Q9OWMA1K2K3KWireless Bluetooth Music Interface Adaptor

Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 4 of 6 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 7. EUT connected to the host device via the in-car integration cable 8. EUT and the in-car integration cable ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 5 of 6 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 9. The host device and the in-car integration cable connectors

ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 1 of 4 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 1. 2. ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 2 of 4 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 3. 4. ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 3 of 4 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 5. 6.

LABEL’S LOCATION 15 * 4 mm FCC ID:Q9OWMA1K2K3K

ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 6 of 6 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 10. 11.

Statement of Justification and Compliance for SAR Test Exclusion Product: Wireless Bluetooth Music Interface Adaptor FCC ID: Q9OWMA1K2K3K Manufacturer: Triamp Technology Ltd. Brand: ViseeO Model: WMA1000 and serial models According to FCC KDB 447498 D01 General RF Exposure Guidance v05 4.3.1. Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, 16 where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. For the present device, the declared output power is 4dBm with +/- 0.5dB tolerance. So, max. power of channel, including tune-up tolerance = 2.818 mW (4.5dBm) min. test separation distance = 5 mm f(GHz) = 2.480 [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] = (2.818 / 5) · (√2.480) = 0.89 ≤ 3.0 Hence the SAR Exclusion Threshold condition is satisfied and the SAR evaluation for general population exposure conditions is not required.

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Wireless Bluetooth Music Interface Adaptor Model : WMA1000 FCC ID : Q9OWMA1K2K3K for APPLICANT : Triamp Technology Ltd. ADDRESS : 3F No. 2 Alley 16 Lane 235 Bao Chiao Road,Hsin- Tien District,New Taipei City, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5, DINGFU VIL., LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : 13-01-RBF-016-03 ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : Triamp Technology Ltd. One ViseeO Way 4B-8 Secaucus, NJ 07094 Manufacture : Triamp Technology Ltd. One ViseeO Way 4B-8 Secaucus, NJ 07094 Description of Device : a) Type of EUT : Wireless Bluetooth Music Interface Adaptor b) Trade Name : ViseeO c) Model No. : WMA1000 d) Serial Model : WMA1000+,WMA2000,WMA3000,WMA5000,WMAxxx e) Power Supply : DC 12V Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission N/A Hopping Channel Separation Pass Number of Hopping frequencies used Pass Hopping Channel Bandwidth Pass Dwell Time of each frequency Pass Output Power Requirement Pass 100 kHz Bandwidth of Frequency Band Edges Requirement Pass Out-of-Band Conducted Emission Requirement Pass ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Rev. No 1.0 Date Test Item Received : Jan. 20, 2013 Date Test Campaign Completed : Jan. 31, 2013 Date of Issue : Feb. 26, 2013 Test Engineer : ( Jiapeng Chen, Engineer ) Approve & Authorized : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Test Methodology ........................................................................................................................ 1 1.3 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 6 2.5 User Information .......................................................................................................................... 6 3 SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure............................................................................................................... 8 4.3 Measuring Instrument ................................................................................................................ 10 4.4 Radiated Emission Data ............................................................................................................. 11 4.5 Field Strength Calculation.......................................................................................................... 17 4.6 Photos of Radiation Measuring Setup........................................................................................ 18 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 19 5.1 Description ................................................................................................................................. 19 6 ANTENNA REQUIREMENT .................................................................................................... 20 6.1 Standard Applicable ................................................................................................................... 20 6.2 Antenna Construction................................................................................................................. 20 7 HOPPING CHANNEL SEPARATION..................................................................................... 21 7.1 Standard Applicable ................................................................................................................... 21 7.2 Measurement Procedure......................…

Text truncated - open the document above for the full version.

ETC Report No. : 13-01-RBF-016-03 FCC ID.: Q9OWMA1K2K3K Sheet 18 of 98 Sheets Rev. No 2.1 4.6 Photos of Radiation Measuring Setup