Q2RSA-W989NFC waterproof bluetooth speaker

HONGKONG TRANSWIN DEVELOPMENT LTD NFC waterproof bluetooth speaker User Manual — (SA-W989) Size: 181*Ф67mm 1. Description of functions 1.1 Type: Outdoor waterproof speaker with LED light. 1.2 Micro USB cable for charging 1.3 Power supply mode: Built‐in 5V 2200mAh Li ‐Ion battery charged by micro USB cable. 1.4 Speaker unit specifications: 5 Watt*2, 45mm circumference. 1.5 Audio source: any device with a compatible 3.5mm audio output socket, notebooks, PCs, iPad, iPhone, iPod, mobile phones, smartphones, and many other devices (see Diagram 3 below for input port ). 1.6 Micro phone function: While your phone is connected with our bluetooth speaker, if any incoming calls, When the calls come in, there is a beep to notify you ,please just press the play/Pause button shortly for answering the call.. Please pay attention to the position on the silicone that the microphone located. 1.7 Bluetooth connecting: Short press the button, after you hear” hello” till “start pairing”, it means come to the pairing mode, while the Blue LED light is twinkled quickly, you can use you Bluetooth to search the speaker, it’s pairing name is “SA‐W989”, once the speaker is connected with Bluetooth device, the notification will be ”paired” the LED light will stop twinkled , after you play music, the LED light will twinkled regularly and slowly. With long press the button ,the speaker will turn off and the notification will be ”Goodbye”. If there is no device to be paired with the speaker, then the speaker will turn off automaticly 5 minutes later.When the speaker is in bluetooth mode,the audio cable can be worked to control the speaker to be play/pause ,through put into/out. 1.8 If your bluetooth device was connected with the speaker before, you just need press button for one second/short press, and let it go then you will hear the notification” hello, start pairing ,paired” in 2 seconds, it means the speaker has paired with your Bluetooth speaker automatically, but your Bluetooth device should be working at the same time. If your Bluetooth device is closed, after you open the Bluetooth device, the speaker will search for the device automatically in one second. 1.9 Bluetooth Disconnect: When the Bluetooth is in the mode of disconnected, the notification will be “not connection” If you disconnect your Bluetooth device with the speaker, the LED light will start twinkling quickly, it means the speaker is in the pairing mode. If there is no device to be paired with the speaker; If you disconnect your phone and speaker, but forget to close our Bluetooth speaker, it will turn off automaticly 5 minutes later. If your phone is connected with the speaker, while you have a call comes in, and you answering the call, you leave away from the speaker, since the distance will cause the speaker and your phone disconnected, you will hear the notification ”not connection” from our speaker, So we suggest you need to answer the call closed to the Bluetooth speaker. Another situation, if your audio device is taken away from our bluetooth speaker while it is connected, it will be disconnected since the distance between them, you also can hear ”not connection”. once you close to the speaker it will connect with the speaker automatically and voice out ”paired”. Then you can play your music again. 2.0 NFC operations: Please check the NFC mark on the silicone cover, near Field communication, is as set of standard for smartphone and this speaker to establish Bluetooth radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. You should always pay attention to your phone’s screen to focus on the steps to finish the connecting with our bluetooth speaker. ‐You can pair up the device by NFC triggering. ‐Make sure your music device or mobile phone do have the NFC function. Please refer to your music device or mobile phone instruction manual for detail. ‐ Make sure the NFC function and S Beam function are both enabled at your music device or mobile phone. Please refer to your music device or mobile phone instructional manual for detail. ‐Switch on our Bluetooth speaker. ‐Place the music device or mobile phone on our bluetooth speaker where the NFC located. The music device or mobile phone will prompt a new Bluetooth device is found and would you like to pair it up. Pick up the music device or the mobile phone(You are strongly suggested to pick up the music device before accepting to pairing up in order to reduce the signal interference).Now you can press on the music device or mobile phone to accept pairing up with the founded bluetooth device. Once the device is connected with our bluetooth speaker, it will voice out “paired” Repeat the above process again to unpair our bluetooth speaker. Important: For some smartphones, please active the NFC function(subjects to phone’s own setting)and Bluetooth function of your smartphone at the same time. （NFC Only receiver function） 2.1 Button function: The speaker with the function likes volume control, songs tracking, play/pause ect, handsfree, all the functions will be come ture by operating the buttons on the silicone cover. 2.1.1 ON/OFF button on the speaker, (see Diagram 1 below). 2.1.2 VOL‐/BWD button function (see Diagram 1 below): Long press the button is control the volume“‐“ (VOL‐/FWD) ,short press the button is for the songs backward and forward. 2.1.3 VOL+/FWD button function (see Diagram 1 below): To increase volume press “+” (VOL+/FWD) button and hold, to go to next song press the button shortly. 2.1.4 PLAY/PAUSE button function(see Diagram 1 below): When playing music, the Play/Pause can control playing the audio source, short press Play/Pause button to pause or play music. 2.2 Micro USB Charging/Aux‐in port: These ports are on the top of the unit, You can charge the built‐in Li ‐Ion battery via the micro USB port, you can see Red LED light will be lighten up. If you connect your device and the speaker via the a…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 Dongguan ShengYu Electronic Technology Co., Ltd July 31, 2015 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Dongguan ShengYu Electronic Technology Co., Ltd hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product name: NFC waterproof bluetooth speaker Model No.: SA-W989, 8037281 FCC ID: Q2RSA-W989 Sincerely, Client’s signature: Client’s name / title: Andy Liu / Deputy General Manager Contact information / address: NO.180 KangYi Road. ChangShanTou Village. QingXi Town. DongGuan, GuangDong, 523657, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (current) 3.0 4.0 March-26-2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 4.0 Dongguan ShengYu Electronic Technology Co., Ltd July 31, 2015 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: Q2RSA-W989 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: Andy Liu / Deputy General Manager Contact information / address: NO.180 KangYi Road. ChangShanTou Village. QingXi Town. DongGuan, GuangDong, 523657, China

Dongguan ShengYu Electronic Technology Co., Ltd Date: July 31, 2015 To SIEMIC Inc 775 Montague Expressway Milpitas, CA 95035 Statement Model number: SA-W989, 8037281 FCC ID: Q2RSA-W989 We hereby state that these models are identical in interior structure, electrical circuits and components, and just model names are different for the marketing requirement. Your assistance on this matter is highly appreciated. Sincerely, Client’s signature: Client’s name / title: Andy Liu / Deputy General Manager Contact information / address: NO.180 KangYi Road. ChangShanTou Village. QingXi Town. DongGuan, GuangDong, 523657, China

Label and label location Dongguan ShengYu Electronic Technology Co., Ltd NFC waterproof bluetooth speaker Model No.: 8037281 FCC ID: Q2RSA-W989 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Dongguan ShengYu Electronic Technology Co., Ltd NFC waterproof bluetooth speaker Model No.: SA-W989 FCC ID: Q2RSA-W989 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Antenna

FCC ID : Q2RSA-W989 1. RF EXPOSURE 1.1. The Requirement System operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See Section 15.247(b)(4) and Section 1.1307(b)(1) 1.2. Limit For Maximum Permissible Exposure (MPE) Limits for General Population/ Uncontrolled Exposure F = frequency in MHz, * Plane-wave equivalent power density 1.3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) ( 2 mW/cm) Averaging Time 2 E, 2 H or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 f/1500 30 1500-100,000 1.0 30 From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the antenna is 0 dBi, the RF power density can be obtained. 1.4. TEST RESULTS Maximum measured transmitter power Test Frequency （MHz） Minimum Separation Distance (cm) Output Power (dBm) Output Power (mW) Target power (dBm) Antenna Gain (Numeric) Power Density Limit (mW/cm 2 ) Power Density At 20 cm (mW/cm 2 ) Test Results 2402 20.00 -7.59 0.174 -8 ±1 1. 000 1.000 0.004 Pass 2440 20.00 -7.58 0.175 -8 ±1 1. 000 1.000 0.004 Pass 2480 20.00 -7.63 0.173 -8 ±1 1. 000 1.000 0.004 Pass The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure. 1.5. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches) during normal operation. Proposed RF exposure safety information to include in User’s Manual.

Report No.: ATE20151555 Page 1 of 58 FCC ID: Q2RSA-W989 ACCURATE TECHNOLOGY CO., LTD APPLICATION CERTIFICATION FCC Part 15C On Behalf of Dongguan ShengYu Electronic Technology Co., Ltd NFC waterproof bluetooth speaker Model No.: SA-W989, 8037281 FCC ID: Q2RSA-W989 Prepared for : Dongguan ShengYu Electronic Technology Co., Ltd Address : NO.180 KangYi Road. ChangShanTou Village. QingXi Town. DongGuan, GuangDong, 523657, China Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Chan Yuan New Material Port, Keyuan Rd. Science & Industry Park, Nan Shan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report No. : ATE20151555 Date of Test : July 21-23, 2015 Date of Report : July 30, 2015 Report No.: ATE20151555 Page 2 of 58 FCC ID: Q2RSA-W989 ACCURATE TECHNOLOGY CO., LTD TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 5 1.1. Description of Device (EUT)....................................................................................................................5 1.2. Carrier Frequency of Channels .................................................................................................................6 1.3. Special Accessory and Auxiliary Equipment ...........................................................................................6 1.4. Description of Test Facility ......................................................................................................................7 1.5. Measurement Uncertainty.........................................................................................................................7 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 8 3. OPERATION OF EUT DURING TESTING ................................................................................. 9 3.1. Operating Mode ........................................................................................................................................9 3.2. Configuration and peripherals ..................................................................................................................9 4. TEST PROCEDURES AND RESULTS ....................................................................................... 10 5. POWER LINE CONDUCTED MEASUREMENT ..................................................................... 11 5.1. Block Diagram of Test Setup..................................................................................................................11 5.2. Power Line Conducted Emission Measurement Limits..........................................................................11 5.3. Configuration of EUT on Measurement .................................................................................................11 5.4. Operating Condition of EUT ..................................................................................................................11 5.5. Test Procedure ........................................................................................................................................12 5.6. Power Line Conducted Emission Measurement Results ........................................................................13 6. 6DB BANDWIDTH MEASUREMENT ........................................................................................ 19 6.1. Block Diagram of Test Setup..................................................................................................................19 6.2. The Requirement For Section 15.247(a)(2) ............................................................................................19 6.3. EUT Configuration on Measurement .....................................................................................................19 6.4. Operating Condition of EUT ..................................................................................................................19 6.5. Test Procedure ........................................................................................................................................19 6.6. Test Result ..............................................................................................................................................20 7. MAXIMUM PEAK OUTPUT POWER ....................................................................................... 22 7.1. Block Diagram of Test Setup..................................................................................................................22 7.2. The Requirement For Section 15.247(b)(3)............................................................................................22 7.3. EUT Configuration on Measurement .....................................................................................................22 7.4. Operating Condition of EUT ..................................................................................................................22 7.5. Test Procedure ........................................................................................................................................22 7.6. Test Result ..............................................................................................................................................23 8. POWER SPECTRAL DENSITY MEASUREMENT.................................................................. 25 8.1. Block Diagram of Test Setup..................................................................................................................25 8.2. The Requirement For Section 15.247(e).................................................................................................25 8.3. EUT Configuration on Measurement .....................................................................................................25 8.4. Operating Condition of EUT ...…

Text truncated - open the document above for the full version.

Test Photos