PY7PM-0620Multi-Band GSM/ EDGE/ LTE Phone with WLAN, Bluetooth, ANT+ and RFID

Startup guide Xperia ™ Z Ultra C6802/C6833/C6806/C6843 Sony Mobile Communications AB SE-221 88 Lund, Sweden www.sonymobile.com 1273-3172.1 Welcome Important Information Before you use your device, please read the Important Information provided in your device or in the box. Assembly To insert the memory card The memory card may not be included at purchase in all markets. To insert the SIM card 2 3 1 4 5 Inserting the micro SIM card into the device without the SIM card holder could damage your micro SIM card or your device, and Sony does not warrant and will not be responsible for any damage caused by such action. To view the CE mark and the FCC ID 1 2 333 1 Remove the cover for the memory card and micro SIM card slots. 2 Insert a fingernail, or a sharp object such as a pen, into the hole in the label tray, then drag the tray outwards to view the CE mark and the FCC ID. Protecting your device from water and dust <1.5m Swimming poolDivingSand/mud Salt waterOther liquid chemicals Your device has IP (Ingress Protection) ratings of IP5X, IPX5 and IPX8. These ratings mean that your device is dust resistant and is protected against low pressure water stream as well as against the effects of submersion for 30 minutes in fresh (non-saline) water up to 1.5 metres deep. Always firmly attach all covers to ensure the water and dust resistance of the device. If liquid is detected inside the device, for example, underneath one of the covers, your warranty will be void. If the speaker, microphone or headset jack get wet, dry these areas and wait for three hours before using them again. You can, however, use other features in the device that do not utilise the speaker or microphone. Before using your device in water and in dusty conditions, refer to the relevant section of the User guide for your device for more detailed information. An online User guide as well as a downloadable version is available at www.sonymobile.com/support. Basics Overview 12345 6 7 8 9 1112 10 13 14 15 16 1. Second microphone 2. Proximity sensor/Light sensor 3. Front camera lens 4. Ear speaker 5. Charging light/ Notification light 6. Headset jack 7. Micro SIM and memory card slot cover 8. Power key 9. Volume/Zoom key 10. Strap hole 11. Speaker 12. Main microphone 13. Main camera lens 14. Charger/USB cable port cover 15. NFC™ detection area 16. Charging dock connector Turning on the device To turn on the device Make sure that the battery is charged for at least 30 minutes before you turn on the device for the first time. 1 Press and hold down the power key until the device vibrates. 2 Wait a while for the device to start. Waking up the screen To activate the screen • Briefly press the power key . To unlock the screen • Swipe up or down on the lower part of the screen. Using the keys Back • Go back to the previous screen • Close the on-screen keypad, a dialog box, an options menu, or the Notification panel Home • Go to the Home screen Task • Tap to open a window showing your most recently used applications and a small apps bar Set up your device What is Android™? Android is your device's operating system. Since Android is developed by Google™, your device is preloaded with several Google™ services, such as Google Maps™ and Google™ web search. To use some of the services provided by Google™, you need a Google account. Google™ account With a Google™ account, you can use Gmail™ to send emails, Google Talk™ to chat with friends, and Google Play™ to download applications and games, music, movies and books. To set up a Google™ account on your device 1 From your Home screen, tap . 2 Find and tap Settings > Add account > Google. 3 Follow the registration wizard to create a Google™ account, or sign in if you already have an account. You can also sign in to or create a Google™ account from the setup guide the first time you start your device. Or you can go online and create an account at www.google.com/accounts. Basic settings The first time you start your device, a setup guide explains basic device functions and helps you enter essential settings. You can also access the setup guide later. To access the setup guide manually 1 From the Home screen, tap . 2 Tap Settings > Setup guide. Transferring contacts to your new device Transferring contacts to your new device can sometimes be complicated, but help is available. You can transfer contacts from several device brands, including iPhone, Samsung, HTC and Nokia. You need: • An Internet-connected PC or Apple® Mac® computer • A USB cable for your old device • A USB cable for your new Android™ device • Your old device and new Android™ device Get started transferring your contacts If you are a PC user, use the PC Companion program to transfer your contacts. It's free, and the installation files are already saved on your new device. PC Companion also offers a range of other features, including help to update your device software. For Apple® Mac® computer users, the Sony™ Bridge for Mac application is available to help you transfer your contacts. It's also free and downloadable from www.sonymobile.com/support. To install PC Companion 1 New device: Turn on your new Android™ device and connect it to a PC using a USB cable. 2 New device: Tap Install to install PC Companion on the PC. 3 Computer: If a popup window appears to notify you about available PC software, select Run Startme.exe. 4 Computer: Click Install to start the installation and then follow the instructions to complete the installation. To transfer contacts to your new device using PC Companion 1 Make sure that PC Companion is installed on your PC. 2 Open the PC Companion program on the PC, then click Contacts Setup and follow the instructions to transfer your contacts. To install Sony™ Bridge for Mac 1 Using your Apple Mac computer, go to www.sonymobile.com/support, then search for and download the Sony™ Bridge for Mac application to a folder on the computer. 2 After the download is complete, open the folder and double-click the Sony Bridg…

Text truncated - open the document above for the full version.

Sony Mobile Communications Confidential LETTER 1(1) Document number Revision 227/0061-LXE 110 0790 Uen A Prepared by Date SEM/CGQTAD RAZVAN BUJILA 2013-07-25 Contents responsible if other than preparer Remarks This document is managed in metaDoc. Approved by SEM/CGQTAD (RAZVAN BUJILA) It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Telecommunication Certification Body PCTEST Engineering Laboratory Inc. 6660-B Dobbin Road Columbia MD 21045 USA To whom it may concern This is to certify that Sony Mobile Communications AB authorizes PCTEST to act as Telecommunication Certification Body on our behalf for the FCC application of our mobile phone C6843, FCC ID: PY7PM-0620. We certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Yours sincerely Razvan Bujila Global Type Approval Sony Mobile Communications Tel: +46 10 801 53 23 Mobilvägen 10, SE-221 88 Lund, Sweden [email protected]

Sony Mobile Communications Confidential LETTER 1(1) Document number Revision 228/0061-LXE 110 0790 Uen A Prepared by Date SEM/CGQTAD RAZVAN BUJILA 2013-07-25 Contents responsible if other than preparer Remarks This document is managed in metaDoc. Approved by SEM/CGQTAD (RAZVAN BUJILA) It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Telecommunication Certification Body PCTEST Engineering Laboratory Inc. 6660-B Dobbin Road Columbia MD 21045 USA Subject: Certification Application FCC ID: PY7PM-0620 It is requested that the following information is to be held confidential on behalf of Sony Mobile Communications AB pursuant to FCC Rules Parts 0.457 and 0.459: Block Diagrams Schematics Parts List Tune Up Information Operation Description These items contain detailed system and equipment description and related information about the product which Sony Mobile Communications AB considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Mobile Communications AB also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Yours sincerely Razvan Bujila Global Type Approval Sony Mobile Communications Tel: +46 10 801 53 23 Mobilvägen 10, SE-221 88 Lund, Sweden [email protected]

SONY MOBILE FCC ID: PY7PM-0620 External Photos EUT Type: Portable Handset Page 1 of 3 © 2013 PCTEST Engineering Laboratory Inc. EXTERNAL PHOTOGRAPHS SONY MOBILE FCC ID: PY7PM-0620 External Photos EUT Type: Portable Handset Page 2 of 3 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 External Photos EUT Type: Portable Handset Page 3 of 3 © 2013 PCTEST Engineering Laboratory Inc.

Prepared by SHIGERU, IWASAKI Contents responsible if other than preparer Approved by TAKEFUMI, MASUDA the responsibility of the user to ensure that they have a correct and valid Applies to FCC ID: PY7PM- Marking Drawing The FCC ID is placed on a none removable label tray according to below picture Confidential PROJECT REPORT Document number SEM/CVGAERB GAVIN HAN Date SEM/CVGAERB GAVIN HAN Remarks This document is managed in metaDoc. the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. -0620 Marking Drawing - PY7PM-0620 The FCC ID is placed on a none removable label tray according to below picture 1(1) Revision HAN9/0362-1/FCP 119 A HAN This document is managed in metaDoc. version. Any outdated hard copy is invalid and must be removed from possible use. The FCC ID is placed on a none removable label tray according to below picture

SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 1 of 8 © 2013 PCTEST Engineering Laboratory Inc. INTERNAL PHOTOGRAPHS SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 2 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 3 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 4 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 5 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 6 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 7 of 8 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Internal Photos EUT Type: Portable Handset Page 8 of 8 © 2013 PCTEST Engineering Laboratory Inc.

FCC ID: PY7PM-0620 FCC Pt. 15.225 MEASUREMENT REPORT (CERTIFICATION) Reviewed by: Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 1 of 21 0Y1307231392.PY7 04/30 - 05/09/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 3.1RFFI 09/25/2012 Applicant Name: Date of Testing: Sony Mobile Communications 04/30 - 05/09/2013 Nya Vattentornet Test Site/Location: SE-221 88, Lund PCTEST Lab, Columbia, MD, USA Sweden Test Report Serial No.: 0Y1307231392.PY7 FCC ID: PY7PM-0620 APPLICANT: Sony Mobile Communications Application Type: Certification Type Number: PM-0620-BV EUT Type: Portable Handset Frequency: 13.56MHz FCC Classification: Low Power Communications Device Transmitter (DXX) FCC Rule Part(s): FCC Part 15 Subpart C (15.225) IC Specification(s): RSS-210 Issue 8 Test Procedure(s): ANSI C63.10-2009 The device bearing the FCC Identifier specified above has been shown to comply with the applicable technical standards as indicated in the measurement report and has been tested in accordance with the measurement procedures specified in ANSI C63.10-2009 (See Test Report). These measurements were performed with no deviation from the standards. Test results reported herein relate only to the item(s) tested. I authorize and attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. NVLAP accreditation does not constitute any product endorsement by NVLAP or any agency of the United States Government. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 15.225 / IC RSS-210 NFC FCC ID: PY7PM-0620 FCC Pt. 15.225 MEASUREMENT REPORT (CERTIFICATION) Reviewed by: Quality Manager Test Report S/N: Test Date(s): EUT Type: Page 2 of 21 0Y1307231392.PY7 04/30 - 05/09/2013 Portable Handset © 2013 PCTEST Engineering Laboratory, Inc. REV 3.1RFFI 09/25/2012 TABLE OF CONTENTS FCC Part 15.225 MEASUREMENT REPORT ............................................................................................. 3 1.0 INTRODUCTION .............................................................................................................................. 4 1.1 SCOPE .................................................................................................................................................. 4 1.2 PCTEST TEST LOCATION ................................................................................................................... 4 2.0 PRODUCT INFORMATION .............................................................................................................. 5 2.1 EQUIPMENT DESCRIPTION ................................................................................................................ 5 2.2 DEVICE CAPABILITIES ........................................................................................................................ 5 2.3 TEST CONFIGURATION ...................................................................................................................... 5 2.4 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS ............................................................................. 5 2.5 LABELING REQUIREMENTS ............................................................................................................... 5 3.0 DESCRIPTION OF TEST ................................................................................................................. 6 3.1 EVALUATION PROCEDURE ................................................................................................................ 6 3.2 AC LINE CONDUCTED EMISSIONS .................................................................................................... 6 3.3 RADIATED EMISSIONS ........................................................................................................................ 7 4.0 ANTENNA REQUIREMENTS .......................................................................................................... 8 5.0 SAMPLE CALCULATIONS .............................................................................................................. 9 5.1 CONDUCTED EMISSION MEASUREMENT SAMPLE CALCULATION ............................................... 9 5.2 RADIATED EMISSION MEASUREMENT SAMPLE CALCULATION .................................................... 9 6.0 TEST EQUIPMENT CALIBRATION DATA .................................................................................... 10 7.0 ENVIRONMENTAL CONDITIONS ................................................................................................. 11 8.0 TEST DATA .................................................................................................................................... 12 8.1 SUMMARY .......................................................................................................................................... 12 8.2 20DB BANDWIDTH MEASUREMENT ................................................................................................ 13 8.3 FREQUENCY STABILITY TEST DATA ............................................................................................... 14 8.4 IN-BAND RADIATED SPURIOUS EMISSION MEASUREMENTS ...................................................... 16 8.5 RADIATED SPURIOUS EMISSION MEASUREMENTS, OUT-OF-BAND .......................................... 17 8.6 LINE CONDUCTED MEASUREMENT DATA ..................................................................................... 19 9.0 CONCLUSION ....................................…

Text truncated - open the document above for the full version.

SONY MOBILE FCC ID: PY7PM-0620 Test Set-Up Photos EUT Type: Portable Handset Page 1 of 3 © 2013 PCTEST Engineering Laboratory Inc. TEST SETUP PHOTOGRAPHS SONY MOBILE FCC ID: PY7PM-0620 Test Set-Up Photos EUT Type: Portable Handset Page 2 of 3 © 2013 PCTEST Engineering Laboratory Inc. SONY MOBILE FCC ID: PY7PM-0620 Test Set-Up Photos EUT Type: Portable Handset Page 3 of 3 © 2013 PCTEST Engineering Laboratory Inc.