Q5Q-WSEchometer Wireless Sensor

Wireless Sensor User Guide Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 Scope: This manual pertains to the products listed in Table 1 below. Associated FCC and IC identification numbers are listed, as well as page number for the specific sensor’s installation instructions. Table 2 includes the FCC Label design and intended installation location. Sensor Model # : Description FCC ID IC ID WPRT: Wireless Polished Rod Transducer Q5Q-WS 10048A-WS WHT: Wireless Horseshoe Transducer WHT50K: Wireless Horseshoe Transducer - 50,000 pounds WPT: Wireless Pressure Transducer WGDA: Wireless General Data Acquisition Table 1 All of the above utilize the same electronic PCB, Antenna, Battery, and run the same Firmware. The PCB in each case is packaged in a fully enclosed stainless steel enclosure. Each model includes a different transducer element wired to the PCB (such as a strain gauge, or thermistor). The instructions and pictures below depict the WPRT model. All other models will be similar except for differences in the physical form factor. Table 2 The Wireless Sensors are components of the Echometer Well Analyzer and designed to be used with the Echometer WB100 Wireless Base, providing a wireless option for obtaining data, (such as dynamometer, power and pressure/temperature). The data is analyzed by the Wireless Sensor User Guide Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 Echometer TAM software which runs on a PC/Notebook and utilized to provide analysis of well performance. Please refer to the Echometer TAM Software User Manual for instructions specific to software operation and to the Echometer WB100 Wireless Base User Manual for instructions specific to that device. • WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s expense. • This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the antenna and your body. • This Class A digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada) • This device has been designed to operate with the antennas listed below. The specific models listed or substitutes as specified below may be used. o Pulse W1030 o Linx Tech ANT-2.4-CW-RAH-RPS: 2.4GHz o Substitutes may be used, as long as they meet the 2.4GHz, 50Ω, <=2dBi gain, RPSMA Male requirements. Wireless Sensor User Guide Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 WPRT Installation: 1. Clamp the Wireless Polished Rod Transducer (WPRT) to the polished rod on the oil well below the carrier bar. 2. Install the antenna as shown. It is desirable that the antenna be pointed upwards during operation. 3. Press the Power button on the WPRT as indicated below: a. The LED above the Power button will proceed with the LED test, (illuminating three green, and then three red LEDs). b. Following the LED test, the Power button LED will flash a maximum of ten times in rapid succession to indicate battery power. A fully charged battery will flash ten times, with fewer flashes as the battery charge drops. Recharge the battery when the flashes reduce to two. c. Following the battery test, the Power LED will flash once per second to indicate the WPRT is ready to proceed. 4. Press the Install button as shown below: a. The Install LED will flash RED if the WPRT it too tight or flash GREEN if it is too loose. Tighten or loosen the knob as needed until the LED illuminates solid green. Wireless Sensor User Guide Echometer Company 5001 Ditto Lane Wichita Falls, TX 76302 24 Sep 2012 5. Press the Acquire button as shown below to initiate data acquisition. Use the TAM software and instructions to complete the test. Pressing ACQUIRE again will stop acquisition. 6. To turn off the WPRT, simply press the Power button for two seconds.

ID LABEL Wireless General Data Acquisition Detail Page 2 Wireless Horseshoe Transducer

ID LABEL Wireless General Data Acquisition Wireless General Data Acquisition Detail Page 2 Wireless Horseshoe Transducer Wireless Horseshoe Transducer 2.1in Diameter Detail Page 2 Wireless Horseshoe Transducer50K lbs 2.1in Diameter 3.200 1.905 R.100 .025 5 4 3 2 1 DRAWN BY: MATERIAL Plastic w/ Adhesive DATE INITIALS Echometer Company TITLE: SIZE A DWG. NO. REVISION: 0 SCALE: 1:1 UNLESS OTHERWISE SPECIFIED: DO NOT SCALE DRAWING DIMENSIONS ARE IN INCHES TOLERANCES: FRAC. 1/32 .XX .01 .XXX .005 .XXXX .0005 ANG. .5 JBW 08-24-2012 SHEET 1 OF 1 PRT-0700-001 Seal Label PROPRIETARY AND CONFIDENTIAL: THE INFORMATION CONTAINED IN THIS DRAWING WAS GENERATED ON BEHALF OF JERRY WEST, LLC CLIENT, Echometer Company. THIS DRAWING IS THE SOLE PROPERTY OF Echometer Company. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Echometer Company IS PROHIBITED. FINISH None CLIENT: (((ECHOMETER))) MODEL WPRT ECHOMETER COMPANY Wichita Falls, TX www.echometer .c om WIRELESS POLISH ROD TRANSDUCER FCC ID:Q5Q-WS IC:10048A-WS This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer ence, and (2) this device must accept any interfer ence recieved, including interfer ence that may cause undesired operation. Label Detail Page 2 Wireless Pressure Transducer MODEL WPT Wireless Pressure Transducer 2.1in Diameter

TenX Precision, LLC. Confidential 25 09 May 2011 TenX Precision, LLC. Confidential 25 09 May 2011 TenX Precision, LLC. Confidential 25 22 Feb 2011 Echometer Wireless Sensor Actual Size: 1.3 x 2.5 in Antenna SensorsChargerBatteryAccelerometer

1. ANT-2.4-CW-RAH-xxx Radiation Patterns (at Edge of Jig #50-V2) 2. Chamber

Wireless External Antenna for 2.4 GHz Applications Pulse Part Number: W1030 © 2007 All Rights Reserved. W1030 Datasheet Version 1.1. September 2007 Feat ures - Shortest antennas in product lin e - For WLAN devices using WiFi (802.11b/g), Bluetooth® and ZigBee TM - Omni-directional radiation patte rn provides broad 360° coverage - One-quarter wavelength dipole confi guratio n - Connection options easily integrate with OEM designs Connector Option s - Reverse SMA (Male)* - SMA (Male) * Default Configuration – Please contact Pulse Applications Engineering for assistance in ordering connectors Weight........................................................6.3 grams Carton...........................................20/bag; 500/carton Dimensions: Inches mm Unless otherwise specified, a ll to lerances are ± .010 0.25 Frequency [GHz] VSWR Length Impedance [Nom] ≤ 2. 01/4, dipole50 Ω Electrical Specifications @ 25 ºC Note: This par t number is lead- free and RoHS compliant. N o additional suffix or identifier is required. Gain [dBi] 2.0 Radiatio n Omni Polarization Vertic al Antenna Part No. W1030 Pulse Antennas Takatie 6 90440 K empele Finland Tel: +358 207 935 500 www.pulseeng.com/antennas Exte rnal Antennas Sal es Contacts USA858 674 8100 UK44 1483 401 700 France33 3 84 35 04 04 Singapore65 6287 8998 Shanghai86 21 32181071 China86 769 5538070 Taiwan886 2 26980228 Electrical Wireless External Antenna for 2.4 GHz Applications Pulse Part Number: W1030 © 2007 All Rights Reserved. W1030 Datasheet Version 1.1. September 2007 Vertical Posi tion Horizontal Posi tion Gain Performance W1030 Omni-directional antennas provide a uniform, donut- shaped, 360° radiation pattern. The omni-directional pattern is suitable for point-to-multipoint broadcasting in all directions. This antenna is primarily used for WLAN applications. However, it can also be used for a variety of other applications within the specified frequency range. When used as an access point, th e antenna is ideally located at the center of the coverage ar ea. Application Notes Pulse Antennas Takatie 6 90440 K empele Finland Tel: +358 207 935 500 www.pulseeng.com/antennas Exte rnal Antennas Sales Contacts USA858 674 8100 UK44 1483 401 700 France33 3 84 35 04 04 Singapore65 6287 8998 Shanghai86 21 32181071 China86 769 5538070 Taiwan886 2 26980228

§ 15.247(i) Maximum Permissible Exposure RF Exposure Requirements: §1.1307(b)(1) and §1.1307(b)(2): Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. RF Radiation Exposure Limit: §1.1310: As specified in this section, the Maximum Permissible Exposure (MPE) Limit shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Sec. 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Sec. 2.1093 of this chapter. MPE Limit Calculation: EUT’s operating frequencies @ 2405-2480 MHz; highest conducted power = 4.68 dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 2 dBi. Equation from page 18 of OET 65, Edition 97-01 S = PG / 4R 2 or R = √PG / 4S where, S = Power Density (1 mW/cm 2 ) P = Power Input to antenna (2.94 mW) G = Antenna Gain (1.58 numeric) S = (2.94*1.58/ 4*3.14*20^2) = 0.001 mW/cm2 So the exposure limit is met at 20 cm.

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE ! BALTIMORE, MARYLAND 21230-3432 ! PHONE (410) 354-3300 ! FAX (410) 354-3313 33439 WESTERN AVENUE ● UNION CITY, CALIFORNIA 94587 ● PHONE (510) 489-6300 ● FAX (510) 489-6372 3162 BELICK STREET ● SANTA CLARA, CALIFORNIA 95054 ● PHONE (408 748-3585 ● FAX (510) 489-6372 The Nation’s First Licensed Nationally Recognized Testing Laboratory September 28, 2012 TenX Precision, LLC 11824 Jollyville Road, Suite 102 Austin, Texas 78759 Dear Daraius Hathiram, Enclosed is the EMC Wireless test report for compliance testing of the TenX Precision, LLC, Echometer Wireless Sensor as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), Part 15, Subpart B, ICES-003, Issue 4 February 2004 for a Class A Digital Device and FCC Part 15 Subpart C, RSS-210, Issue 8, Dec. 2010 for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\TenX Precision, LLC\EMCA33149B-FCC247 Rev. 1) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. Electromagnetic Compatibility TenX Precision, LLC Cover Page Echometer Wireless Sensor CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCA33149B-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page ii of viii DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the TenX Precision, LLC Echometer Wireless Sensor Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class A Digital Devices & 15.247 Subpart C & RSS-210, Issue 8, Dec. 2010 for Intentional Radiators MET Report: EMCA33149B-FCC247 Rev. 1 September 28, 2012 Prepared For: TenX Precision, LLC 11824 Jollyville Road, Suite 102 Austin, Texas 78759 Prepared By: MET Laboratories, Inc. 914 W. Patapsco Ave. Baltimore, MD 21230 Electromagnetic Compatibility TenX Precision, LLC Cover Page Echometer Wireless Sensor CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCA33149B-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page iii of viii DOC-EMC702 6/18/2009 Electromagnetic Compatibility Criteria Test Report for the TenX Precision, LLC Echometer Wireless Sensor Tested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class A Digital Devices & 15.247 Subpart C & RSS-210, Issue 8, Dec. 2010 for Intentional Radiators Dusmantha Tennakoon Jennifer Warnell Project Engineer, Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of the FCC Rules Parts 15B, 15.247 and Industry Canada standards ICES-003, Issue 4 February 2004, RSS-210, Issue 8, Dec. 2010 under normal use and maintenance. Shawn McMillen, Wireless Manager, Electromagnetic Compatibility Lab Electromagnetic Compatibility TenX Precision, LLC Report Status Echometer Wireless Sensor CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCA33149B-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page iv of viii DOC-EMC702 6/18/2009 Draft Status Sheet Draft Revision Draft Date Reason for Draft Revision  December 19, 2011 Initial Draft Issue. 1 September 28, 2012 Revised MPE per engineer corrections. Electromagnetic Compatibility TenX Precision, LLC Table of Contents Echometer Wireless Sensor CFR Title 47, Part 15B, 15.247; RSS-210, Issue 8, Dec. 2010 & ICES-003 MET Report: EMCA33149B-FCC247 Rev. 1 © 2012, MET Laboratories, Inc. Page v of viii DOC-EMC702 6/18/2009 Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ...................................................................................................................................................2 B. Executive Summary ............................................................................................................................................2 II. Equipment Configuration .......................................................................................................................................3 A. Overview .............................................................................................................................................................4 B. References ...........................................................................................................................................................5 C. Test Site ..............................................................................................................................................................5 D. Description of Test Sample .................................................................................................................................6 E. Equipment Configuration ....................................................................................................................................6 F. Support Equipment .............................................................................................................................................6 G. Ports and Cabling Information ........…

Text truncated - open the document above for the full version.

Photograph 1. Radiated Emission, Test Setup Photograph 2. Radiated Spurious Emissions, Test Setup, Below 1 GHz Photograph 3. Radiated Spurious Emissions, Test Setup, 1 GHz – 18 GHz Photograph 4. Radiated Spurious Emissions, Test Setup, 18 GHz – 26 GHz