QLWSM700RCar Alarm Transceiver

FCC ID: QLWSM700S, QLWSM700R TWO-WAY FM BRAIN, REMOTE USER’S MANUAL ACE SECURITY INC. TABLE OF CONTENTS 1. Safety Information......................................................... page 3 2. Remote Pager....................................................................... 3 3. Visual LCD .......................................................................... 3 4. Functions of remote buttons................................................... 4 5. Explanation of features 1) Lock/Unlock(Arm/Disarm)................................................... 5 2) Panic................................................................................. 6 3) Car Find............................................................................. 6 4) Trunk Release..................................................................... 6 5) Programming Confirmation................................................... 6 6) Remote Start....................................................................... 6 7) Aux 1 and Aux 2.................................................................. 6 8) Programming(Manu) Mode.................................................... 6 6. Programming Features 1) Siren On/Off....................................................................... 7 2) Override(valet) Mode........................................................... 7 3) Last Door Arming................................................................ 7 4) Cold Start........................................................................... 7 5) Engine Start Reservation...................................................... 7 6) Remote Start Memory.......................................................... 8 7) IG Lock.............................................................................. 8 8) Turbo Mode........................................................................ 8 9) Shock Sensor On/Off........................................................... 8 10) Receipt of Signal Disable.................................................... 8 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This Device may not cause harmful interference and (2) This Device must accept any interference received, Including interference that may cause undesired operation. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1. Safety Information Please take these safety precautions under the following conditions 1) Servicing the vehicle When servicing your vehicle (i.e. washing your car), the ace security system should be in Override(Valet) Mode. There is a safety hood pin switch under the hood that deactivates the remote starter function if the hood is open. However, the vehicle may start when the Start button is pressed for approx. more than 2 seconds even though the hood is open if the switch has been installed improperly or damaged. 2) Loaning your vehicle to others Please put the vehicle in Override(Valet) Mode whenever loan your vehicle to an individual who is not familiar with the Ace Security System. This will prevent the vehicle loaner from activating the Ace Security system accidentally. 3) Remote Start - Do not use the remote to start the vehicle in an enclosed area without sufficient ventilation - Do not use the remote to start the engine if you or someone else is directly behind or in front of the vehicle for the safety purpose - Ensure to engage the parking break and put the transmission in the neutral position or parking position - Do not use the remote to start the vehicle with a person or pet inside of the vehicle 2. Remote Pager This transmitter that allows you to activate multiple functions by setting or pressing the 3 buttons on the remote. Please see the details as described thereafter. 3. Visual LCD The visual color LCD of the remote inform the vehicle owner the security status of your vehicle at all time and the different icons on the remote indicate what your vehicle is doing currently 1) Antenna : Indicates if the remote is transmitting signals to the control module. 2) Siren : Indicates if Siren is turned to on or off 3) Zz : Indicates if your vehicle is in Override(valet) Mode 4) Last door arming : Indicates if Last door arming mode is on or off 5) Cold start : Indicates if Cold start mode is on or off 6) Engine starting reservation : Indicates if Engine starting reservation mode is on or off 7) Engine running time : Displays when you change the engine running time for the remote start function. 8) ERR(Error report) : Displays when the Ace Security system is not operated properly 9) Battery : Displays remaining battery life 10)ATREV : Indicates if the Ace Security system is in Automatic remote start memory mode in a manual transmission vehicle. 11)TURBO : Indicates if Turbo mode is on or off 12)Current time: Indicates the current time 13)IMPT: Indicates if Shock sensor is by-passed or not 14)Melody Alert: Indicates if Melody alert is on or off 15) OFF : Indicates if the receipt of signal with remote is disable 16) P/N : Indicates Parking time or Driving time 17) Trunk : Displays if the trunk is open 18) Door : Displays if the door is open 19) Hood : Displays if the hood is open 20) Wheel : Displays if the engine is started 21) IG Lock : Indicate if Ignition Lock is on or off 22) Lock/Unlock : Displays if the vehicle is armed or disarmed 4. Functions of the remote button No. Buttons Short Long 1 Lock/Unlock Panic 2 Car Find Trunk Release 3 Programming confirmation Remote Start 4 + Aux 1 Aux 2 5 + Programming(Manu) Mode N/A Note. - “ + “ means simultaneously pressing the buttons - A kind of buttons shall described by No. 1, 2, 3 according to above table thereafter. 1) Button No. 1 : Door Lock/Unlock, Panic - Press the button(No.1) shortly for Lock/Unlock - Press the button(No.1) long for Panic - Pr…

Text truncated - open the document above for the full version.

Remote controller - Block Diagram Antenna(Helical TyRX/TX Common use Receiving frequency : 434. 7RX/TX (Transmitting frequency : 41 Switching Block A (RF receiving)Block B (RF transmitting) A1 B1 RF amplify Band pass filter A2 B2 Rf band pass filter 2st amplify A3 B3 1st mixer and AB1 Low pass filter middle frequncy low pass B4 amplify filter 1st amplify A4 AB2 1st middle RF buffer A5 frequncy filter AB3 2st Local A6 Low pass oscillation 2st mixer filter A7 AB4 Quadrature detection an d Local FSK comparator oscillation B5 Block C (Logic)Modulation C1 Rf input C8 C4 Rf Power enable/disable Micro-Controller switching switching (PIC16C924) C5 C2 LCD Display CPU Real time clock C7 C6 C3 In put button DC-DC #NAME? 1, 2, 3 Up-converter Battery(AAA)

Sent: Monday, October 14, 2002 8:23 PM To: Mike Kuo Subject: Re: Ace Security Inc., FCC ID:QLWSM700R, AN02T2310 Dear Mike, Please refer the attached test report file that I revised. Thank you so much. Best Regards, Jeongmin Kim ************************************************ ----- Original Message ----- From: "Mike Kuo" <[email protected]> Sent: Friday, October 11, 2002 6:23 AM Subject: FW: Ace Security Inc., FCC ID:QLWSM700R, AN02T2310 > > > -----Original Message----- > From: CERTADM > Sent: Thursday, October 10, 2002 2:21 PM > To: '[email protected]' > Subject: Ace Security Inc., FCC ID:QLWSM700R, AN02T2310 > > > Notice_content > ------------- > Question #1: Only average reading was provided for emission above 1GHz, per > section 15.231(b)(2) of FCC rules, the peak reading (15.25) is required. > Please provide such data. > > Best Regards > > Mike Kuo / TCB Certifier > The items indicated above must be submitted before processing can continue > on the above referenced application. Failure to provide the requested > information within 60 days of the original e-mail date may result in > application dismissal and forfeiture of the filing fee. Also, please note > that partial responses increase processing time and should not be submitted. > Any questions about the content of this correspondence should be directed to > the e-mail address listed below the name of the sender. >

(External Photos)

(Internal Photos)

Circuit operation explanation ---- Remote rf block diagram ---- a1 a2 a3 a4 Tx data Modulation Local RF buffer RF amplif ya5 oscillation (413.39 MHz) Antenna CPU (Pic16c924) b3 b6 RX /TX 2ST oscilation switching (20.945MHz) b1 b2 b4 b5 Rx FSK i nQuadrature 2ST mixer 1ST mixer RF amplify detection c1 Input button(1,2,3) <Picture 1> - A basic carrier frequency consists of a1, a2, a3 (on picture 1). - Receiver : super heterodyne receve r - Modulation type : FM FSK(frequncy shift keying) - Remote transmitting frequncy : 413.39MH z - Remote receive local oscillation frequncy : 413.39MHz - Remote receive frequncy : 434.79MHz 1. Remote control 1.1 Transmission Press input button(1,2,3) Modulation signal is occurred at CPU(location u1) pin n o Modulation is formed at a1 (VD1), a2 (Q6). a3 (Q7) creates frequency 413.39MHz. The frequency of 413.39MHZ is amplified through the component s of a4(Q8,Q9) and b6(rx/tx switching) and transferred to antenna. 1.2 Receiver A carrier frequency (434.79MHz) amplifies at b5 (Q1, Q2) pass through a5 (antenna b4 (Q3) receives signals of a3 (Q7), b5 and makes 1st IF (21.4MHz) to send b2 (U1 b2 (U1) mixes with 2nd local oscillation frequency (20.945MHz) of b3 (X2) and mak e 455Khz demodulates FM at b1 (X3) and quadrature detects Sends Fsk out to CPU(location u1) pin no 2.

KTL Korea Testing Laboratory Page 1 of 11 TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the Korea Testing Laboratory. Tested and reported by Reviewed by Jeong-Min Kim , Senior Engineer Hee-Soo Kim , Telecommunication Team Manager KOREA TESTING LABORATORY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 http://www.ktl.re.kr Ref. Report No. 02-341-025-01 Name and address of the applicant Ace Security Inc. 4FL, Soo-il B/D, 793, Jung-dong, Wonmi-gu, Buchon-shi, Kyungki-do, Korea Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : August 26, 2002 Test item(s) ; Remote Control/ Security Device Transceiver (Transmitter Portion) (Car Alarm System / Remote) Model/type ref. ; MANNIX Manufacturer ; Ace Security Inc. Additional information ; -Required Authorization : Certification -FCC ID. : QLWSM700R -Note : Test report(Verification) of Receiver portion of this unit is issued on Ref. Report No. 02-341-025-02. Test date : September 17, 2002 Issue date : October 7, 2002 Ref. Report No. 02 - 341 – 025 - 01 Page 2 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 TABLE OF CONTENTS I. GENERAL INFORMATION 3 1. Grantee’s Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT 4 1. Labeling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) . RADIATED EMISSION MEASUREMENT (Section 15.231) 6 1. Test Procedure 2. Photograph of the test configuration 3. Sample Calculation 4. Measurement Data . OCCUPIED BANDWIDTH MEASUREMENT (Section 15.231) 10 . TEST EQUIPMENTS USED FOR MEASUREMENT 11 Ref. Report No. 02 - 341 – 025 - 01 Page 3 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . GENERAL INFORMATION 1. Grantee’s Name and : Ace Security Inc. Mailing Address 4FL, Soo-il B/D, 793, Jung-dong, Wonmi-gu, Buchon-shi, Kyungki-do, Korea 2. Manufacturer's Name and : Ace Security Inc. Mailing Address 4FL, Soo-il B/D, 793, Jung-dong, Wonmi-gu, Buchon-shi, Kyungki-do, Korea 3. Equipment Descriptions 3.1 Operating Frequency : 413.39 MHz 3.2 Type of Emission : Pulse Code Signal 3.3 Power Supply : DC 1.5 V(AAA size Battery) 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-1992 6. Place of Measurement : Absorber-lined Room (KTL) 7. Date of Measurement 7.1 Conducted Emission : Not Applicable 7.2 Radiated Emission : September 17, 2002 Ref. Report No. 02 - 341 – 025 - 01 Page 4 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . GENERAL REQUIREMENTS OF THE EUT 1. Labeling Requirement (Section 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1.1 Location of Label : User’s Guide Manual 1.2 How Applied : Printed 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 2 of the attached manual for details. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the installation of the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets ? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no Ref. Report No. 02 - 341 – 025 - 01 Page 5 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no Ref. Report No. 02 - 341 – 025 - 01 Page 6 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 . RADIATED EMISSION MEASUREMENT (Section 15.231) 1. Test Procedure 1.1 Preliminary Testing for Reference Preliminary testing was performed in a KTL absorber-lined room to determine the emission characteristics of the EUT. The EUT was placed on the wooden table which has dimensions of 0.8 meters in height, 1 meter in length and 1.5 meters in width. Receiving antenna (Biconical antenna : 30 to 300 MHz, Log-periodic antenna : 200 to 1000 MHz or Horn Antenna : 1 to 18 GHz) was placed at the distance of 1 meter from the EUT. An attempt was made to maximize the emission level with the various configurations of the EUT. Emission levels from the EUT with various configurations were examined on a spectrum analyzer connected with a RF amplifier and graphed by a plotter. …

Text truncated - open the document above for the full version.

Ref. Report No. 02 - 341 – 025 - 01 Page 8 of 11 Korea Testing Laboratory Telecommunication Team 222-13, Guro3-dong, Guro-gu, Seoul Korea 152-848 2. Photograph of the test configuration 3. Sample Calculation The emission level measured in decibels above one microvolt (dB) was converted into microvolt per meter (/m) as shown in following sample calculation. For example : Measured Value at 413.39 MHz 55.6 dB + Antenna Factor 15.7 dB/m + Cable Loss 3.9 dB Preamplifier 0.0 dB Distance Correction Factor * 0.0 dB ------------------------------------------------------------------------------------------- = Radiated Emission 75.2 dB/m ( = 5754.4 /m ) * Extrapolated from the measured distance to the specified distance by an inverse linear distance extrapolation.