Q92-BH-20E1Remote Control Transmitter

Remote Control Outlet - Please pay attention to the warning signs. - Read the instructions with caution before operating and keep it properly. 2 1. For indoor use only. Avoid high humidity, high temperature, and high magnetic field. 2. Do not connect any devices that may exceed the performance limits of the outlet. 3. Do not insert needles or any other metal objects into main outlets. 4. Do not disassemble or repair the product, but only by authorized service personnel. 5. Children are not allowed to use remote outlets without adult supervision. 6. To prevent children from suffocation and chocking, keep them away from packing materials. 7. Used batteries should be disposed of safely and in accordance with environmental protection standards. ReceiverTransmitter General Guidelines: 1. Plug the receiver into a powered outlet. 2. Remove the isolation tab in the battery compartment of the transmitter. 3. Press each ON/OFF button on the transmitter will turn on or off the corresponding receiver accordingly. To remove a receiver from all transmitter paring (no remote transmitter can control it): 1. Unplug the connected device from the receiver. 2. Unplug the receiver from the powered outlet. 3. Press and hold the program button on the receiver. 4. Plug the receiver back to the powered outlet while continuing to press program button for approximately 5 seconds until the indicator begins to flash. 5. Program reset is successful when the indicator on receiver flashes several times and stops blinking. 3 Note: 1. Program button of each receiver can also be used as a manual switch. 2. The receiver will remain “OFF” after a power cut to save energy. The receivers and transmitter have been pre-paired for immediate use, but there are few units may not be pre-programmed or programmed incorrectly, or you want to customize the configuration to meet your needs. To program a transmitter and receiver, please follow the steps below: 1. Cancel the programming referring to the above “Canceling Programming” section firstly. 2. Press the program button on the receiver until indicator light starts to blink. 3. Release the program button, press “ON” and then “OFF” button for any desired number on the transmitter. 4. Programming/paring is successful when the indicator light stops blinking. 4 If you find the receiver works abnormally or the indicator on the remote transmitter becomes dim, please replace the remote battery with a new DC 12V (type 23A ) battery, making sure the polarity +/- of the battery is correct. - Low battery power may decrease readable wireless remote range. - Remove batteries if the remote is not in use for an extended period of time. In the case that one receiver is unresponsive to a remote control, follow the steps below to resolve the issue: 1. If the receiver is unresponsive to the remote control, please refer to the “Canceling Programming” and “Programming the Receiver” sections in the manual to reset the receiver. 2. “Canceling Programming” is always prior to “Programming the Receiver” when you want to make some changes. 3. Make sure the receiver and appliance are properly connected and powered on. 4. May be the transmitter is too far away to control the receiver. 5. The wireless range may be shorted by other electronic devices, appliances, walls, and other physical barriers. - Input Voltage: 120VAC, 60Hz - Max Power Rating: 15A,1875W - Transmission Frequency: 433.92 MHz - Remote Control Range : 100 Feet (Free Area) - Remote Battery: 23A, 12V 5 Federal Communications Commission lnterference Statement. This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Redirect or relocate the receiving antenna. - |ncrease distance between the equipment and the receiver. - Connect the equipment into an outlet on a cIrcuit different from that to which the receiver is connected. - ConsuIt the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radio Frequency Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

CFR 47 §2.911(d)(5)(i) Attestation Letter Applicant: Address: Email: [email protected] Tel: Tel: +86 574-63265968 Attestation Letter Date: 2025-11-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i) Filing FCC ID: Q92-BH-20E1 NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. certifies that the equipment for which authorization is sought,is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature Jason Wang/Manager NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD.

CFR 47 §2.911 (d)(5)(ii) Attestation Letter Applicant: Address: Email: [email protected] Tel: Tel: +86574-63265968 Attestation Letter Date: 2025-11-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(ii) Filing FCC ID: Q92-BH-20E1 NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. certifies that as of the date of the filing of the application, the applicantis not identified on the Covered List as an entity producing “covered” equipment. And our product does not use Kaspersky software information. Sincerely, Signature Jason Wang/Manager NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD.

U.S. AGENT LETTER OF ATTESTATION Date: 2025-11-26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: Q92-BH-20E1 NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD., certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: Add: FRN: 0022061477 Tel: Tel: +86 574-63265968 Email: [email protected] Signed by (printed name): Jason Wang Signature: NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD.

Applicant:, Address: Email: [email protected] Tel: +86 574-63265968 QA-FR-170-B7/29/2014 FCC Authorization Date: 2025-11-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We,NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD., the undersigned, hereby authorizes Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out byShenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Jason Wang/Manager NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD.

Applicant: Address: Email: [email protected] Tel: +86 574-63265968 F CC Confidential Authorization Date: 2025-11-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: Q92-BH-20E1 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD.hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature Jason Wang/Manager NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China

Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT External Photos External Photos Page 1 / 3 External Photos Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT External Photos External Photos Page 2 / 3 Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT External Photos External Photos Page 3 / 3 ***** END *****

Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT Internal Photos Internal Photos Page 1 / 4 Internal Photos Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT Internal Photos Internal Photos Page 2 / 4 Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT Internal Photos Internal Photos Page 3 / 4 Antenna Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF EUT Internal Photos Internal Photos Page 4 / 4 ***** END *****

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.0(2024/11/01) Page 1 of 6 TR-4-E-R062 TEST REPORT Applicant Name : NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. Address : NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China Report Number : 2504Y08471E-RF FCC ID: Q92-BH-20E1 Test Standard (s) 47 CFR §1.1307 & §2.1093 Sample Description Product Type: Remote Control Transmitter Model No.: BH-20E Trade Mark: N/A Date Received: 2025-10-17 Report Date: 2025-12-11 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob.Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF Rev:A/4.0(2024/11/01) Page 2 of 6 TR-4-E-R062 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 3 GENERAL INFORMATION ............................................................................................................................ 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 4 OBJECTIVE ................................................................................................................................................... 4 TEST FACILITY .............................................................................................................................................. 4 RF EXPOSURE .............................................................................................................................................. 5 APPLICABLE STANDARD ................................................................................................................................. 5 TEST RESULT: .............................................................................................................................................. 5 EXHIBIT A-EUT PHOTOGRAPHS ................................................................................................................ 6 Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF Rev:A/4.0(2024/11/01) Page 3 of 6 TR-4-E-R062 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision Rev.00 2504Y08471E-RF Original Report 2025-12-11 Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF Rev:A/4.0(2024/11/01) Page 4 of 6 TR-4-E-R062 GENERAL INFORMATION Product Description for Equipment under Test (EUT) Product Name Remote Control Transmitter Tested Model BH-20E Voltage Range # DC 12.0V from battery Frequency Range 433.92MHz Maximum E-field Strength 88.24dBuV/m@3m Modulation Technique OOK Antenna Specification # Internal Antenna (It is provided by the applicant.) Sample Serial Number 3BDW-1, 3BDW-2 (Assigned by ATC, Shenzhen) Sample/EUT Status Good condition Objective This test report is in accordance with Part 1-Subpart I and Part 2-Subpart J, Radiofrequency Radiation Exposure of the Federal Communication Commission rules. The tests were performed in order to determine compliance with §1.1307 & §2.1093 rules. Test Facility The test site used by Shenzhen Accurate Technology Co., Ltd. to collect test data is located on the Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Accredited by American Association for Laboratory Accreditation (A2LA).The Certificate Number is 4297.01. Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF Rev:A/4.0(2024/11/01) Page 5 of 6 TR-4-E-R062 RF EXPOSURE Applicable Standard According to FCC §2.1093 and §1.1307(b), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB 447498 D04 Interim General RF Exposure Guidance v01, clause 2.1.2 – 1-mW test Exemption: Per § 1.1307(b)(3)(i)(A), a single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption applies to all operating configurations and exposure conditions, for the frequency range 100 kHz to 100 GHz, regardless of fixed, mobile, or portable device exposure conditions. This is a standalone exemption, and it cannot be applied in conjunction with any other test exemption. Test Result: For worst case: Mode Frequency Maximum Power 1-mW test Exemption (MHz) (dBm) (mW) SRD 433.92 -6.96 0.2 Yes Note: E(dBuV/m)=EIRP(dBm)-95.2 for distance 3m Use the highest E-field strength(88.24 dBuV/m) for the evaluation, so the EIRP= 88.24 dBuV/m-95.2=-6.96 dBm Result: Compliance. Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF Rev:A/4.0(2024/11/01) Page 6 of 6 TR-4-E-R062 EXHIBIT A-EUT PHOTOGRAPHS Please refer to the Attachment No.1 2504Y08471E-RF EUT External Photos and Attachment No.2 2504Y08…

Text truncated - open the document above for the full version.

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.0(2024/11/01) Page 1 of 27 TR-4-E-R010 TEST REPORT Applicant Name: NINGBO BAIHUANG ELECTRIC APPLIANCES CO., LTD. Address: NO.180,YANSHAN RD,HUXIMEN,HENGHE TOWN,CIXI,NINGBO,315318,China Report Number: 2504Y08471E-RF-00A FCC ID: Q92-BH-20E1 Test Standard (s) FCC PART 15.231 Sample Description Product Name: Remote Control Transmitter Model No.: BH-20E Trade Mark: N/A Date Received: 2025-10-17 Report Date: 2025-12-11 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob.Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2504Y08471E-RF-00A Rev:A/4.0(2024/11/01) Page 2 of 27 TR-4-E-R010 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 3 GENERAL INFORMATION ............................................................................................................................ 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 4 OBJECTIVE ................................................................................................................................................... 4 TEST METHODOLOGY .................................................................................................................................... 4 TEST FACILITY .............................................................................................................................................. 4 MEASUREMENT UNCERTAINTY ....................................................................................................................... 4 SYSTEM TEST CONFIGURATION ............................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION......................................................................................................... 5 EUT EXERCISE SOFTWARE AND POWER LEVEL # ............................................................................................ 5 SPECIAL ACCESSORIES ................................................................................................................................. 5 EQUIPMENT MODIFICATIONS .......................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................... 5 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 6 SUMMARY OF TEST RESULTS ................................................................................................................... 7 TEST EQUIPMENT LIST ............................................................................................................................... 8 ANTENNA REQUIREMENT........................................................................................................................... 9 APPLICABLE STANDARD ................................................................................................................................. 9 ANTENNA CONNECTOR CONSTRUCTION ......................................................................................................... 9 RADIATED EMISSIONS .............................................................................................................................. 10 APPLICABLE STANDARD ............................................................................................................................... 10 EUT SETUP ................................................................................................................................................ 10 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP .................................................................................. 12 TEST PROCEDURE ...................................................................................................................................... 12 CALCULATION ............................................................................................................................................. 12 TEST DATA ................................................................................................................................................. 13 DEACTIVATION TESTING .......................................................................................................................... 22 APPLICABLE STANDARD ............................................................................................................................... 22 TEST PROCEDURE ...........................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF-00A Test Photos Test Photos Page 1 / 2 Radiated Spurious Emissions Test View (9kHz-30MHz) Radiated Spurious Emissions Test View (30MHz- 1GHz) Shenzhen Accurate Technology Co., Ltd. No.: 2504Y08471E-RF-00A Test Photos Test Photos Page 2 / 2 Radiated Spurious Emissions Test View (Above 1GHz) ***** END *****