QRTS-0704Dot Matrix Printer

® Quick Start GuideKurzanleitungGuide de démarrage rapideGuida di avvio rapidaGuía de instalaciónGuia Rápido de Inicialização 2440 2540 Matrix Printer QSG2440 _ en _ 396957 -. book Seite 1 Donnerstag , 22 . November 2007 11:31 11 This device fulfils the European standards requirem ents by complying with the Directive of the Com- mission dated May 3, 1989 (89/336/EEC) relating to electromagnetic compatibility and the Directive dated February 19, 1973 (73/23/EEC) relating to low-voltage electrical equipment. Conformity with the above mentioned Directives is indicated by the CE symbol attached to the device. Note: Conformity may be affected by:n using interface cables not complying with the specifications n non-observance of important instructions in the operator's manual n installing components not approved for this device by the manufacturer n unauthorized manipulation Dieses Gerät erfüllt die Anforderungen der Europäischen Normen durch Einhaltung der Richtlinie des Rates vom 3. Mai 1989 (89/336/EWG) bezüglich der Elektromagnetischen Verträglichkeit sowie die Richt-linie vom 19. Februar 1973 (73/23/EWG) bezüglich Elektrischer Betriebsmittel mit Niederspannungen. Die Konformität zu den oben angeführten Richtlinien ist durch das am Gerät angebrachte CE-Zeichen gekennzeichnet.Hinweis: Die Konformität kann beeinflußt werden durch: n Benutzung von nicht spezifizierten Schnittstellenkabeln n Nichtbeachtung wichtiger Hinweise der Bedienungsanleitung n Ersetzen von Bauteilen, die nicht vom Hersteller für dieses Gerät freigegeben wurden n Eingriffe durch Unbefugte Cet appareil remplit aux exigences des normes européennes en respectant la directive du Conseil du 3 mai 1989 (89/336/CE) relative à la compatibilité électromagnétique et la directive du 19février 1973 (73/23/CE) en matière du matériel à basse tension. La conformité aux directives mentionnées ci-dessus est repérée par la marque de conformité de la Communauté Européenne (CE). Remarque: La conformité peut être influencée par: n l'utilisation de câbles d'interface non spécifiés n le non-respect de consignes importantes du manuel d'utilisation n le remplacement de composants qui n'ont pas été homologués pour cet appareil par le constructeur n l'intervention de personnes non autorisées Questo apparecchio soddisfa le richieste delle norme europee rispettando la direttiva del consiglio del 3 Maggio 1989 (89/336/CEE) relativa alla compatibilità elettromagnetica nonché la direttiva del 19 Febbraio 1973 (73/23/CEE) relativa a mezzi di produzione elettrici a bassa tensione. La conformità alle direttive sopra citate è contrassegnata con il si mbolo CE applicato sull'apparecchio. Nota: La conformità può essere influenzata tramite: n Utilizzo di cavi interfaccia non specificati n Inosservanza di importanti indicazioni delle istruzioni per l'uso n Sostituzione di componenti per i quali non è stato dato il benestare dal produttore per questo apparecchio n Interventi tramite persone non autorizzate Este equipo corresponde a lo exigido en las normas europeas a base del cumplimiento de la directriz del Consejo del 3 de mayo de 1989 (89/336/CEE) en lo que se refiere a la compatibilidad electromagnética así como de la directriz del 19 de febrero de 1973 (73/23/CEE) en lo que se refiere a los materiales eléctricos con bajas tensiones. Para señalizar la conformidad con las directrices antes mencionadas, el equipo está dotado de la marca CE.Indicación: La conformidad puede estar influida por: n la utilización de cables de interface no especificados n la inobservancia de indicaciones importantes contenidas en el manual de servicio n la sustitución por componentes, que no han sido homologados por el fabricante para el equipo en cuestión n intervenciones de personas no autorizadas Important InformationThis equipment generates and uses radio frequency energy and if not in-stalled and used properly, that is, in accordance with the manufacturer's instructions, may cause interference in radio and television reception. It has been type tested and found to comply with the limits for class B com-puting devices in accordance with the specification in subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a partial installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is en-couraged to try to correct the interference by one or more of the following measures:n Reorient the receiving antenna, n Relocate the peripheral away from the receiver, n Move the peripheral away from the receiver n Plug the peripheral into a different outlet, so that the peripheral and re-ceiver are on different branch circuits If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the fol-lowing booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington DC 20402 Stock No. 004.000.00345.4.WARNING: To comply with FCC regulations on electromagnetic inter-ference for a class B computing device , the printer cable must be shiel- ded. To assure compliance with FCC regulations for a computing device, use a shielded interface cable with a metal shell connector. The use of cables not properly shielded may result in violating FCC regulations.This digital apparatus does not exceed the class B limits for radio noise emissions from digital apparatus as set out in the radio interference regu-lations of the Canadian department of communications.This unit complies with DOC standard C108.8-M 1983ATTENTION: Le présent appareil numérique n'ement pas de bruits radio-électriques déspassant les limites applicables aux appareils numér…

Text truncated - open the document above for the full version.

TOSHIBA TEC SINGAPORE PTE LTD 2 Ang Mo Kio Street 62, Singapore 569138 Reg. No. 04047/1988-Z



DECLARATION OF IDENTITY Date : 9 th Dec’07 Manufacturer : TOSHIBA TEC Singapore Pte Ltd Address : 2 Ang Mo Kio, Street 62, Singapore 569138. Declares, that There are no differences between the following Models except for model designation and minor differences in enclosure design not affecting the integrity of the safety. Product Name : Dot Matrix Printer Basic Model : 2540/24 Trade Name : TallyGenicom Product Name : Dot Matrix Printer Derived Model : 2440/24 Trade Name : TallyGenicom Product Name : Dot Matrix Printer Derived Model : 2540/9 Trade Name : TallyGenicom Product Name : Dot Matrix Printer Derived Model : 2440/9 Trade Name : TallyGenicom

Printer Overall Construction (Model : 2540/24)

24 Wire (PCB – Component Side) 24 Wire (PCB – Trace Side)