PY7PM-0020Mobile phone with Bluetooth, WLAN 802.11abgn, GPS/A-GPS, RFID and FM Rx

’12.2 INSTRUCTION MANUAL Introduction Thank you for your purchase of "SO-05D". For proper use of the SO-05D, read this manual carefully before and while you use the SO-05D. Before using the terminal SO-05D supports W-CDMA, GSM/GPRS and Wireless LAN Systems. Because a terminal operates using radio frequencies, it cannot be used inside a tunnel, underground, in a building or other locations where radio waves do not reach the terminal, in locations with weak radio wave condition, or outside of the FOMA's service area. The services may not be available on high upper floors of high-rise apartments or buildings, even if you can see no obstructions around you. On occasion, your calls may become disconnected even in areas with strong radio wave condition, even if you are not moving, or even if there are 4-antenna marks in the terminal's display. Note that because the terminal operates on radio frequencies, your calls are at risk of being intercepted by the third party. However, the W-CDMA, GSM/GPRS system automatically scrambles all calls through a private call feature. Therefore, even if third party successfully intercepts your call, they will only hear noise. The terminal operates on radio frequencies by converting voice into digital signals. If the caller moves into an area of adverse radio wave condition, the digital signal may not be restored accurately, and the voice received in the call may differ slightly from the actual voice. Note down the information saved in the terminal in a separate note and keep it safely. Even if the data may be lost as a result of malfunction, repair, change, or other handling of the terminal, under no condition will DOCOMO be held liable for any lost data saved in the terminal. You are recommended to save important data to microSD card. As with PCs, some user-installed applications may disrupt the stability of the terminal performance, or unexpectedly transmit information via the Internet causing improper use of your location information as well as personal information recorded on the terminal. Therefore, verify the supplier and operating conditions of the applications to be used before using them. This terminal has FOMA Plus-Area and FOMA HIGH-SPEED Area support. Descriptions in this manual are fore the terminal with a DOCOMO's UIM inserted. SIM unlock This terminal supports SIM unlock. If you release SIM lock, you can use SIM by a carrier other than NTT DOCOMO. The SIM unlock service is provided at a docomo Shop. A SIM unlock charge is separately required. If you use a SIM other than by DOCOMO, available services and functions will be limited. DOCOMO is not liable to any failures or malfunctions. For details of SIM unlock, refer to NTT DOCOMO website. 1 SO-05D (with warranty) (Quick Start Guide) (In Japanese only) SO-05D (Notes on usage Safety/Handling precautions) (In Japanese only) AC Adapter Cable SO04 (with warranty) 1Seg antenna cable SO01 (with manual) microSD card (2GB) * (Sample) (with manual) * Inserted in the terminal when purchased. Stereo Headset with Microphone (Sample) (with manual) For details on optional devices, see "Optional and related devices" (P.243). Supplied accessories Supplied accessories <AC adapter><microUSB cable> 2 In addition to this manual, the operations of SO-05D are described in " (Quick Start Guide)" (in Japanese only) and "Instruction Manual" application of the terminal. The initial operations and settings after purchasing the terminal, screen view contents and operations of main function are explained. (In Japanese only) Similarly to this manual, operations and settings of each function are explained. To use "Instruction Manual" application, from the Home screen, u Tap [Instruction Manual]. For the first time using, download and install it according to the onscreen instructions. You can use the application as an electronic book. You can also shift to actual operations by tapping the description in the contents or view reference contents. ❖ Note For downloading or updating the application, a high packet communication charge will be applied because of a large amount data communication. For this reason, subscription of packet flat-rate service is highly recommended. * If you use Wi-Fi function to download, packet communication charges are not applied. Operations and settings of each function are explained. It can be downloaded from NTT DOCOMO website. http://www.nttdocomo.co.jp/english/ support/trouble/manual/download/ index.html * You can download the latest information of " (Quick Start Guide)" (in Japanese only). The URL and contents are subject to change without prior notice. ❖ Note Reproduction or reprint of all or part of this manual without prior permission is prohibited. Important information for SO-05D is posted in the following website. Be sure to check before using. http://www.sonymobile.co.jp/support/use_support/ product/so-05d/ About manuals of SO-05D " (Quick Start Guide)" (Supplied accessories) "Instruction Manual" (Application of the terminal) "Instruction Manual" (PDF file) 3 In this manual, each key operation is described with p , x , y , t , m , k . And selection operations of the icons or function items on the touch panel are described as follows. ❖ Information In this manual, the instructions are described with the default Home screen. If you set the other application to the home screen, the operations may differ from the descriptions. Display examples and illustrations used in this manual are just images for explanations and may be different from actual ones. In this manual, the easier procedure is described for the functions and settings which have multiple operating procedures. Please note that "SO-05D" is called "the terminal" in this manual. In this manual, explanations for "docomo" as Home application are provided. To switch the Home applications, see "Learning Home screen" (P.66). Operation descriptions DescriptionOperation From the Home screen, tap t and tap [Settings]. From the Home screen, tap t…

Text truncated - open the document above for the full version.

SONY Sony Mobile Communications SE-2.21 88 LUND· SWEDEN Confidentiality Request 2012-06-13 CGQBDA12200 SEMC/CGQBDA Afrah Sadiq +46 10 80 12250 Receiver Federal Communications Commission Subject: Request for Confidentiality FCC 10: PY7PM-0020 To Whom It May Concern : In accordance with §0.459 of CFR 47, Sony Mobile Communications AB requests confidentiality for the below listed items for our Sony mobile phone type PM-0020-BV, FCC 10: PY7PM-0020: 1. B:lock Diagram 2. Schematic Diagram 3. Part List 4 . OperationallTechnical Descriptions These items contain detailed system and equipment description and related information about the product which Sony Mobile Communications AB considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Mobile Communications AB also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Afrah Sadiq Staff Verification Engineer Global Type Approval Sony Mobile Communications Nya Vattentornet 221 88 Lund, Sweden Fax: +46 10 80 02441 sonyericsson.com Sony Mobile Communications Styrelsens slite: Lund Momsnr' V,A.TNo: SE556615665801 Registered office: Lund Orgamsationsnr • Reg No: 556615-6658 Postadress • Mail Besoksadress • Office address Telefon • Telephone Telefax • Telefax SE-221 sa Lund Nya Vattentornet Nat 010·8000000 Nat 010-80 02().40 Sweden LLlnd Int +46 10 80 00000 Int +46 108002040

Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 153 of 171 An ne x B E x te rna l ph ot ogra phs o f the E UT Photo documentation: Photo 1: Photo 2: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 154 of 171 Photo 3: Photo 4: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 155 of 171 Photo 5: Photo 6:

Company Internal MARKING DRAWINGLABEL CONTENT 1 (4) Prepared (also subject responsible if other) No. Leif Hedin (23056584) 1266-6107 Approved Checked Date Rev Reference Leif Hedin (23056584) 2012-05-31 2 5State: Released Label Content Specification SO-05D Mobile Phone Orange 1 General information 2 Printing information Content Format Line 1 (2,5/1,0) Sony stylized name. Graphics, height 1,5 mm. According to 1263-9535. Line 2 (4,5/1,0) Operator logo in Japanese Graphics, height 1,5 mm. According to 1234-3760 Line 3a (6,5/1,0) “Product name in Japanese Graphics, height 1,5 mm. According to 1234-3743 Line 3b (6,7/9,0) Model Name “SO-05D” Text, height 1,5 mm. According to Chapter 1 in MLCI Line 4 (9,0/1,0) Colour of the included telephone, in English: e.g. “< Orange >” Text, height 1,5 mm. English colour names, if exchange PBA the color is “PBA”, according to Chapter 2.1 in MLCI. Line 5 (10,5/1,0) Product number of the Sales Item in which the phone is packed, if applicable. “SI XXXX-XXXX” Text, height 1,2 mm. Line 6 (13,0/1,0) Supplier’s identification for trace-ability of the telephone, as desired by supplier (e.g. “S/N: nnn....” for serial number). Text, height 1,2 mm. Defined by supplier. Mobile Phone label part no  1261-3276 Mobile Phone label content part no  1266-6106 Bar code  Print quality: according to COSMETIC GUIDELINE – Bar code labels document 1222-6072 Uen  Quiet zone: No bar codes are allowed to be closer to a label edge than 2 mm! Text If applicable, or nothing else specified, Zebra printer Scaleable Smooth Font Arial Narrow is imposed. When needed, the text is adjusted to fit the label. Coordinates “(x/y)” under each line number specifies the bottom / left alignment for text, graphics and bar codes, x is measured vertically, and y horizontally from the upper left corner of the label (landscape format), both in mm. When needed, the alignment is adjusted to fit the label. Company Internal MARKING DRAWINGLABEL CONTENT 2 (4) Prepared (also subject responsible if other) No. Leif Hedin (23056584) 1266-6107 Approved Checked Date Rev Reference Leif Hedin (23056584) 2012-05-31 2 5State: Released Line 7a (15,5/1,0) Production week (flash), “yyWww/” (yy = year, ww = week) Text, height 1,5 mm. Line 7b (15,5/8,0) Production date in Japanese (eg: year+ 年+ month+月 ) : “ 20XX 年 XX 月” Text, height 1,5 mm. Graphics, height 1,5 mm. According to 1234-3763, 1235- 6102 and 1235-6103 Line 8a (17,0/1,0) Type number of the phone, “TYPE: PM-0020-BV”. Text, height 1,2 mm. According to Chapter 1 in MLCI. Line 8b (17,0/16,5) HW & SW identification field, if applicable; “EFF” Text, height 1,2 mm. According to Type-testing report under Product Model Specifying Document Line 8c (17,0/22,5) Location code of where the phone is flashed, if applicable, “XXX” Text, height 1,2 mm. Line 9 (18,5/1,0) “FCC ID: PY7PM-0020” Text, height 1,2 mm. According to Chapter 1 in MLCI Line 10 (19,8/1,0) “製 “+ Actual electronic serial number (IMEI) of the Mobile Phone, “製 00000000-000000-0” Graphics, height 1,2 mm. According to 1234-3770. Text, height 1,2 mm. In the format TAC-SNR-CD.TAC and SNR derived from pos 500 in BOM. CD = check digit according to the Luhn formula (ISO/IEC 7812), GSM 02.16. Line 11 (24,5/2,0) Line 10 in bar code. As desired by supplier (e.g. only actual number). Bar code, height 4,5 mm. As desired by supplier (e.g. Code 128 symbology). Line 12a (29,8/1,0) “CE approval symbol, The notified body number 0682 and Alert Symbol” Graphics, height 5 mm. According to 1242-7470 Line 12b (29,8/30,5) WEE trashcan without bar symbol Graphics, min. height 5mm, according to 1202-5537 Line 12c (29,8/36,0) “Li-ion 00 Symbol” Graphics, min. height 5,0 mm, according to 1235-2267 Line 13a (33,0/1,0) “Caution symbol” Graphics, height 2,5 mm. According to 1234-3774 Line 13b (33,0/4,5) “Caution” in Japanese Graphics, height 2.5 mm. According to 1234-3790 Line 13c (33,0/10,5) “Do not remove this label” statement in Japanese, on two rows. Graphics, height for each row 1,5 mm. According to 1250-5471 Company Internal MARKING DRAWINGLABEL CONTENT 3 (4) Prepared (also subject responsible if other) No. Leif Hedin (23056584) 1266-6107 Approved Checked Date Rev Reference Leif Hedin (23056584) 2012-05-31 2 5State: Released Line 14 (36,2/1,0) Manufacturer name in Japanese ” ” Graphics, height 1,5 mm. According to 1264-5801, on two rows Line 15 (38,8/27,8) Local Type Approval Number: T AD 12-0015 202 Text, height 1,2 mm Line 16 (39,0/27,2) Square around T above, see Line 14 Width 1,5 x Height 2,0 mm Line 17 (41,2/27,8) Local Type Approval Number: R 202-SMA019 Text, height 1,2 mm. Line 18a (41,5/1,0) “Bluetooth value” logotype Graphics, min. height 4,5 mm. According to 1262-0427. Line 18b (41,5/19,5) “JATE” logo Graphics, height 5 mm. According to 1234-3837 Line 18c (41,5/27,2) Square around R above, see Line 16 Width 1,5 x Height 2,0 mm Line 19a (44,5/1,0) Marking of origin. “Made in Xxx”; “Xxx” = actual country of production of the included telephone, in English Text, height 1,2 mm. Line 19b (44,5/17,5) WiFi certified -logo Graphics height 2,5 mm, According to 1264-8500 Line 19c (44,5/22,0) WLAN text in Japanese Graphics height 2,5 mm, or text, Character height 1,2 mm. According to 1262-5051 Company Internal MARKING DRAWINGLABEL CONTENT 4 (4) Prepared (also subject responsible if other) No. Leif Hedin (23056584) 1266-6107 Approved Checked Date Rev Reference Leif Hedin (23056584) 2012-05-31 2 5State: Released 3 Layout The conceptual picture (for Zebra 90XiII printer, or equivalent) should not be considered as specifications, but as an additional help for setting up the label. 3.1 Conceptual picture double underlined = major changes since last revision.

Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 156 of 171 An ne x C Inte r na l p ho to gra phs o f the E UT Photo documentation: Photo 1: Photo 2: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 157 of 171 Photo 3: Photo 4: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 158 of 171 Photo 5: Photo 6: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 159 of 171 Photo7: Photo 8: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 160 of 171 Photo 9: Photo 10: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 161 of 171 Photo 11: Photo 12: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 162 of 171 Photo 13 Photo 14: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 163 of 171 Photo 15: Photo 16: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 164 of 171 Photo 17: Photo 18: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 165 of 171 Photo 19: Photo 20: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 166 of 171 Photo 21: Photo 22: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 167 of 171 Photo 23: Photo 24: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 168 of 171 Photo 25: Photo 26: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 169 of 171 Photo 27: Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 170 of 171 An ne x D Doc u me n t his to r y Version Applied changes Date of release 1.0 Initial release 2012-06-06 -A New summary 2012-06-18 -B IC certification number removed 2012-06-26 An ne x E Fur the r in for ma ti o n Glossary AVG - Average DUT - Device under test EMC - Electromagnetic Compatibility EN - European Standard EUT - Equipment under test ETSI - European Telecommunications Standard Institute FCC - Federal Communication Commission FCC ID - Company Identifier at FCC HW - Hardware IC - Industry Canada Inv. No. - Inventory number N/A - Not applicable PP - Positive peak QP - Quasi peak S/N - Serial number SW - Software

Page 1 of 203 TEST REPORT Test Report No.: 1-4254/12-32-02-D Testing Laboratory Applicant CETECOM ICT Services GmbH Untertürkheimer Straße 6 – 10 66117 Saarbrücken/Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Test Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-01 Sony Mobile Communications AB Nya Vattentornet 22188 Lund/SWEDEN Phone: +46 46 19 30 00 Contact: Håkan Sjöberg e-mail: [email protected] Phone: +46 46 19 35 59 Fax: +46 46 19 32 95 Manufacturer Sony Mobile Communications AB Nya Vattentornet 22188 Lund/SWEDEN Test Standard/s IEEE 1528-2003 Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR)in the Human Head from Wireless Communications Devices: Measurement Techniques OET Bulletin 65 Supplement C Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields RSS-102 Issue 4 Radio Frequency Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Mobile Phone Device type: portable device Model name: PM-0020-BV S/N serial number: CB5A1K2Z8Z / CB5A1K2Z88 / CB5A1K3QFD FCC-ID: PY7PM-0020 IMEI-Number: 00440245-026130-4 / 00440245026138-7 00440245-027057-8 (for WLAN) Hardware status: AP1 Software status: 7.0.A.0.649 / s_atp_blue_0_0_37_0_c (for WLAN) Frequency: see technical details Antenna: integrated antenna Battery option: Li-ion battery BA700 3.7V / 1500mAh Accessories: Stereo headset Test sample status: identical prototype Exposure category: general population / uncontrolled environment This test report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test Report authorised: Test performed: Thomas Vogler Oleksandr Hnatovskiy Senior Testing Manager Testing Manager Test report no.: 1-4254/12-32-02-D Page 2 of 203 1 Table of contents 1 Table of contents ....................................................................................................................................... 2 2 General information .................................................................................................................................. 4 2.1 Notes and disclaimer ..................................................................................................................... 4 2.2 Application details ......................................................................................................................... 4 2.3 Statement of compliance ............................................................................................................... 4 2.4 Technical details............................................................................................................................. 5 3 Test standards/ procedures references .................................................................................................. 6 3.1 RF exposure limits ......................................................................................................................... 7 4 Summary of Measurement Results ......................................................................................................... 8 5 Test Environment ...................................................................................................................................... 8 6 Test Set-up ................................................................................................................................................. 9 6.1 Measurement system ..................................................................................................................... 9 6.1.1 System Description ................................................................................................................ 9 6.1.2 Test environment ................................................................................................................. 10 6.1.3 Probe description ................................................................................................................. 10 6.1.4 Phantom description ............................................................................................................ 11 6.1.5 Device holder description .................................................................................................... 11 6.1.6 Scanning procedure ............................................................................................................ 12 6.1.7 Spatial Peak SAR Evaluation .............................................................................................. 13 6.1.8 Data Storage and Evaluation............................................................................................... 14 6.1.9 Tissue simulating liquids: dielectric properties .................................................................... 16 6.1.10 Tissue simulating liquids: parameters ................................................................................. 17 6.1.11 Measurement uncertainty evaluation for SAR test .............................................................. 18 6.1.12 Measurement uncertainty evaluation for SAR test > 3 GHz ............................................... 19 6.1.13 Measurement uncertainty evaluation for system check ...................................................... 20 6.1.14 Measurement uncertainty evaluation for system check > 3 GHz ........................................ 21 6.1.15 System check ..........................…

Text truncated - open the document above for the full version.

Page 1 of 84 Annex D Appendix to Test Report No.: 1-4254/12-32-02-D Testing Laboratory CETECOM ICT Services GmbH Untertürkheimer Straße 6 – 10 66117 Saarbrücken/Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Test Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-01 Appendix with Calibration data, Phantom certificate and system validation information Annex D to Test report no.: 1-4254/12-32-02-D Page 2 of 84 1 Table of contents 1 Table of contents ....................................................................................................................................... 2 2 Calibration report “Probe ET3DV6” ......................................................................................................... 3 3 Calibration report “Probe ET3DV6” ....................................................................................................... 14 4 Calibration report “Probe EX3DV4” ...................................................................................................... 25 5 Calibration report “900 MHz System validation dipole” ...................................................................... 36 6 Calibration report “1900 MHz System validation dipole” .................................................................... 44 7 Calibration report “2450 MHz System validation dipole” .................................................................... 52 8 Calibration report “5GHz System validation dipole” ........................................................................... 60 9 Calibration report “5GHz System validation dipole” ........................................................................... 68 10 Calibration certificate of Data Acquisition Unit (DAE) ................................................................. 76 11 Calibration certificate of Data Acquisition Unit (DAE) ................................................................. 77 12 Certificate of “SAM Twin Phantom V4.0/V4.0C’’ .......................................................................... 78 13 Application Note System Performance Check .............................................................................. 79 13.1 Purpose of system performance check ................................................................................. 79 13.2 System Performance check procedure .................................................................................. 79 13.3 Uncertainty Budget ................................................................................................................... 80 13.4 Power set-up for validation ...................................................................................................... 83 13.5 Laboratory reflection ................................................................................................................ 84 13.6 Additional system checks ........................................................................................................ 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 3 of 84 2 Calibration report “Probe ET3DV6” Annex D to Test report no.: 1-4254/12-32-02-D Page 4 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 5 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 6 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 7 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 8 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 9 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 10 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 11 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 12 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 13 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 14 of 84 3 Calibration report “Probe ET3DV6” Annex D to Test report no.: 1-4254/12-32-02-D Page 15 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 16 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 17 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 18 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 19 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 20 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 21 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 22 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 23 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 24 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 25 of 84 4 Calibration report “Probe EX3DV4” Annex D to Test report no.: 1-4254/12-32-02-D Page 26 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 27 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 28 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 29 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 30 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 31 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 32 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 33 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 34 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 35 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 36 of 84 5 Calibration report “900 MHz System validation dipole” Annex D to Test report no.: 1-4254/12-32-02-D Page 37 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 38 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 39 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 40 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 41 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 42 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page 43 of 84 Annex D to Test report no.: 1-4254/12-32-02-D Page …

Text truncated - open the document above for the full version.

2012-06-26 Page 1 of 171 TEST REPORT Test report no.: 1-4254/12-24-08-B Testing laboratory Applicant CETECOM ICT Services GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-01 Area of Testing: Radio/Satellite Communications Sony Mobile Communications AB Nya Vattentornet 22188 Lund / SWEDEN Phone: +46 46 19 30 00 Fax: +46 46 19 32 95 Contact: Håkan Sjöberg e-mail: [email protected] Phone: +46 46 19 35 59 Manufacturer Sony Mobile Communications AB Nya Vattentornet 22188 Lund / SWEDEN Test standard/s 47 CFR Part 15 Title 47 of the Code of Federal Regulations; Chapter I Part 15 - Radio frequency devices RSS - 210 Issue 8 Spectrum Management and Telecommunications - Radio Standards Specification Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: GSM Mobile Phone GPRS/EGPRS 850/900/1800/1900; UMTS FDDI/FDDV/FDDVI/FDDXIX; HSPA; LTE Band 1; BT3.1; WLAN a/b/g/n; AGPS; RFID, FM Rx Model name: PM-0020-BV FCC ID: PY7PM-0020 IC: Frequency: ISM band 5150 MHz to 5250 MHz; 5250 MHz to 5350 MHz and 5470 MHz to 5725 MHz Technology tested: WLAN (OFDM → a – mode / n – mode HT20 & n – mode HT40) Antenna: Integrated antenna Power Supply: 3.7 V DC by Li - ion battery Temperature Range: -20°C to +55 °C Test report authorised: Test performed: 2012-06-26 Andreas Luckenbill 2012-06-26 Marco Bertolino Testing Manager Test report no.: 1-4254/12-24-08-B 2012-06-26 Page 2 of 171 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes and disclaimer ................................................................................................................…

Text truncated - open the document above for the full version.