QS5-02WD3110DC Push Transmitter

Notice : (1) For FCC Caution: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. (2) For Industry Canada "Operation is subjects to the following two conditions:(1)this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device."

From: [email protected] Sent: Wednesday, January 22, 2003 10:16 PM To: [email protected] Subject: for FCC ID:QS5-02WD3110, AN03T2513 Dear Mike: I have do something for this project : QS5-02WD3110, AN03T2513, please changed them. Question #1 : Pls Change ID Label with Extend file. Question #2 : I have provide a Confidentiality letter in Extend file. Question #3 : User Manual has changed with new pdf file. Question #4 : We have been change the Description at section 1.1 in the test Report. ETC , Wen ----- Original Message ----- From: "Mike Kuo" <[email protected]> To: <[email protected]> Sent: Saturday, January 18, 2003 6:54 AM Subject: FW: Interquartz(Malaysia)Bhd.Representative Office, FCC ID:QS5-02WD3110, AN03T2513 > > > -----Original Message----- > From: CERTADM > Sent: Friday, January 17, 2003 2:50 PM > To: '[email protected]' > Subject: Interquartz(Malaysia)Bhd.Representative Office, FCC > ID:QS5-02WD3110, AN03T2513 > > > Notice_content > ------------- > Question #1: FCC ID number listed in the FCC ID label format does not match > with the proposed FCC ID number in the TCB application forma and test > report. Please confirm the correct FCC ID number and provide revised FCC ID > label format. > > Question #2: Confidentiality box is checked on the TCB application form. A > file named " confidential " did submit with the application. However, the > information contains in this file is Industry Canada application form. > Please provide revised request for confidentiality letter and list the > confidential document name. > > Question #3: User Manual does not contain information required under section > 15.21 of FCC rules. Please provide revised user manual to comply this > requirement. > > Question #4: Section 1.1 of test report, the product description does not > match with the EUT description. Please explain. > > Best Regards > > Mike Kuo > The items indicated above must be submitted before processing can continue > on the above referenced application. Failure to provide the requested > information within 60 days of the original e-mail date may result in > application dismissal and forfeiture of the filing fee. Also, please note > that partial responses increase processing time and should not be submitted. > Any questions about the content of this correspondence should be directed to > the e-mail address listed below the name of the sender.

ETC Report No.: ET91S-12-101-05Page A1 of A1 FCC ID: QS5-02WD3110 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Front view of EUT 2. Rear view of EUT

ETC Report No.: ET91S-12-101-05Page B1 of B2 FCC ID: QS5-02WD3110 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside 1 of EUT 2. Inside 2 of EUT ETC Report No.: ET91S-12-101-05Page B2 of B2 FCC ID: QS5-02WD3110 3. Front view of PCB 4. Front view of PCB

FCC ID.: QS5-02WD3110 Rev. No 1.0 FCC Part 15 Subpart C EMI TEST REPORT of E.U.T. : DC Push Transmitter FCC ID. : QS5-02WD3110 MODEL : WD-3110 Working Frequency : 433.92 MHz for APPLICANT: Interquartz (Malaysia) Bhd. Representative office ADDRESS: 5 th F1, No 16, Lane 130,Ming-Chun Road, Hsin Tien, Taipei Hsien, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 8, LANE 29, WEN-MING RD., LO-SHAN TSUN, KUI-SHAN HSIANG, TAOYUAN HSIEN 333, TAIWAN, R.O.C. Tel: (03) 3276170-3276174 Fax: (03) 3276188 Report Number: ET91S-12-101-05 ETC Report No.:ET91S-12-101-05FCC ID.: QS5-02WD3110 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant: Interquartz (Malaysia) Bhd. Representative office 5 th F1, No 16, Lane 130,Ming-Chun Road, Hsin Tien, Taipei Hsien, Taiwan Manufacturer: IQ Group Sdn. Bhd. 149 Jalan Sultan Azlan Shah, Taman Perindustrian Bayan Lepas, 11900 Pulau Pinang, Malaysia Description of EUT: a) Type of EUT: DC Push Transmitter b) Model No.: WD-3110 c) Serial No.: ---- d) FCC ID: QS5-02WD3110 e) Working Frequency: 433.92 MHz f) Power Supply: DC3V Battery Regulation Applied: FCC Rules and Regulations Part 15 Subpart C (2002) I HEREBY CERTIFY THAT; The data shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note:1.The results of the testing report relate only to the items tested. 2.The testing report shall not be reproduced except in full, without the written approval of ETC. 3.The report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Issue Date : Dec. 30, 2002 Test Engineer : Approve & Authorized Signer : Win-Po Tsai, Manager, NVLAP Signatory EMC Dept. of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No.:ET91S-12-101-05FCC ID.: QS5-02WD3110 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION............................................................................................................................................................1 1.1 PRODUCT DESCRIPTION...................................................................................................................................................................1 1.2 CHARACTERISTICS OF DEVICE:.......................................................................................................................................................1 1.3 TEST METHODOLOGY......................................................................................................................................................................1 1.4 TEST FACILITY..................................................................................................................................................................................1 2. DEFINITION AND LIMITS..............................................................................................................................................................2 2.1 DEFINITION........................................................................................................................................................................................2 2.2 RESTRICTED BANDS OF OPERATION.............................................................................................................................................2 2.3 LIMITATION.......................................................................................................................................................................................3 2.4 LABELING REQUIREMENT...............................................................................................................................................................4 2.5 USER INFORMATION.........................................................................................................................................................................4 3. RADIATED EMISSION MEASUREMENT....................................................................................................................................5 3.1 APPLICABLE STANDARD.................................................................................................................................................................5 3.2 MEASUREMENT PROCEDURE..........................................................................................................................................................5 3.3 TEST DATA.........................................................................................................................................................................................7 3.4 FIELD STRENGTH CALCULATION..................................................................................................................................................8 3.5 RADIATED TEST EQUIPMENT.........................................................................................................................................................8 3.6 MEASURING INSTRUMENT SETUP.................................................................................................................................................8 3.7 RADIATED MEASUREMENT PHOTOS.............................................................................................................................................9 4. BANDWIDTH OF EMISSION AND DUTY FACTOR..............................................................................................................12 4.1 APPLICABLE STANDARD PLOT GRAPHIC OF BANDWIDTH AND DUTY FACTOR...............................................................12 4.2 TEST EQUIPMENT...........................................................................................................................................................................12 4.3 ACTIVE TIME................................…

Text truncated - open the document above for the full version.

ETC Report No.:ET91S-12-101-05Sheet 1 of 1 Sheets FCC ID.: QS5-02WD3110 3.7 Radiated Measurement Photos