PY7BC051021Quadband GPRS Module

GR64 GSM/GPRS Modem Integrators Manual LZT 123 1834 2 The information contained in this document is the proprietary information of Sony Ericsson Mobile Communications International. The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Sony Ericsson Mobile Communications International, is strictly prohibited. Further, no portion of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, without the prior written consent of Sony Ericsson Mobile Communications International, the copyright holder. First Edition (March 2006) Second Edition (May 2006) Sony Ericsson Mobile Communications International publishes this manual without making any warranty as to the content contained herein. Further Sony Ericsson Mobile Communications International reserves the right to make modifications, additions and deletions to this manual due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this manual. All rights reserved. © Sony Ericsson Mobile Communications International, 2006 Publication number: LZT 123 1834 Printed in US LZT 123 1834 3 Revision History Edition Change Information First First Edition Second Updated FCC marking requirements Signal connectivity table updated Modified description of UART1 signal behavior LZT 123 1834 4 Contents Overview....................................................................................................... 9 1 Introduction.......................................................................................... 10 1.1 TARGET USERS......................................................................................................... 10 1.2 PREREQUISITES......................................................................................................... 10 1.3 MANUAL STRUCTURE ............................................................................................... 10 1.4 NOTATION............................................................................................................... 11 1.5 ACKNOWLEDGEMENTS ............................................................................................. 12 2 GR64 Wireless Modem .......................................................................... 13 2.1 ABOUT THE GR64 .................................................................................................... 13 2.2 WIRELESS MODEMS IN A COMMUNICATION SYSTEM .................................................. 14 2.3 FEATURES ................................................................................................................ 16 2.3.1 TYPES OF MOBILE STATION ............................................................................... 16 2.3.2 SHORT MESSAGE SERVICE.................................................................................. 16 2.3.3 VOICE CALLS..................................................................................................... 17 2.3.4 DATA................................................................................................................ 17 2.3.5 GPRS MULTI-SLOT SUPPORT.............................................................................. 18 2.3.6 SIM CARD ......................................................................................................... 18 2.3.7 POWER CONSUMPTION...................................................................................... 18 2.3.8 OPERATING ENVIRONMENT ............................................................................... 19 2.3.9 OTHER FEATURES.............................................................................................. 19 2.4 SERVICE AND SUPPORT ............................................................................................ 20 2.4.1 WEB PAGES ....................................................................................................... 20 2.4.2 AT COMMANDS MANUAL .................................................................................. 20 2.4.3 M2MPOWER APPLICATION GUIDE....................................................................... 20 2.4.4 DEVELOPER’S KIT .............................................................................................. 20 2.5 PRECAUTIONS .......................................................................................................... 21 2.6 GUIDELINES FOR SAFE AND EFFICIENT USE................................................................ 21 2.6.1 GENERAL USAGE ............................................................................................... 21 LZT 123 1834 5 2.6.2 RADIO FREQUENCY (RF) EXPOSURE AND SAR ..................................................... 22 2.6.3 PERSONAL MEDICAL DEVICES ............................................................................ 22 2.6.4 DISPOSAL OF OLD ELECTRONIC EQUIPMENT ...................................................... 23 2.7 PRODUCT MARKING ................................................................................................. 23 3 Abbreviations ....................................................................................... 24 Integrating the Wireless Modem.................................................................. 26 4 Mechanical Description ......................................................................... 27 4.1 INTERFACE DESCRIPTION ......................................................................................... 27 4.2 PHYSICAL DIMENSIONS ............................................................................................ 29 5 System Connector Interface ............................................…

Text truncated - open the document above for the full version.

Date May 10, 2006 DECLARATION TO WHOM IT MAY CONCERN We, Sony Ericsson Mobile Communications AB, hereby declare that the following product: FCC ID Title / Model PY7BC051021 GR64 Type BAC-1051021-BV meets the FCC Part 15 Transmitter requirements for a modular transmitter as listed below: a) RF shielding, b) buffered modulation / data inputs, c) power supply regulation, d) antenna requirements, e) stand-alone configuration for testing, f) FCCID marking (refer to instructions in Integrators Manual), g) operating requirements (refer to instructions in Integrators Manual). If you have any questions, please contact me at the address shown below. Yours sincerely, Michael Bower Sony Ericsson Mobile Communications AB 1 Lakeside Road, Aerospace Centre Farnborough, Hampshire, GU14 6XP, UK Phone: +441252551631 E-mail: [email protected]

Date April 20, 2006 CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, Sony Ericsson Mobile Communications AB requests confidentiality for the following products: FCC ID Title / Model PY7BC051021 GR64 Type BAC-1051021-BV For the product stated above, we request that the following information be held confidential: 1. Circuit diagrams and PCBs submitted as Equipment Authorization Electronic Filing attachment: “schematics”. 2. Block diagram submitted as Equipment Authorization Electronic Filing attachment: “blockdiagram”. 3. Operational description submitted as Equipment Authorization Electronic Filing attachment: “operational description”. 4. Part List and Tune Up Info submitted as Equipment Authorization Electronic Filing attachment: “Part List / Tune Up Info”. The above exhibits contain Sony Ericsson Mobile Communications AB trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our cellular modules. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please contact me at the address shown below. Sincerely, Michael Bower Sony Ericsson Mobile Communications AB 1 Lakeside Road, Aerospace Centre Farnborough, Hampshire, GU14 6XP, UK Phone: +441252551631 E-mail: [email protected]

Confidential MARKING DRAWING 1 (5) Prepared (also subject responsible if other) No. GBFA/SEM/BMD/TP Pam Wood 151 86 - KRD 104 1031 Uen Approved Checked Date Rev Reference GBFA/SEM/BMD/U (Michael Bower) 2006-02-16 A 151 86-KRD 104 1031 Rev A.doc Marking Drawing Type 1051021-BV series Label The label used for marking is defined in the Manufacturing Specification on the SVF 930 2460. Placing The label shall be placed on the back of the module according to the Assembly Drawing (151 88) for the KRD. Print layout Confidential 2 (5) Prepared (also subject responsible if other) No. GBFA/SEM/BMD/TP Pam Wood 151 86 - KRD 104 1031 Uen Approved Checked Date Rev Reference GBFA/SEM/BMD/U (Michael Bower) 2006-02-16 A 151 86-KRD 104 1031 Rev Definitions Line 1 Sony Ericsson trademark 2 Industry Canada marking 3 FCC approval marking 4 IMEI number as bar code 5 IMEI number as characters 6 Type number 7a KRD number, R-state 7b Product Name “GR64” 8a Marking of origin 8b Production Week as bar code 9 Approval Mark Sony Ericsson trademark Sony Ericsson and the Sony Ericsson trademark shall be according to the corporate standard 190 89-EN/LZT 108 5347. Height min. 2 mm. Industry Canada marking Industry Canada approval marking: consists of text: IC: 4170B-BC051021 Approval marks FCC approval marking: consists of the text: FCC ID: PY7BC051021 Within a frame with height > 1.5 mm. IMEI number as bar code See below for definition of IMEI-number. The bar code shall only contain the digits of the IMEI number (no -). Product Name Text “GR64”. Type Size 1.5mm (min). IMEI number as characters The IMEI number has format: TAC - SNR - CD TAC = First eight digits of the Type Approval code after assignment from the Notified Body. Refer to table 1 below. SNR = A serial number from 000 000 to 999 999 according to factory Confidential 3 (5) Prepared (also subject responsible if other) No. GBFA/SEM/BMD/TP Pam Wood 151 86 - KRD 104 1031 Uen Approved Checked Date Rev Reference GBFA/SEM/BMD/U (Michael Bower) 2006-02-16 A 151 86-KRD 104 1031 Rev allocation. Refer to Table 1 below. CD = A check digit, from 0-9, calculated according to the Luhn formula (ISO/IEC 7812), GSM 02.16. Type number The type number is BAC-1051021-xx and shall be printed “Type BAC-1051021-xx”. Refer to table 1 below. KRD number The KRD number for the product (including any variant number e.g. “/12”). Refer to table 1 below. R-state The R-state for the KRD according to the 1095 for the KRD. Manufacturing country Marking of origin shall be printed Production week The production week shall be given as yyWww (yy = year, ww = week) Table 1 KRD variant Type Number IMEI TAC code IMEI SNR Allocated factory / 10 BAC-1051021-AA xxxxxxxx 000000 to 099999 xxxxxxxx / 20 BAC-1051021-BA xxxxxxxx 000000 to 099999 xxxxxxxx / 30 BAC-1051021-AB xxxxxxxx 000000 to 099999 xxxxxxxx / 40 BAC-1051021-BB xxxxxxxx 000000 to 099999 xxxxxxxx Confidential 4 (5) Prepared (also subject responsible if other) No. GBFA/SEM/BMD/TP Pam Wood 151 86 - KRD 104 1031 Uen Approved Checked Date Rev Reference GBFA/SEM/BMD/U (Michael Bower) 2006-02-16 A 151 86-KRD 104 1031 Rev Print regulations The printing shall be legible and permanent. Other texts, which are not defined above, have the following characteristics: Typeface: ZPL II standard font D Type size: min 1.1 mm Line spacing: min 1.5 mm Trademark: min 1.5 mm Approval marks: min 5.0 mm Confidential 5 (5) Prepared (also subject responsible if other) No. GBFA/SEM/BMD/TP Pam Wood 151 86 - KRD 104 1031 Uen Approved Checked Date Rev Reference GBFA/SEM/BMD/U (Michael Bower) 2006-02-16 A 151 86-KRD 104 1031 Rev Print layout for prototypes Line 2 is replaced with alternative text shown below. Type size min. 5 mm. PROTOTYPE EP1 PROTOTYPE EP2 PROTOTYPE FP1 PROTOTYPE FP2 etc Note: Refer to build Exemption and/or the Build Entry Request (BER) for the proper naming convention for the prototype Build. Line 3 is replaced with text "NOT FCC or TYPE APPROVED". Text height min 2 mm. Line 4 and 5: IMEI-numbers as barcode and IMEI-numbers as characters shall be filled with the test IMEI number. The test IMEI number is in the following ranges: (the CD number must be added) Line 9 is left blank

PAGE 1 OF 4 TTI-P-G 081/94-A0 Accredited according to ISO/IEC 17025 Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM Internal Photos FOR: Quad-Band GPRS module MODEL #: GR 64 Sony Ericsson Mobile Communications 7001 Development Drive RTP, Durham NC 27709 USA FCC ID: PY7BC051021 IC ID: 4170B-BC051021 REFERENCE TEST REPORT #: SONY1_001_06001_FCC22-24 DATE: MAY 12, 2006 PAGE 2 OF 4 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. Table of Contents 1 ASSESSMENT .................................................................................................................................... 3 2 INTERNAL PHOTOS ........................................................................................................................ 4 PAGE 3 OF 4 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. 1 Assessment The following is in compliance with the applicable criteria specified in FCC rules Parts 2, 22 and 24 of Title 47 of the Code of Federal Regulations and in compliance with the applicable criteria specified in Industry Canada rules RSS132 and RSS133. Company Description Model # Sony Ericsson Mobile Communications Quad-Band GPRS module GR 64 PAGE 4 OF 4 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. 2 INTERNAL PHOTOS

TTI-P-G 081/94-A0 Accredited according to ISO/IEC 17025 Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM FCC Test Report FCC Part 22,24 / RSS 132,133 FOR: Quad-Band GPRS module MODEL #: GR 64 Sony Ericsson Mobile Communications 7001 Development Drive RTP, Durham NC 27709 USA FCC ID: PY7BC051021 IC ID: 4170B-BC051021 TEST REPORT #: SONY1_001_06001_FCC22-24 DATE: MAY 12, 2006 Test Report #: SONY1_001_06001_FCC22-24 Date of Report: 2006-05-12 Page 2 of 101 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. Table of Contents 1 ASSESSMENT .................................................................................................................................... 4 2 ADMINISTRATIVE DATA............................................................................................................... 5 2.1 IDENTIFICATION OF THE TESTING LABORATORY ISSUING THE EMC TEST REPORT......................... 5 2.2 IDENTIFICATION OF THE CLIENT................................................................................................... 5 2.3 IDENTIFICATION OF THE MANUFACTURER.................................................................................... 5 3 EQUIPMENT UNDER TEST (EUT) ................................................................................................ 6 3.1 IDENTIFICATION OF THE EQUIPMENT UNDER TEST....................................................................... 6 3.2 IDENTIFICATION OF ACCESSORY EQUIPMENT............................................................................... 6 4 SUBJECT OF INVESTIGATION..................................................................................................... 7 5 MEASUREMENTS............................................................................................................................. 8 5.1 RF POWER OUTPUT....................................................................................................................... 8 5.1.1 FCC 2.1046 Measurements required: RF power output....................................................... 8 5.1.2 Limits: ................................................................................................................................... 8 5.1.2.1 FCC 22.913 (a) Effective radiated power limits. .............................................................. 8 5.1.2.2 FCC 24.232 (b)(c) Power limits. ....................................................................................... 8 5.1.3 Conducted Output Power Measurement procedure:............................................................. 8 5.1.4 Results 850 MHz band(conducted): ...................................................................................... 9 5.1.5 Results 1900 MHz band(conducted): .................................................................................... 9 5.1.6 Radiated Output Power Measurement procedure:.............................................................. 16 5.1.7 ERP Results 850 MHz band: ............................................................................................... 17 5.1.8 EIRP Results 1900 MHz band:............................................................................................ 17 5.2 OCCUPIED BANDWIDTH/EMISSION BANDWIDTH........................................................................ 24 5.2.1 FCC 2.1049 Measurements required: Occupied bandwidth............................................... 24 5.2.2 Occupied / emission bandwidth measurement procedure:.................................................. 24 5.2.3 Occupied / Emission bandwidth results 850 MHz band: .................................................... 25 5.2.4 Occupied / Emission bandwidth results 1900 MHz band: .................................................. 32 5.3 FREQUENCY STABILITY............................................................................................................... 39 5.3.1 Limit .................................................................................................................................... 39 5.3.2 FREQUENCY STABILITY (GSM-850) ............................................................................... 40 5.3.3 FREQUENCY STABILITY (PCS-1900) .............................................................................. 41 5.4 SPURIOUS EMISSIONS CONDUCTED............................................................................................. 42 5.4.1 FCC 2.1051 Measurements required: Spurious emissions at antenna terminals. .............. 42 5.4.2 Limits: ................................................................................................................................. 42 5.4.2.1 FCC 22.917 Emission limitations for cellular equipment. ............................................. 42 5.4.2.2 FCC 24.238 Emission limitations for Broadband PCS equipment. ............................... 42 5.4.3 Conducted out of band emissions measurement procedure: ............................................... 43 5.4.4 Bandedge Results GSM-850 ................................................................................................ 44 5.4.5 Conducted Spurious Results GSM-850 ............................................................................... 46 5.4.6 Bandedge Results PCS-1900 ............................................................................................... 50 5.4.7 Conducted Spurious Results PCS-1900 .............................................................................. 52 5.5 SPURIOUS EMISSIONS RADIATED...............................…

Text truncated - open the document above for the full version.

PAGE 1 OF 12 TTI-P-G 081/94-A0 Accredited according to ISO/IEC 17025 Bluetooth Qualification Test Facility (BQTF) FCC listed# 101450 IC recognized # 3925 CETECOM Inc. 411 Dixon Landing Road Š Milpitas, CA 95035 Š U.S.A. Phone: + 1 (408) 586 6200 Š Fax: + 1 (408) 586 6299 Š E-mail: [email protected] Š http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Board of Directors: Dr. Harald Ansorge, Dr. Klaus Matkey, Hans Peter May © Copyright by CETECOM Test Setup Photos FOR: Quad-Band GPRS module MODEL #: GR 64 Sony Ericsson Mobile Communications 7001 Development Drive RTP, Durham NC 27709 USA FCC ID: PY7BC051021 IC ID: 4170B-BC051021 REFERENCE TEST REPORT #: SONY1_001_06001_FCC22-24 DATE: MAY 12, 2006 PAGE 2 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. Table of Contents 1 ASSESSMENT .................................................................................................................................... 3 2 TEST SETUP PHOTOS ..................................................................................................................... 4 PAGE 3 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. 1 Assessment The following is in compliance with the applicable criteria specified in FCC rules Parts 2, 22 and 24 of Title 47 of the Code of Federal Regulations and in compliance with the applicable criteria specified in Industry Canada rules RSS132 and RSS133. Company Description Model # Sony Ericsson Mobile Communications Quad-Band GPRS module GR 64 PAGE 4 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. 2 TEST SETUP PHOTOS RADIATED EMISSIONS PAGE 5 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. RADIATED EMISSIONS PAGE 6 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. RADIATED EMISSIONS PAGE 7 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. RADIATED EMISSIONS PAGE 8 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. RADIATED EMISSIONS PAGE 9 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. AC LINE CONDUCTION PAGE 10 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. AC LINE CONDUCTION PAGE 11 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. FREQ/TEMP PAGE 12 OF 12 This report shall not be reproduced except in full without the written approval of: CETECOM, Inc. ANTENNA PORT MEASURMENTS