bar code, height 2,0 mm. Code 128 symbology, code C subset. If uneven number of digits, code B subset shall be used for the last digit. Line 8 (21,0/1,0) Marking of origin: “Xxx”= actual country of production of the included telephone, in English. Text, height 1,2 mm. 3 Layout The conceptual picture (for Zebra 90XiII printer, or equivalent) should not be considered as specifications, but as an additional help for setting up the label. 3.1 Conceptual picture double underlined = major changes since last revision. Company Internal MARKING DRAWING 3 (3) Prepared (also subject responsible if other) No. SEM/BGLDB, Monica Towman 1202-5922 Uen Approved Checked Date Rev Reference SEM/BGLDB (Monica Towman) 2007-07-07 1 3 3.1 Label placement To find the label follow these steps: 1. Remove the cover on the rear side of the product. 2. Remove the battery. 3. The label is located below the battery. Rear side of the phone Place for battery Label placement

CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 21 of 26 Photo 11: Photo 12: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 22 of 26 Photo 13: Photo 14: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 23 of 26 Photo 15: Photo 16: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 24 of 26 Photo 17: Photo 18: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 25 of 26 Photo 19: Photo 20: CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 26 of 26 Photo 21:

Company Internal REPORT 1 (11) Prepared (also subject responsible if other) No. LD/SEMC/BGLIM Magnus Söderman BGLI07:264 Approved Checked Date Rev Reference LD/SEMC/BGLIR/C Mats Hansson 070723 070703 A File Report issued by Accredited SAR Laboratory for PY7A3022081 (T650i) Date of test: 20 th June - 4 th July, 2007 Laboratory: Sony Ericsson SAR Test Laboratory Sonyericsson Mobile Communications AB Nya Vattentornet SE-221 82 LUND, Sweden Testing Engineer: Magnus Söderman [email protected] +46-46-2127229 Testing Approval: Mats Hansson [email protected] +46-46-2126180 Statement of Compliance Sony Ericsson Mobile Communications AB declares under its sole responsibility that the product Sony Ericsson Type AAD-3022081-BV; FCC ID: PY7A3022081; IC: 4170B-A3022081 to which this declaration relates, is in conformity with the appropriate RF exposure standards recommendations and guidelines. It also declares that the product was tested in accordance with the appropriate measurement standards, guidelines and recommended practices. Any deviations from these standards, guidelines and recommended practices are noted below: (None) This laboratory is accredited to ISO/IEC 17025 (SWEDAC accreditation no. 1847). Laboratories are accredited by the Swedish Board for Accreditation and Conformity Assessment (SWEDAC) under the terms of Swedish legislation. The accredited laboratory activities meet the requirements in SS-EN ISO/IEC 17025 (2005). This report may not be reproduced other than in full, except with the prior written approval of the issuing laboratory. The results and statements contained herein relate only to the items tested. The names of individuals involved may be mentioned only in connection with the statements or results from this report. Sony Ericsson encourages all feedback, both positive and negative, on this report. © Sony Ericsson Mobile Communication AB, 2007 Company Internal REPORT 2 (11) Prepared (also subject responsible if other) No. LD/SEMC/BGLIM Magnus Söderman BGLI07:264 Approved Checked Date Rev Reference LD/SEMC/BGLIR/C Mats Hansson 070723 070703 A File 1 Table of contents 1 TABLE OF CONTENTS .................................................................................................................................................. 2 2 INTRODUCTION ............................................................................................................................................................. 3 3 DEVICE UNDER TEST ................................................................................................................................................... 3 3.1 ANTENNA DESCRIPTION.............................................................................................................................................. 3 3.2 DEVICE DESCRIPTION................................................................................................................................................... 3 4 TEST EQUIPMENT.......................................................................................................................................................... 4 4.1 DOSIMETRIC SYSTEM................................................................................................................................................... 4 4.2 ADDITIONAL EQUIPMENT............................................................................................................................................. 4 5 ELECTRICAL PARAMETERS ON THE TISSUE SIMULATING LIQUID ............................................................ 5 6 SYSTEM ACCURACY VERIFICATION ...................................................................................................................... 5 7 SAR MEASUREMENT UNCERTAINTY ...................................................................................................................... 6 8 TEST RESULTS ................................................................................................................................................................ 7 9 REFERENCES .................................................................................................................................................................. 8 10 APPENDIX .................................................................................................................................................................... 9 10.1 PHOTOGRAPHS OF THE DEVICE UNDER TEST................................................................................................................. 9 10.2 DEVICE POSITION AT SAM TWIN PHANTOM.............................................................................................................. 10 10.3 ATTACHMENTS.......................................................................................................................................................... 11 Company Internal REPORT 3 (11) Prepared (also subject responsible if other) No. LD/SEMC/BGLIM Magnus Söderman BGLI07:264 Approved Checked Date Rev Reference LD/SEMC/BGLIR/C Mats Hansson 070723 070703 A File 2 Introduction In this test report, compliance of the Sony Ericsson PY7A3022081 (T650i) portable telephone with RF safety guidelines is demonstrated. The applicable RF safety guidelines and the SAR measurement specifications used for the test are described in the SAR Measurement Specifications of Wireless Handsets [1]. 3 Device Under Test 3.1 Antenna Description Type Internal antenna Location Inside at bottom of backside Max length 15 mm Dimensions Max width 40 mm Configuration Meander 3.2 Device description Device model PY7A3022081 Market name T650i Serial numbers CB510N9AY8 (#8053) Mode GSM1900 Crest factor 8.3 Multiple Access Scheme TDMA Ch.512 Ch.699 Ch.885 Maximum Output Power Setting [dBm] 29.4 29.4 29.4 Factory Tolerance in Power Setting ±0.5dB Maximum Peak Output Power 29.9 29.9 29.9 Mode GSM1900-GPRS2TX Crest factor 4.15…

Text truncated - open the document above for the full version.

CETECOM ICT Services GmbH Untertürkheimer Straße 6-10 . D-66117 Saarbrücken Phone: +49 (0) 681-598-0 Fax:-9075 RSC-Laboratory 2007-06-28 Page 1 of 36 Accredited testing-laboratory DAR registration number: DAT-P-176/94-D1 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Recognized by the Federal Communications Commission Anechoic chamber registration no.: 90462 (FCC) Anechoic chamber registration no.: 3463A-1 (IC) Certification ID: DE 0001 Accreditation ID: DE 0002 Accredited Bluetooth ® Test Facility (BQTF) The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cetecom ICT is under license Test report no. : 2-4576-20-02/07 Type identification : AAD-3022081-BV Applicant : Sony Ericsson Mobile Communications AB FCC ID : PY7A3022081 IC Certification No : 4170B-A3022081 Test standards : 47 CFR Part 24 RSS - 133 Issue 3 CETECOM ICT Services GmbH Test report no.: 2-4576-20-02/07 2007-06-28 Page 2 of 36 Table of contents 1 G e n e r a l i n f o r m a t i o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 3 1.1 Notes ...................................................................................................................................................................3 1.2 Testing laboratory ...............................................................................................................................................4 1.3 Details of applicant .............................................................................................................................................4 1.4 Application details ..............................................................................................................................................4 2 T e s t s t a n d a r d / s : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 5 3 T e c h n i c a l t e s t s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . 6 3.1 Details of manufacturer .......................................................................................................................................6 3.1.1 Test item......................................................................................................................................................6 3.2 Test Setup............................................................................................................................................................7 4 S t a t e m e n t o f C o m p l i a n c e . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . 8 4.1 Summary of Measurement Results......................................................................................................................8 4.1.1 PCS 1900.....................................................................................................................................................8 5 M e a s u r e m e n t s a n d r e s u l t s . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . 9 5.1 PART PCS 1900 .................................................................................................................................................9 5.1.1 RF Power Output.........................................................................................................................................9 5.1.2 Frequency Stability ...................................................................................................................................13 5.1.3 Radiated Emissions ...................................................................................................................................16 5.1.4 Receiver Radiated Emissions ....................................................................................................................23 5.1.5 Conducted Spurious Emissions .................................................................................................................26 5.1.6 Block Edge Compliance............................................................................................................................29 5.1.7 Occupied Bandwidth .................................................................................................................................31 6 T e s t e q u i p m e n t a n d a n c i l l a r i e s u s e d f o r t e s t s . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 3 5 CETECOM ICT Services GmbH Test report no.: 2-4576-20-02/07 2007-06-28 Page 3 of 36 1 General infor mat ion 1 . 1 N o t e s The test results of this test report relate exclusively to the test item specified in 1.5. The CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalisations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the CETECOM ICT Services GmbH. Test laboratory manager: 2007-06-28 Jakob Reschke Date Name Signature Technical responsibility for area of testing: 2007-06-28 Michael Berg Date Name Signature CETECOM ICT Services GmbH Test report no.: 2-4576-20-0…

Text truncated - open the document above for the full version.

CETECOM ICT Services GmbH Untertürkheimer Straße 6-10 . D-66117 Saarbrücken Phone: +49 (0) 681-598-0 Fax:-9075 RSC-Laboratory 2007-06-28 Page 1 of 26 Accredited testing-laboratory DAR registration number: DAT-P-176/94-D1 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Recognized by the Federal Communications Commission Anechoic chamber registration no.: 90462 (FCC) Anechoic chamber registration no.: 3463A-1 (IC) Certification ID: DE 0001 Accreditation ID: DE 0002 Accredited Bluetooth ® Test Facility (BQTF) The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cetecom ICT is under license Annex to Test report no. : 2-4576-20-02/07 Type identification : AAD-3022081-BV Applicant : Sony Ericsson Mobile Communications AB FCC ID : PY7A3022081 IC Certification No : 4170B-A3022081 Test standards : 47 CFR Part 24 RSS - 133 Issue 3 CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 2 of 26 Table of contents 1 G e n e r a l i n f o r m a t i o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 3 1.1 Notes ...................................................................................................................................................................3 1.2 Testing laboratory ...............................................................................................................................................4 1.3 Details of applicant .............................................................................................................................................4 1.4 Application details ..............................................................................................................................................4 2 T e c h n i c a l t e s t s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . 5 2.1 Details of manufacturer .......................................................................................................................................5 2.2 Test item(s) and test configuration ......................................................................................................................5 3 S u m m a r y o f M e a s u r e m e n t R e s u l t s a n d l i s t o f a l l p e r fo r m e d t e s t c a s e s . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 M e a s u r e m e n t s a n d r e s u l t s . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . 7 5 A n n e x A : F C C P a r t 1 5 S u b p a r t B . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 8 5.1 Conducted Limits ................................................................................................................................................8 5.2 Receiver spurious emission radiated (Idle mode) .............................................................................................10 6 T e s t e q u i p m e n t a n d a n c i l l a r i e s u s e d f o r t e s t s . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 1 3 7 P h o t o g r a p h s o f t h e T e s t S e t - u p . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 1 5 8 P h o t o g r a p h s o f t h e E U T . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . 1 7 CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 3 of 26 1 General infor mat ion 1 . 1 N o t e s The test results of this test report relate exclusively to the test item specified in 1.5. The CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalisations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the CETECOM ICT Services GmbH. Test laboratory manager: 2007-06-28 Jakob Reschke Date Name Signature Technical responsibility for area of testing: 2007-06-28 Michael Berg Date Name Signature CETECOM ICT Services GmbH Annex to Test report no.: 2-4576-20-02/07 2007-06-28 Page 4 of 26 1 . 2 T e s t i n g l a b o r a t o r y CETECOM ICT Services GmbH Untertürkheimer Straße 6 - 10 66117 Saarbrücken Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 e-mail: [email protected] Internet: http://www.cetecom-ict.de State of accreditation: Accredited by: The test laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 DAR registration number: DAT-P-176/94-D1 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Testing location, if different from CETECOM ICT Services GmbH: Name : Street : Town : Country : Phone : Fax : 1 . 3 D e t a i l s o f a p p l i c a n t Name: Sony Ericsson Mobile Communications AB Street: Nya Vattentornet Town: 22188 Lund Country: Sweden Telephone: +46-46-19-3000 Fax: +46-46-19-3295 Contact: Peter Lindeborg E-mail: [email protected] Telephone: +46-46-212-6180 1 . 4 A p p l i c a t i o n d e t a i l s Date of receipt of order: 2007-06-18 Date of receipt of test item: 2007-06-19 Date of start test: 2007-06-1…

Text truncated - open the document above for the full version.