QKGRDX-U3Mobile Transmitter

OPERATION The RDX series RF modules are designed for integration into various radio systems products. The module has no user controls as such and is designed for use in applications such as low power control stations and mobile relay /mobile repeater stations, where other 3rd party circuitry will provide for user interface and controls. The modules are based on Motorola ASTRO XTS3000 series poratble radios. The modules interface connector provides standard input/output audio interfaces, logic indication of squelch conditions, and logic level selection of the pre-programmed channels/personality modes, in addition to serial bus control. Various parameters including RF Power is programmable via a Motorola XTS3000 Radios Service Software (RSS) from 1-3Watts on 800MHz models, 1-4watts on UHF modules and 1-5 watts on VHF models. NOTE: RF Power output MUST be set so as to not exceed the permissable FCC regulatory level prior to the units deployment. The module is designed to connect to a unity gain 1/4 wave antenna. Other antennas may only be used providing they ensure the installation continues to comply with FCC licensing requirements. DC POWER: The RDX series modules are designed for operation from a nominal 7.5VDC source. The unit will operate within specification over a voltage range from 6.0 to 8.4Volts DC. Current consumption for the module is 120mA on standby. Installation: The RDX modules must be installed using best RF engineering practice. The units are shielded to minimize RF interference from other co-located transceivers but attention should be made to frequency planning to ensureunwanted interfernce, intermodulation or Receiver desensitization occurs. There small compact size, low current consumption make them ideal for incorporation into emergency battery powered portable repeaters, temporary remote rf Control station and other relation mobile applications. Product of New Zealand /Motorola XTS3000 radios Made in USA ASTRO & XTS3000 are trademarks of Motorola Inc. RDX Series RF Module User Guide SECURE / ENCRYPTION OPERATION ( Optional) RDX RF modules may optionally fitted with Motorola ASTRO XTS3000 encryption modules. Encrypted mode should be slaved to the 16 programmable modes. Only one encryption key is available. Keys can be entered using a standard Motorola Key Loader and an appriate interface cable . General Safety. NEVER hold the antenna when theRF Module is “IN USE”. Keep all parts of the body at least 8inches ( 20cm) from Antenna whip. ELECTROMAGNETIC INTERFERENCE Most electronic devices are susceptible to electromagnetic interference (EMI). To avoid electromagnetic interference and/or compatibility conflicts, turn off the X-Ponder anywhere posted notices instruct you to do so. The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 centimeters) be maintained between a wireless radio and a pacemaker. Turn the unit OFF immediately if you feel that interference is taking place. Digital radios may interfere with some types of hearing aids. If such interference occurs, you may want to consult ithe aids manufacturer. EXPLOSIVE ATMOSPHERES Do not operate the X-Ponder in any area with a potentially explosive atmosphere. Areas such as fueling areas, chemical handling facilities, or areas where the air contains chemicals or particles, such as grain dust or metal powders. NEVER charge,remove or install batteries as sparks in such a potentially explosive atmosphere can cause an explosion or fire resulting in injury or death. To avoid possible interference with blasting operations, do not operate the module near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Always obey all signs and instructions. ELECTROMAGNETIC ENERGY (EME) The Motorola XTS3000 radios inside are designed to comply with the following international standards and guidelines regarding exposure of humans to electromagnetic energy (EME): • USA Federal Communications Commission, Regulations; 47 CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-199 Edition • USA National Council on Radiation Protection and Measurements, Report 86, 1986 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Wireless Pacific Wireless Pacific

Digital XTS 3000 Portable Radios Basic Service Manual Motorola8000 West Sunrise BoulevardFort Lauderdale, Florida 33322 68P81083C85-O TM TM *6881083C85* Foreword This manual covers all models of ASTRO™ Digital XTS 3000™ portable radios, unless otherwise specified. It includes all the information necessary to maintain peak product performance and maximum working-time using the pass/fail service approach. This basic level of service is typical of some local service centers, self-maintained customers, and some distributors. Included in this manual are: radio specifications for the 800MHz frequency band; a general description of ASTRO Digital XTS 3000 models; recommended test equipment, service aids, and tools; radio alignment procedures; fundamental disassembly/ reassembly procedures; and general maintenance recommendations. For details on the operation of the radio, or board- or component-level troubleshooting, refer to the applicable manuals available separately. To help you with your selection, a list is provided in this manual, titled “Related Publications.” Safety Information In 1991 the Institute of Electrical and Electronics Engineers (IEEE), and in 1992 the American National Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. Over 120 scientists, engineers, and physicians from universities, government health agencies, and industry, after reviewing the available body of research, developed this updated Standard. In March, 1993, the Federal Communications Commission (FCC) proposed the adoption of this updated Standard. Motorola subscribes to the same safety standard for the use of its products. Proper operation of this radio will result in user exposure substantially below FCC recommended limits: • DO NOT hold the radio with the antenna very close to, or touching, exposed parts of the body, especially the face, ears, or eyes, while transmitting. Hold the radio in a vertical position with the microphone two to three inches away from the lips. • DO NOT hold the transmit switch (PTT) on when not actually desiring to transmit. • DO NOT allow children to play with any radio equipment containing a transmitter. • DO NOT operate this equipment near electrical blasting caps or in an explosive atmosphere. Under certain conditions, radios can interfere with blasting operations. When you are in the vicinity of construction work, look for, and observe, signs cautioning against radio transmissions. If radio transmission is prohibited, you must not transmit until out of the area. Furthermore, you must turn off your radio to prevent any accidental transmission. • DO NOT replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion. • Turn the radio off when removing or installing a battery. Anyone intending to use a radio in a hazardous area is advised to become familiar with the subject of intrinsic safety and with Section 70 of the National Fire Code, which is commonly referred to as Article 500 of the National Electric Code. Use of anything but factory supplied components may affect the approval and safety of the radio. Likewise, it is advised that servicing should be performed only by qualified personnel who adhere to the following Factory Mutual (FM) required warning: Modification of FM approved intrinsically safe radios will negate Factory Mutual Research Corporation (FMRC) approval. Airbag Warning Statement VEHICLES EQUIPPED WITH AIR BAGS An air bag inflates with great force. DO NOT place objects, including communication equipment, in the area over the air bag or in the air bag deployment area. If the communication equipment is improperly installed and the air bag inflates, this could cause serious injury. • Installation of vehicle communication equipment should be performed by a professional installer/technician qualified in the requirements for such installations. An air bag’s size, shape and deployment area can vary by vehicle make, model and front compartment configuration (for example, bench seat vs. bucket seats). • Contact the vehicle manufacturer’s corporate headquarters, if necessary, for specific air bag information for the vehicle make, model and front compartment configuration involved in your communication equipment installation. Manual Revisions Changes which occur after this manual is printed are described in “FMRs.” These FMRs provide complete information on changes including pertinent parts listing data. ! W A R N I N G ! ! W A R N I N G ! i Table of Contents Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . inside front cover List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Portable Radio Model Numbering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii SPECIFICATIONS FOR 800MHz RADIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 - Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

OPERATIONThe RDX series RF modules are designed for integration into various radio systems products. The module has no user controls as such and is designed for use in applications such as low power control stations and mobile relay / mobile repeater stations, where other 3rd party circuitry will provide for user interface and controls. The m odules are based on Motorola ASTRO XTS3000 series portable radios.The modules interface connector provides standard input/output audio interfaces, logic indication of squelch conditions, and logic level selection of the preprogrammed channels/personality modes, in addition to key loading and RSS use. Various parameters including RF Power is programmable via a Motorola XTS3000 Radios Service Software (RSS) from 1-3Watts on 800MHz models, 1-4watts on UHF modules and 1-5 watts on VHF models. NOTE: RF Power output MUST be set so as to not exceed the permissible FCC regulatory level prior to the units deployment. The module is designed to connect to a unity gain 1/4 wave antenna such as a vehicle roof mount antenna. Other antennas may only be used providing they ensure the installation continues to comply with FCC licensing requirements. Ensure Antenna is always at least 20cm away from human contact.DC Power RDX series modules are designed for operation from a nominal 7.5VDC source. The unit will operate within specification over a voltage range from 6.0 to 8.4Volts DC. Current consumption fo r the module is 120mA on standby. Installation:The RDX modules must be installed using best RF engineering practice taking into account required operation, FCC licensing and EME requirements. The units are shielded to minimize RF interference from other co-located transceivers but attention should be made to frequency planning to ensure unwanted interference, intermodulation or receiver desensitization occurs. Their small compact size, low current consumption make them ideal for incorporation into emergency battery powered portable repeaters, temporary remote RF Control station and other related mobile applications.Product of New Zealand /Motorola XTS3000 radios Made in USA ASTRO & XTS3000 are trademarks of Motorola Inc... RDX Series RF Module User Guide SECURE / ENCRYPTION OPERATION ( Optional) RDX RF modules may optionally fitted with Motorola ASTRO XTS3000 encryption modules.Encrypted mode should be slaved to the 16 programmable modes. Keys can be entered using a standard Motorola Key Loader and an appropriate interface cableGeneral Safety.NEVER hold the antenna when the RF Module is “IN USE”. Keep all parts of the body at least 8 inches ( 20cm) from Antenna whip.ELECTROMAGNETIC INTERFERENCEMost electronic devices are susceptible to electromagnetic interfe rence (EMI). To avoid electromagnetic interference and/or compatibility conflicts, turn off the RF module anywhere posted notices instruct you to do so. The Health Industry Manufacturers A ssociation recommends that a minimum separation of 6 inches (15 centimetres) be maintained between a wireless radio and a pacemaker. Turn the unit OFF immediately if you feel that interference is taking place. Digital radios may interfere with some types of hearing aids. If such interference occurs, you may want to consult the aids manufacturer.EXPLOSIVE ATMOSPHERESDo not operate the RF module in any area with a potentially explosive atmosphere. Areas such as fueling areas, chemical handling facilities, or areas where the air contains chemicals or particles, such as grain dust or metal powders. NEVER charge, remove or install batteries as sparks in such a potentially explosive atmosphere can cause an explosion or fire resulting in injury or death. To avoid possible interference with blasting operations, do not operate the module near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Always obey all signs and instructions.ELECTROMAGNETIC ENERGY (EME)The Motorola XTS3000 radios inside are designed to comply with the following international standards and guidelines regarding exposure of humans to electromagnetic energy (EME): • USA Federal Communications Commission, Regulations; 47 CFR part 2 sub-part J• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992• Institute of Electrical and Electronic Engineers (IEEE) C95.1-199 Edition• USA National Council on Radiation Protection and Measurements, Report 86, 1986• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Wir e l ess P ac ifi c Wi reless Pacific

OPERATIONThe RDX series RF modules are designed for integration into various radio systems products. The module has no user controls as such and is designed for use in applications such as low power control stations and mobile relay / mobile repeater stations, where other 3rd party circuitry will provide for user interface and controls. The modules are based on Motorola ASTRO XTS3000 series portable radios.The modules interface connector provides standard input/output audio interfaces, logic indication of squelch conditions, and logic level selection of the preprogrammed channels/personality modes, in addition to key loading and RSS use. Various parameters including RF Power is programmable via a Motorola XTS3000 Radios Service Software (RSS) from 1-3 watts on 800MHz models, 1-4 watts on UHF modules and 1-5 watts on VHF models. NOTE: RF Power output MUST be set so as to not exceed the permissible FCC regulatory level prior to the units deployment. The module is designed to connect to a unity gain 1/4 wave antenna such as a vehicle roof mount antenna. Other antennas may only be used providing they ensure the installation continues to comply with FCC licensing requirements. Ensure Antenna is always at least 20 inches away from human contact.DC Power RDX series modules are designed for operation from a nominal 7.5VDC source. The unit will operate within specification over a voltage range from 6.0 to 8.4Volts DC. Current consumption fo r the module is 120mA on standby. A 3A fast blow fuse or similiar device should be wired in series. Installation:The RDX modules must be installed using best RF engineering practice taking into account required operation, FCC licensing and EME requirements. The units are shielded to minimize RF interference from other co-located transceivers but attention should be made to frequency planning to ensure unwanted interference, intermodulation or receiver desensitization occurs. Their small compact size, low current consumption make them ideal for incorporation into emergency battery powered portable repeaters, temporary remote RF Control station and other related mobile applications. Product of New Zealand /Motorola XTS3000 radios Made in USA ASTRO & XTS3000 are trademarks of Motorola Inc... RDX Series RF Module User Guide SECURE / ENCRYPTION OPERATION ( Optional) RDX RF modules may optionally fitted with Motorola ASTRO XTS3000 encryption modules.Encrypted mode should be slaved to the 16 programmable modes. Keys can be entered using a standard Motorola Key Loader and an appropriate interface cableGeneral Safety.NEVER hold the antenna when the RF Module is “IN USE”. Keep all parts of the body at least 20 inches ( 50cm) from Antenna whip.ELECTROMAGNETIC INTERFERENCEMost electronic devices are susceptible to electromagnetic interfe rence (EMI). To avoid electromagnetic interference and/or compatibility conflicts, turn off the RF module anywhere posted notices instruct you to do so. The Health Industry Manufacturers Association recommends that a minimum separation of 6 inches (15 centimetres) be maintained between a wireless radio and a pacemaker. Turn the unit OFF immediately if you feel that interference is taking place. Digital radios may interfere with some types of hearing aids. If such interference occurs, you may want to consult the aids manufacturer.EXPLOSIVE ATMOSPHERESDo not operate the RF module in any area with a potentially explosive atmosphere. Areas such as fueling areas, chemical handling facilities, or areas where the air contains chemicals or particles, such as grain dust or metal powders. NEVER charge, remove or install batteries as sparks in such a potentially explosive atmosphere can cause an explosion or fire resulting in injury or death. To avoid possible interference with blasting operations, do not operate the module near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Always obey all signs and instructions.ELECTROMAGNETIC ENERGY (EME)The Motorola XTS3000 radios inside are designed to comply with the following international standards and guidelines regarding exposure of humans to electromagnetic energy (EME):• USA Federal Communications Commission, Regulations; 47 CFR part 2 sub-part J• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992• Institute of Electrical and Electronic Engineers (IEEE) C95.1-199 Edition• USA National Council on Radiation Protection and Measurements, Report 86, 1986• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Wir e l ess P ac ifi c Wi reless Pacific

AT T E S TAT I O N The Wireless Pacific WH09UCC9PW5R (QKGRDX-U3) UHF Mobile Transceiver complies with the Code of Federal Regulations (CFR) 47 Part 90 –Private Land Mobile Services. This report describes the tests and measurements performed for the purpose of determining compliance with the specification with the following conditions: The client selected the test sample. The report relates only to the sample tested. This report does not contain corrections or erasures. Measurement uncertainties with statistical confidence intervals of 95% are shown below test results. Both Class A and Class B uncertainties have been accounted for, as well as influence uncertainties where appropriate. In addition this equipment has been tested in accordance with the requirements contained in the appropriate Commission regulations. To the best of my knowledge, these tests were performed using measurement procedures that are consistent with industry or Commission standards and demonstrate that the equipment complies with the appropriate standards. I further certify that the necessary measurements were made by EMC Technologies NZ Ltd, 47 MacKelvie Street, Grey Lynn, Auckland, New Zealand. Andrew Cutler General Manager EMC Technologies NZ Ltd

MERRY CHRISTMAS AND A HAPPY NEW YEAR TO ALL OF THE FCC CERTIFICATION TEAM FROM THE TEAM AT EMC TECHNOLOGIES NZ LTD

Device tested Test interface box

Label Label Location

Internal View

Additional Internal photographs Overall view of each circuit board. Unfortunately these ones did not turn out to good.

Vocoder board

Radio assembly

Transceiver board

Vocoder board Controller board

EXHIBIT 8D FCC ID: QKGRDX-U3 POWER LIMITING The transmitter RF Power is regulated by a close loop ALC ( Automatic Level Control) circuit. Forward power of the PA output is sensed by a directional coupler and detector network. The detected voltage (V DET) which represents the power level is fed back to the ALC IC. Here it is compared to a reference voltage (V REF) supplied by the D/A IC. The ALC will then vary the control voltage (V CONT) of the RF power amplifier to reduce its gain until the correlation between V DET and V REF is established. Thus the power output is automatically maintained at a constant level regardless of any disturbances that may occur in the transmitting system.

EXHIBIT 8 C FCC ID: QKGRDX-U3 HARMONIC SUPPRESSION CIRCUIT Circuit Description: Attentuation for harmonics is provided by a low pass filter in the RF Power Amplifier and the Antenna Switch. The low pass filter in the RF PA is composed of L1, L2, C1 and C2. The low pass filter in the Antenna Switch is composed of L3, L4, C3 and C4. There also exist a zero at 2fo (L3,C3) in the antenna switch. Circuit diagram: C1C2 L1L2 RF Power Amp Module B+ in C5 C4 L4 L3 out Antenna switch

Exhibit 8A FCC ID: QKGRDX-U3 CARRIER FREQUENCY GENERATION AND STABLIZATION Circuit Description: The carrier frequency is generated using a fractional-N frequency synthesizer. This consists of a phase- locked loop circuit with a voltage controlled oscillator (VCO) whose output is fed back to a programmable divider chain. The divide ratios are determined from information stored in the memory ICs and bussed to - the synthesizer via a microcomputer. The microcomputer extracts the data for the division ratios as determined by the system select switch or by loading data stored in the memory [Cs. Using a time averaged algorithm a combination of divide ratios are used so that the reference frequency can be a much higher value than the value of the frequency resolution. Modulation occurs by a combination of directly coupling the modulation signal to the low pass filter in the loop and by processing the digitized analog modulation signal to alter the divider values, A temperature compensated crystal oscillator, a 16.8 MHz and stable to 1.5 parts per million over temperature extremes is used for the frequency reference. The 16.8 MHz reference is further divided into one of three reference frequencies which is compared to the divided down VCO output in a phase detector which in turn provides a DC steering voltage back to the VCO. A Block diagram of the VCO/Synthesizer system is attached.

OVERVIEW OF RADIO OPERATION The RDX series RF modules are designed for integration into various radio systems products. The module has no user controls as such and is designed for use in applications such as low power control stations and mobile relay /mobile repeater stations. The modules interface connector provides standard input/output audio interfaces, logic indication of squelch conditions, and logic level selection of the pre-programmed channels/personality modes, in addition to serial bus control. All frequency, deviation, squelch and power settings are pre- programmed into the unit by use of a standard Motorola XTS3000 series Radio Service Software (RSS) run on a PC together with a Radio Interface Box (RIB) and associated programming cables.

Digital XTS 3000 Portable Radios Basic Service Manual Motorola8000 West Sunrise BoulevardFort Lauderdale, Florida 33322 68P81083C85-O TM TM *6881083C85* Foreword This manual covers all models of ASTRO™ Digital XTS 3000™ portable radios, unless otherwise specified. It includes all the information necessary to maintain peak product performance and maximum working-time using the pass/fail service approach. This basic level of service is typical of some local service centers, self-maintained customers, and some distributors. Included in this manual are: radio specifications for the 800MHz frequency band; a general description of ASTRO Digital XTS 3000 models; recommended test equipment, service aids, and tools; radio alignment procedures; fundamental disassembly/ reassembly procedures; and general maintenance recommendations. For details on the operation of the radio, or board- or component-level troubleshooting, refer to the applicable manuals available separately. To help you with your selection, a list is provided in this manual, titled “Related Publications.” Safety Information In 1991 the Institute of Electrical and Electronics Engineers (IEEE), and in 1992 the American National Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. Over 120 scientists, engineers, and physicians from universities, government health agencies, and industry, after reviewing the available body of research, developed this updated Standard. In March, 1993, the Federal Communications Commission (FCC) proposed the adoption of this updated Standard. Motorola subscribes to the same safety standard for the use of its products. Proper operation of this radio will result in user exposure substantially below FCC recommended limits: • DO NOT hold the radio with the antenna very close to, or touching, exposed parts of the body, especially the face, ears, or eyes, while transmitting. Hold the radio in a vertical position with the microphone two to three inches away from the lips. • DO NOT hold the transmit switch (PTT) on when not actually desiring to transmit. • DO NOT allow children to play with any radio equipment containing a transmitter. • DO NOT operate this equipment near electrical blasting caps or in an explosive atmosphere. Under certain conditions, radios can interfere with blasting operations. When you are in the vicinity of construction work, look for, and observe, signs cautioning against radio transmissions. If radio transmission is prohibited, you must not transmit until out of the area. Furthermore, you must turn off your radio to prevent any accidental transmission. • DO NOT replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion. • Turn the radio off when removing or installing a battery. Anyone intending to use a radio in a hazardous area is advised to become familiar with the subject of intrinsic safety and with Section 70 of the National Fire Code, which is commonly referred to as Article 500 of the National Electric Code. Use of anything but factory supplied components may affect the approval and safety of the radio. Likewise, it is advised that servicing should be performed only by qualified personnel who adhere to the following Factory Mutual (FM) required warning: Modification of FM approved intrinsically safe radios will negate Factory Mutual Research Corporation (FMRC) approval. Airbag Warning Statement VEHICLES EQUIPPED WITH AIR BAGS An air bag inflates with great force. DO NOT place objects, including communication equipment, in the area over the air bag or in the air bag deployment area. If the communication equipment is improperly installed and the air bag inflates, this could cause serious injury. • Installation of vehicle communication equipment should be performed by a professional installer/technician qualified in the requirements for such installations. An air bag’s size, shape and deployment area can vary by vehicle make, model and front compartment configuration (for example, bench seat vs. bucket seats). • Contact the vehicle manufacturer’s corporate headquarters, if necessary, for specific air bag information for the vehicle make, model and front compartment configuration involved in your communication equipment installation. Manual Revisions Changes which occur after this manual is printed are described in “FMRs.” These FMRs provide complete information on changes including pertinent parts listing data. ! W A R N I N G ! ! W A R N I N G ! i Table of Contents Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . inside front cover List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.