PY7PM-0220GSM/UMTS/LTE Mobile Phone with WLAN, BT, RFID

United States This phone model has been certified in compliance with the government's requirements for exposure to radio waves. The SO-02E mobile phones have been designed to comply with applicable safety requirements for exposure to radio waves. Your wireless phone is a radio transmitter and receiver. It is designed to not exceed the limits* of exposure to radio frequency (RF) energy set by governmental authorities. These limits establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by international scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands. While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. For more information on SAR, please refer to the safe and efficient use chapter in the User Guide. The highest SAR value as reported to the authorities for this phone model when tested for use by the ear is . W/kg*, and when worn on the body is . W/kg* for speech and . W/kg* for data calls. For body-worn operation, this phone has been tested and meets the FCC RF exposure guidelines. Please use an accessory designated for this product or an accessory which contains no metal and which positions the handset a minimum of 1.5 cm from the body. For devices which include "WiFi hotspot" functionality, SAR measurements for the device operating in WiFi hotspot mode were taken using a separation distance of 10 mm. Use of third-party accessories may result in different SAR levels than those reported. Radio Wave Exposure and Specific Absorption Rate (SAR) Information ** Before a phone model is available for sale to the public in the US, it must be tested and certified by the Federal Communications Commission (FCC) that it does not exceed the limit established by the government-adopted requirement for safe exposure*. The tests are performed in positions and locations (i.e., by the ear and worn on the body) as required by the FCC for each model. The FCC has granted an equipment authorization for this phone model with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. While there may be differences between the SAR levels of various phones, all mobile phones granted an FCC equipment authorization meet the government requirement for safe exposure. SAR information on this phone model is on file at the FCC and can be found under the display grant section of http:// www.fcc.gov/oet/ea/fccid/ after searching on FCC ID PY7PM-0220. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) website at http:// www.ctia.org/. *In the United States, the SAR limit for mobile phones used by the public is 1.6 watts/ kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements. **This paragraph is only applicable to authorities and customers in the United States. Europe This mobile phone model SO-02E has been designed to comply with applicable safety requirements for exposure to radio waves. These requirements are based on scientific guidelines that include safety margins designed to assure the safety of all persons, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate, or SAR. Tests for SAR are conducted using standardized methods with the phone transmitting at its highest certified power level in all used frequency bands. While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. For more information on SAR, please refer to the safety chapter in the User's Guide. SAR data information for residents in countries that have adopted the SAR limit recommended by the International Commission of Non-lonizing Radiation Protection (ICNIRP), which is 2 W/kg averaged over ten (10) gram of tissue (for example European Union, Japan, Brazil and New Zealand): The highest SAR value for this model phone tested by Sony Mobile Communications AB for use at the ear is . W/kg (10g). This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: Any change or modification not expressly approved by Sony Mobile Communications AB may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC …

Text truncated - open the document above for the full version.

INSTRUCTION MANUAL Introduction Thank you for your purchase of "SO-02E". For proper use of the SO-02E, read this manual carefully before and while you use the SO-02E. About manuals of SO-02E In addition to this manual, the operations of SO-02E are described in " (Quick Start Guide)" (in Japanese only) and "Instruction Manual" application of the terminal (in Japanese only). " (Quick Start Guide)" (Supplied accessories) The initial operations and settings after purchasing the terminal, screen view contents and operations of main function are explained. (In Japanese only) "Instruction Manual" (Application of the terminal) Similarly to this manual, operations and settings of each function are explained. To use "Instruction Manual" application, from the Home screen, tap and [Instruction Manual]. When using for the first time or reinstalling, download and install the application according to the onscreen instructions. You can use the application as an electronic book. You can also shift to actual operations by tapping the description in the contents or view reference contents. (In Japanese only) ❖ Note For downloading or updating the application, a high packet communication charge will be applied because of a large amount data communication. For this reason, subscription of packet flat-rate service is highly recommended. * If you use Wi-Fi function to download, packet communication charges are not applied. "Instruction Manual" (PDF file) Operations and settings of each function are explained. It can be downloaded from NTT DOCOMO website. http://www.nttdocomo.co.jp/english/support/ trouble/manual/download/index.html * You can download the latest information of " (Quick Start Guide)" (in Japanese only). The URL and contents are subject to change without prior notice. ❖ Note Reproduction or reprint of all or part of this manual without prior permission is prohibited. Important information for SO-02E is posted in the following website. Be sure to check before using. http://www.sonymobile.co.jp/support/use_support/ product/so-02e/ (in Japanese only) for docomo with series "Tips of smartphone for docomo with series" (Widget in the terminal) An widget with which you can easily learn useful functions and basic operations you should know with Docomodake. To use Tips of smartphone for docomo with series, from the Home screen, tap . 1 Operation descriptions In this manual, each key operation is described with p , x , y , r , m . And selection operations of the icons or function items on the touch panel are described as follows. ❖ Information In this manual, the instructions are described with the default Home screen. If you set the other application to the home screen, the operations may differ from the descriptions. Display examples and illustrations used in this manual are just images for explanations and may be different from actual ones. In this manual, the easier procedure is described for the functions and settings which have multiple operating procedures. Please note that "SO-02E" is called "the terminal" in this manual. In this manual, explanations for "docomo" as Home application are provided. To switch the Home applications, see "Learning Home screen" (P.60). DescriptionOperation From the Home screen, tap and tap [Settings] u [About phone]. From the Home screen, tap (Applications button), and then tap "Settings" on the next screen and "About phone" on the following screen in order. Touch and hold an icon. Keep touching an icon longer (1- 2 seconds). 2 (Quick Start Guide) (In Japanese only) SO-02E (Notes on usage Safety/Handling precautions) (In Japanese only) Battery Pack SO06 1Seg antenna cable SO01 (with manual) microSD card (2GB) * (Sample) (with manual) * Inserted in the terminal when purchased. Stereo Headset with Microphone (Sample) (with manual) For details on optional devices, see "Optional and related devices" (P.231). Supplied accessories Supplied accessories SO-02E (with warranty)Back cover SO20 Contents/Precautions 3 Contents Supplied accessories. . . . . . . . . . . . . . . . . 2 About using the terminal . . . . . . . . . . . . 5 Safety Precautions (Always follow these directions) . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Handling precautions . . . . . . . . . . . . . . . 16 Before Using the Terminal . . . 22 Part names and functions................................................ 22 docomo mini UIM card ..................................................... 23 microSD card ........................................................................... 24 Battery pack .............................................................................. 25 Charging ..................................................................................... 26 Turning power on/off......................................................... 30 Initial settings (Setup guide) .......................................... 31 Status bar ................................................................................... 33 Notification panel ................................................................. 35 Notification LED ..................................................................... 36 Basic operations ..................................................................... 36 Searching information in the terminal and web pages ............................................................................................ 39 Character entry ....................................................................... 40 Setting character entry ...................................................... 53 Setting Japanese keyboard............................................. 53 USB keyboard/Bluetooth keyboard ........................... 59 docomo Palette UI. . . . . . . . . . . 60 Home screen............................................................................ 60 Application screen................................................................ 66 Phone . . . . . . . . . . . . . . . . . . . . . . 77 …

Text truncated - open the document above for the full version.

SONY Sony Mobile Communications SE-221 88 LUND· SWEDEN Confidentiality Request 2012-11-29 CGQBDA 12:469 SoM/CGQBDA Afrah Sadiq +46 10 80 12250 Receilver Federal, Communications Commission Subject: Request for Confidentiality FCC 10: PY7PM-0220 To Whom It May Concern: In accordance with §0.459 of CFR 47, Sony Mobile Communications AB requests confidentiality for the below listed items for our Sony mobile phone type PM-0220-BV, FCC 10: PY7PM-0220: 1. Block D.iagram 2 . Schematic Diagram 3. Part List 4. Operational/Technical Descriptions These items contain detailed system and equipment description and related information about the product which Sony Mobile Communications AB considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Mobile Communications AB also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, .­ ~-,=- ~ Afrah Sadiq S aft VenficatiQil Engme.e·· Global Typ~~ f.I.pproval Sony Mobile Cammunictltlon N1'<1 VaUtlntomel 221 88 Lund, Sweden F<lX: +46 10 no 02441 SQl)ymQbjl .mill Sony Mobile Communications Styrelsens sale: lJJnd Momsnr. II.A T.No: SE55661566S801 Registered office Lund Orgenisationsnr • Reg No: 556615-B658 Postadress • Mail Bes6k.sadress • Office address TeJefan • Te1ephone Telefal< • Telefax S6--221 88 lUrid Nya Vattentomel Nat 010-80 00000 Nat 010-80 02040 Sweden lund Int +46 10 80 00000 Int io46 1 0 80 02040

SONY Sony Mobile Communications SE-221 88 LUND· SWEDEN Short Term Confidentiality Request 2012-12-04 CGQBOA 12:483 SoMC! CGQBOA Afrah Sadiq +46 10 80 12250 Receiver Federal Communications Commission Subject: Request for Temporary Confidentiality FCC ID: PY7PM-0220 To Whom It May Concern: I n accordance with §0.459 of CFR 47 and Public Notice OA 04-1705, Sony Mobile Communications AB requests in addition to confidentiality request CGQBOA 12:475 temporary confidentiality for 180 days of the below listed items for our mobile phone type PM-0220-BV, FCC 10: PY7PM-0220: 1. User Manual 2. Test set-up 3. External and Internal photos When the announcement of the product is done, the TCB will be notified to remove the Short Term Confidentiality. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, .. ~ Afrah Sadiq Staff Verification Engineer Global Type Approval Sony Mobile Communications NyB Vatlefl!orrwt 221 88 Lund, Swedon Fax: +46 10 80 02441 Sony Mobile Communications Styrelsens sate: Lund Mornsnr. VA TNa: SE556615665801 Registered office: Lund Organisationsnr' Reg No, 556015-6658 Postadless • Mfiil Besi:iksadress • Office address Telefon • Tel phone Telefax • Teleral< SE-221 88 Lund Nya Vattentornet Nat 010-80 00000 Nat 010-80 02040 Sweden Lund Int +46 10 8000000 Int +461060 02040

Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 20 of 30 An ne x B E x te rna l ph ot ogra phs o f the E UT Photo documentation: Photo 1: Photo 2: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 21 of 30 Photo 3: Photo 4: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 22 of 30 Photo 5: Photo 6:

Company Internal MARKING DRAWING 1 (5) Prepared (also subject responsible if other) No. SEM/CGOVDPLG, Anna Englund 1265-5198 Uen Approved Checked Date Rev Reference SEM/CGOVDPLG, Anna Englund 2012-04-20 1 1 SO-02E, Label Cont Sales Item, NTT Docomo, JP, Black, 45x80mm and label 42x10 mm and label 70.8 x 25.8 mm The text on the label shall be parallel to the short side. The label shall be placed on the Sales Item-box as shown in the Label Placing Instruction. 1.1 General information Sales Item label part no 1265-1000 45,0 x 80,0 mm (± 0,5 mm) + label 42x10 mm directly under the top label with a perforation only on the labels + 70,8 x 25,8 mm (± 0,5 mm) Bar code  Print quality: according to COSMETIC GUIDELINE – Bar code labels document 1222-6072 Uen  Quiet zone: No bar codes are allowed to be closer to a label edge than 4 mm! Text If applicable, or nothing else specified, Zebra printer Scaleable Smooth Font Arial Narrow is imposed. When needed, the text is adjusted to fit the label. Coordinates “(x/y)” under each line number specifies the bottom / left alignment for text, graphics and bar codes, x is measured vertically, and y horizontally from the upper left corner of the label (landscape format), both in mm. When needed, the alignment is adjusted to fit the label. MLCI = Main Label Content Info document. 1.2 Printing information Content Format Line A1, a (6,8/15,3) Model name, “SO-02E” Text, height 4 mm. According to Chapter 1 in MLCI. Line A1, b (6,8/35,0) Colour of the included telephone, in English; “Black” Text, height 3 mm. English colour names according to Chapter 2.1 in MLCI. Line A1, c (6,8/48,7) Colour code of the included telephone; “<K>“ Text, height 3 mm. <K>=Black Line A2 (13,0/13,5) “Mobile Phone” + Frequency band GSM/GPRS/EDGE 850/900/1800/1900& UMTS/HSPA Bands 1/5/6/19 & LTE Bands 1/19/21” Text, height 2 mm. Paragraph of two rows. According to Chapter 1 in MLCI. Company Internal MARKING DRAWING 2 (5) Prepared (also subject responsible if other) No. SEM/CGOVDPLG, Anna Englund 1265-5198 Uen Approved Checked Date Rev Reference SEM/CGOVDPLG, Anna Englund 2012-04-20 1 Content Format Line A3 (16,5/15,0) Actual product number, including R- state, followed by the language codes of the included user manuals; “SI XXXX-XXXX.X JA” Text, height 2,5 mm, language codes according to ISO 639 (Ericsson document 0012–084 Uen). Simplified Chinese = ZS, Traditional Chinese (Hong Kong) = ZH and Traditional Chinese (Taiwan) = ZT. The actual codes can be found in the description of the included set of documents. Line B1 (20,5/15,0) Supplier’s identification for trace- ability of the included telephone, as desired by supplier (e.g. “S/N: nnn....” for serial number). Text, height 2 mm. Defined by supplier. Line B2 (27,5/17,5) Line B1 in bar code. As desired by supplier (e.g. only actual number, with data identifier). Bar code, height 6 mm. As desired by supplier (e.g. Code 128 symbology). Line B3 (31,0/15,0) “製 “+ Actual electronic serial number (IMEI) of the Mobile Phone, “ 製00000000-000000-0” Graphics, height 2,6 mm. According to 1234-3770. Text, height 2,0 mm. Supplied by system. Line B4 (38,5/16,5) Line B3 in bar code (only actual number, without data identifier). Bar code, height 7 mm. Code 39 symbology, code C subset. If uneven number of digits, code B subset shall be used for the last digit. Line C1 (60,0/15,0) “JAN” Text, height 2 mm Line C2 (63,0/15,0) EAN/JAN13 number in bar code with number in text-en-clair; “0000000000000” Bar code, height 19 mm incl. text-en- clair (actual bar code 13 mm), EAN13 symbology. Line C3 (66,0/15,5) Customer code: “Product code: XXX00000” Text, height 2 mm Line C4 (71,0/16,5) Line C3 in bar code. (Only actual number, with data identifier). Bar code, height 7 mm. Code 39 symbology Line C5 (75,0/15,0) Production date and Month in Japanese (eg: year+ 年+ month+ 月) : “ 20XX 年 XX月” Text, height 2,7 mm. Graphics, height 2,7 mm. According to 1234-3763, 1235-6102 and 1235-6103 Company Internal MARKING DRAWING 3 (5) Prepared (also subject responsible if other) No. SEM/CGOVDPLG, Anna Englund 1265-5198 Uen Approved Checked Date Rev Reference SEM/CGOVDPLG, Anna Englund 2012-04-20 1 Content Format Line C6 (79,0/15,0) Marking of origin. “Made in Xxx”; “Xxx” = actual country of production of the included telephone, in English Text, height 2,7 mm. Line D 1 (86,0/28,0) Model name, “SO-05D” Text, height 3,3 mm. According to Chapter 1 in MLCI. Line D 2 (90,0/23,5) Electronic serial number of the included telephone. “IMEI: 00000000-000000-0” Text, height 2 mm. Supplied by system. Line E 1 (98,8/2,5) Electronic serial number of the included telephone. "354012000693272” Font Zebra printer Scaleable Smooth Font Arial, font size 20 pt, text height 5,5 mm Space between fonts 0.6 mm. Clear area of left and right: 2.54mm Clear area of top and bottom: 2.4mm Text should be centred in vertical way and horizontal way. Line E 2 (115,0/7,0) Electronic serial number of the included telephone in bar code with number in text-en-clair; “*354012000693272*” Bar code, height 12.5 mm incl. text-en- clair (actual bar code height 8,0 mm). Font Zebra printer Scaleable Smooth Font Arial Narrow , Font size 13 pt, text height 3.0 mm. Code 39 symbology, code C subset. If uneven number of digits, code B subset shall be used for the last digit. Company Internal MARKING DRAWING 4 (5) Prepared (also subject responsible if other) No. SEM/CGOVDPLG, Anna Englund 1265-5198 Uen Approved Checked Date Rev Reference SEM/CGOVDPLG, Anna Englund 2012-04-20 1 1.3 Layout The conceptual picture (for Zebra 90XiII printer, or equivalent) should not be considered as specifications, but as an additional help for setting up the label. 1.3.1 Conceptual picture double underlined = changed since last revision. Company Internal MARKING DRAWING 5 (5) Prepared (also subject responsible if other) No. SEM/CGOVDPLG, Anna Englund 1265-5198 Uen Approved Checked Date Rev Reference SEM/CGOVDPLG, Anna Englund 2012-04-20 1 2 CE marking and F…

Text truncated - open the document above for the full version.

Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 23 of 30 An ne x C Inte r na l p ho to gra phs o f the E UT Photo documentation: Photo 1: Photo 2: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 24 of 30 Photo 3: Photo 4: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 25 of 30 Photo 5: Photo 6: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 26 of 30 Photo 7: Photo 8: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 27 of 30 Photo 9: Photo 10: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 28 of 30 Photo 11: Photo 12: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 29 of 30 An ne x D Doc u me n t his to r y Version Applied changes Date of release 1.0 Initial release 2012-11-02 -A Plot of a retest inserted (Page 10) 2012-11-02 An ne x E Fur the r in for ma ti o n Glossary AVG - Average DUT - Device under test EMC - Electromagnetic Compatibility EN - European Standard EUT - Equipment under test ETSI - European Telecommunications Standard Institute FCC - Federal Communication Commission FCC ID - Company Identifier at FCC HW - Hardware IC - Industry Canada Inv. No. - Inventory number N/A - Not applicable PP - Positive peak QP - Quasi peak S/N - Serial number SW - Software Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 30 of 30 An ne x F Ac c re di ta t ion Ce r t ific a te Front side of certificate Back side of certificate Note: The current certificate including annex is published on our website (see link below) or may be received from CETECOM ICT Services on request. http://www.cetecom.com/fileadmin/de/CETECOM_D_Saarbruecken/accreditations_Jan_2010/DAKKS_Akkredi_ Urk_EN17025-En_incl_Annex.pdf

2012-12-12 Page 1 of 30 TEST REPORT Test report no.: 1-4254/12-59-03-A Testing Laboratory Applicant CETECOM ICT Services GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken/Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom-ict.de e-mail: [email protected] Accredited Test Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-01 Area of Testing: Radio/Satellite Communications Sony Mobile Communications AB Nya Vattentornet 22188 Lund/SWEDEN Phone: +46 46 19 30 00 Fax: +46 46 19 32 95 Contact: Håkan Sjöberg e-mail: [email protected] Phone: +46 46 19 35 59 Manufacturer Sony Mobile Communications AB Nya Vattentornet 22188 Lund/SWEDEN Test Standard/s 47 CFR Part 15 Title 47 of the Code of Federal Regulations; Chapter I Part 15 - Radio frequency devices For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: GSM Mobile Phone GPRS/EGPRS 850/900/1800/1900; UMTS HSPA FDDI/V/VI/XIX; LTE FDD 1/19/21; WLAN a/b/g/n; BT 3.1; BT LE; RFID; FM Rx; GPS Model name: PM-0220-BV Frequency [MHz]: GSM: 824.2 – 848.8 MHz, 1850.2 – 1909.8 MHz UMTS: 826.4 – 846.6 MHz Technology tested: Receiver Antenna: Integrated antenna Power Supply: 3.7 V DC by Li - polymer battery Temperature Range: -20°C to +55 °C Test report authorised: Test performed: 2012-12-12 p.o. Stefan Bös 2012-12-12 Marco Bertolino Senior Testing Manager Testing Manager Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 2 of 30 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General Information ....................................................................................................................................... 3 2.1 Notes and disclaimer .......................................................................................................................... 3 2.2 Application details ............................................................................................................................... 3 3 Test standard/s ............................................................................................................................................... 3 4 Test Environment ........................................................................................................................................... 4 5 Test item .......................................................................................................................................................... 4 6 Test Laboratories sub-contracted ................................................................................................................ 4 7 Summary of Measurement Results .............................................................................................................. 5 7.1 Receiver ................................................................................................................................................ 5 8 Measurement Results .................................................................................................................................... 6 8.1 RX spurious emissions conducted < 30 MHz ................................................................................... 6 8.2 RX spurious emissions radiated ........................................................................................................ 8 9 Test equipment and ancillaries used for tests .......................................................................................... 13 10 Observations ......................................................................................................................................... 14 Annex A Photographs of the test setup ...................................................................................................... 15 Annex B External photographs of the EUT ................................................................................................. 20 Annex C Internal photographs of the EUT .................................................................................................. 23 Annex D Document history .......................................................................................................................... 29 Annex E Further information ........................................................................................................................ 29 Annex F Accreditation Certificate ............................................................................................................... 30 Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 3 of 30 2 General Information 2.1 Notes and disclaimer The test results of this test report relate exclusively to the test item specified in this test report. CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CETECOM ICT Services GmbH. The testing service provided by CETECOM ICT Services GmbH has been rendered under the current "General Terms and Conditions for CETECOM ICT Services GmbH". CETECOM ICT Services GmbH will not be liable for any loss or damage resulting from false, inaccurate, inappropriate or incomplete product information provided by the customer. Under no circumstances does the CETECOM ICT Services GmbH te…

Text truncated - open the document above for the full version.

Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 15 of 30 An ne x A P ho tog ra phs o f t h e te s t s e tu p Photo documentation: Photo 1: Photo 2: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 16 of 30 Photo 3: Photo 4: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 17 of 30 Photo 5: Photo 6: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 18 of 30 Photo 7: Photo 8: Test Report No.: Test report no.: 1-4254/12-59-03-A 2012-10-24 Page 19 of 30 Photo 9: