QCD15II500ARA-RFInfrared Heater RF

1 MODEL # 15II500ARA BATH VANITY WITH HEATER INSTRUCTION MANUAL For Customer Service: www.twinstarhome.com 866-661-1218 8:30 a.m. - 5:30 p.m., EST, Monday-Friday IMPORTANT: RETAIN FOR FUTURE REFERENCE READ CAREFULLY Questions, problems, missing parts? Twin-Star International, Inc. Delray Beach, FL 33445 Made in China Printed in China ©2012, Twin-Star International, Inc. V020917 2 Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product or assembly, please call customer service at 1-866-661-1218, 8:30 a.m.-5:30 p.m., EST, Monday-Friday. When using electrical appliances always follow basic precautions to reduce the risk of     shock, and injury to persons including the following: 1. Read all instructions before using this appliance. 2. This appliance is hot when in use. To avoid burns do not touch hot surfaces with bare skin. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 ft / 0.9 m from the front of this appliance. WARNING: In order to avoid overheating do not cover the heater. WARNING: Use extreme caution when operating heater near children and the invalid. 3. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given instruction or are being supervised. 4. This appliance is not a toy. Supervise children when they are close to heater. 5. If possible, always unplug this appliance when not in use. 6. Do not operate any heater with a damaged cord or plug, after the appliance malfunctions, or if it has been dropped or damaged in any manner. 7. If the supply cord is damaged it must be replaced by the manufacturer, it’s service agent or similarly                                     !   must be replaced prior to operating this heater again. 10. Do not use outdoors. 11. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord  " !  !   " "     12. To disconnect this appliance turn controls to the off position and then remove plug from outlet. 13. Connect to properly grounded outlets only. 14. This appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or for U.S.A. installations, follow local codes and the National Electrical Code, ANSI/NFPA NO.70. 15. The heater must not be located immediately below a socket-outlet. 16. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause    $       %&'    $   $(     )  !  surfaces, like a bed, where opening may become blocked. 18. This appliance has hot and arcing or sparking parts inside. Do not use in areas where gasoline,   *      '         $! clothing. Do not hang Christmas stockings or other decorations on or near this product. 19. Use this appliance only as described in the manual. Any other use not recommended by the   !      $ +   20. There is a thermostat limiter inside the heater. When inner temperature is overheating or abnormal heating occurs the thermostat protective device will cut off the power supply to avoid damage to the   $! IMPORTANT INSTRUCTIONS 3 21. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). 22. Reference Fig. 1 for grounding instructions. This heater is for use on 120 volts. The cord has a plug as shown in Fig. 1A. An adapter as shown in Fig.1C is available for connecting three-blade grounding type plugs to two-slot receptacles. The grounding pin extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. B A CD Fig. 1 IMPORTANT INSTRUCTIONS SAVE THESE INSTRUCTIONS Grounding Pin Cover Of Grounded Outlet Box Metal Screws Adapter Grounding Means Grounding Pin For product warranty registration please visit: www.twinstarhome.com/registration Before setting up this product please record the model number and serial number of this product in the spaces below for registration and warranty reference. Heater Model NumberSerial Number 4 PACKAGE CONTENTS Fig. 2 Bath Vanity with Heater Touch-up Pen Remote Control Wall Mounted Remote Holder HARDWARE CONTENTS Counter-top Remote Stand PartDescriptionQuantity ABath Vanity with Heater1 B Remote Control1 CTouch-up Pen1 DCounter-top Remote Stand1 EWall Mounted Remote Holder1 A B C D E Screw 0.2 in. x 1.5 in. AA x 3 5 HEATER LOCATION CLEARANCE TO COMBUSTIBLES CLEANING TRIM ELECTRICAL CONNECTION When choosing a location for your new heater be sure that the general instructions are followed. Also, for best ef fect, install the heater out of direct sunlight. Keep electrical cords, drapery, furniture and other combustibles at least 3 feet (0.9 m) from the front and sides of the heater. Clean the trim using a soft cloth, slightly dampened with citrus oil based product and buff with a clean soft cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained at supermarkets or hardware stores. =%>=?%@JQ XJY  "   grounded outlet is required. Preferably, the heater will be on a dedicated circuit as other appliances on the same circuit may cause the circuit bre…

Text truncated - open the document above for the full version.

Twin-Star International Inc. September 28, 2012 To: SIEMIC, INC. 775 Montague Expressway Milpitas , CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ______ Twin-Star International Inc. ___hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Description: Infrared Heater RF Model name: 15II500ARA-RF FCC ID: QCD15II500ARA-RF We affirm that between SIEMIC and __ Twin-Star International Inc. ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature: Client’s name / title: Dale Duan / Manager Contact information / address: 12/F Taiwanese Trade Association Building, De Zheng Road, ChangAn Town, Dongguan City, China

SCS-F19: Confidentiality Request Letter Page 1 of 1 Rev 2.0 Twin-Star International Inc. September 28, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: QCD15II500ARA-RF We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Client’s signature: Client’s name / title: Dale Duan / Manager Contact information / address: 12/F Taiwanese Trade Association Building, De Zheng Road, ChangAn Town, Dongguan City, China

FCC Certification label Sample FCC ID: QCD15II500ARA-RF This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Certification Label Location Sample Label location

Antenna

Page 1 of 33 FCC ID: QCD15II500ARA-RF ACCURATE TECHNOLOGY CO., LTD REPORT NO. ATE20122271 APPLICATION CERTIFICATION On Behalf of Twin-Star International Inc. Infrared Heater RF Model No.: 15II500ARA-RF FCC ID: QCD15II500ARA-RF Prepared for : Twin-Star International Inc. Address : 12/F Taiwanese Trade Association Building, De Zheng Road, ChangAn Town, Dongguan City, China Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20122271 Date of Test : September 26-29, 2012 Date of Report : September 29, 2012 Page 2 of 33 FCC ID: QCD15II500ARA-RF ACCURATE TECHNOLOGY CO., LTD REPORT NO. ATE20122271 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................5 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. SUMMARY OF TEST RESULTS................................................................................................... 7 4. THE FIELD STRENGTH OF RADIATION EMISSION ............................................................ 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. The Field Strength of Radiation Emission Measurement Limits..............................................................9 4.3. Configuration of EUT on Measurement ...................................................................................................9 4.4. Operating Condition of EUT ....................................................................................................................9 4.5. Test Procedure ........................................................................................................................................10 4.6. The Field Strength of Radiation Emission Measurement Results ..........................................................11 5. 20DB OCCUPIED BANDWIDTH ................................................................................................ 13 5.1. Block Diagram of Test Setup..................................................................................................................13 5.2. The Bandwidth of Emission Limit According To FCC Part 15 Section 15.231(c) ................................13 5.3. EUT Configuration on Measurement .....................................................................................................14 5.4. Operating Condition of EUT ..................................................................................................................14 5.5. Test Procedure ........................................................................................................................................14 5.6. Measurement Result ...............................................................................................................................15 6. RELEASE TIME MEASUREMENT............................................................................................ 16 6.1. Block Diagram of Test Setup..................................................................................................................16 6.2. Release Time Measurement According To FCC Part 15 Section 15.231(a) ..........................................16 6.3. EUT Configuration on Measurement .....................................................................................................17 6.4. Operating Condition of EUT ..................................................................................................................17 6.5. Test Procedure ........................................................................................................................................17 6.6. Measurement Result ...............................................................................................................................18 7. AVERAGE FACTOR MEASUREMENT .................................................................................... 19 7.1. Block Diagram of Test Setup..................................................................................................................19 7.2. Average factor Measurement according to ANSI 63.10: 2009...............................................................19 7.3. EUT Configuration on Measurement .....................................................................................................20 7.4. Operating Condition of EUT ..................................................................................................................20 7.5. Test Procedure ........................................................................................................................................20 7.6. Measurement Result ...............................................................................................................................21 8. ANTENNA REQUIREMENT........................................................................................................ 22 8.1. The Requirement ....................................................................................................................................22 8.2. Antenna Construction .........................................................................…

Text truncated - open the document above for the full version.

Radiated emissions test 30MHz- 1GHz Radiated emissions test > 1GHz