R5Q-LISAC200ACDMA 1xRTT Cellular Module

locate, communicate, ac c ele r a te LISA-C200 & FW75-C200 CDMA 1xRTT Wireless Modules System Integration Manual Abstract This document describes the features and the integration of u-blox LISA-C200 and FW75-C200 CDMA2000 1xRTT wireless modules. These modules are complete and cost efficient CDMA solutions offering 153 kb/s data speed dual-band 800/1900 MHz data transmission technology in compact form factors. www.u-blox.com LISA-C200&FW75-C200-System IntegrationManual CDMA-2X-11004-3 Page2of43 Document Information Title LISA-C200 & FW75-C200 Subtitle CDMA 1xRTT Wireless Modules Document type System Integration Manual Document number CDMA-2X-11004-3 Document status Preliminary Document status information Objective Specification Advance Information This document contains target values. Revised and supplementary data will be published later. This document contains data based on early testing. Revised and supplementary data will be published later. Preliminary This document contains data from product verification. Revised and supplementary data may be published later. Released This document contains the final product specification. This document applies to the following products: Name Type number Firmware version PCN / IN LISA-C200 LISA-C200-01S E0.S.03.00.10R UBX-TN-12041 LISA-C200 LISA-C200-21S E0.V.03.00.02R UBX-TN-12041 FW75-C200 FW-C200-01S E0.S.03.00.10R UBX-TN-12041 FW75-C200 FW-C200-21S E0.V.03.00.02R UBX-TN-12041 This document and the use of any information contained therein, is subject to the acceptance of the u-blox terms and conditions. They can be downloaded from www.u-blox.com. u-blox makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to mak e changes to specifications and product descriptions at any time without notice. u-blox reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © 2012, u-blox AG. u-blox ® is a registered trademark of u-blox Holding AG in the EU and other countries. LISA-C200&FW75-C200-System IntegrationManual CDMA-2X-11004-3 Preliminary Preface Page 3 of 43 Preface u-blox Technical Documentation As part of our commitment to customer support, u-blox maintains an extensive volume of technical documentation for our products. In addition to our product-specific technical data sheets, the following manuals are available to assist u-blox customers in product design and development. AT Commands Manual: This document provides the description of the supported AT commands by the LISA-C200 & FW75-C200 module to verify all implemented functionalities. System Integration Manual: This Manual provides hardware design instructions and information on how to set up production and final product tests. Application Note: document provides general design instructions and information that applies to all u-blox Wireless modules. See Section Related documents for a list of Application Notes related to your Wireless Module. How to use this Manual The LISA-C200 & FW75-C200 System Integration Manual provides the necessary information to successfully design in and configure these u-blox wireless modules. This manual has a modular structure. It is not necessary to read it from the beginning to the end. The following symbols are used to highlight important information within the manual: An index finger points out key information pertaining to module integration and performance. A warning symbol indicates actions that could negatively impact or damage the module. Questions. If you have any questions about u-blox Wireless Integration, please: Read this manual carefully. Contact our information service on the homepage http://www.u-blox.com Read the questions and answers on our FAQ database on the homepage http://www.u-blox.com Technical Support Worldwide Web Our website (www.u-blox.com) is a rich pool of information. Product information, technical documents and helpful FAQ can be accessed 24h a day. By E-mail Contact the nearest Technical Support office by email. Use our service pool email addresses rather than any pe rsonal email address of our staff. This makes sure that your request is processed as soon as possible. You will find the contact details at the end of the document. Helpful Information when Contacting Technical Support When contacting Technical Support please have the following information ready: Module type (e.g. LISA-C200) and firmware version Module configuration Clear description of your question or the problem A short description of the application Your complete contact details LISA-C200&FW75-C200-System IntegrationManual CDMA-2X-11004-3 Preliminary Contents Page 4 of 43 Contents Preface ................................................................................................................................3 Contents..............................................................................................................................4 1 System description .......................................................................................................6 1.1 Overview .............................................................................................................................................. 6 1.2 Architecture.......................................................................................................................................... 7 1.2.1 Functional blocks........................................................................................................................... 7 1.3 Pin description ...................................................................................................................................... 8 1.4 Power management ........................................................................................................................... 10 1.4.1 Power supply circuit overview .....................…

Text truncated - open the document above for the full version.

12626 High Bluff Drive, Suite 200 San Diego, CA 92130 November 26, 2012 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: R5Q‐LISAC200A Authority to Act as Agent On our behalf, I appoint Alan Laudani of Nemko USA Inc., 2210 Faraday Ave, STE 150, Carlsbad, CA, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Fusion Wireless, Inc. with offices at 12626 High Bluff Drive, Suite 200, San Diego, CA 92130. This appointment is in effect until April 1, 2013. Jake Bascon Certification Engineer

12626 High Bluff Drive, Suite 200 San Diego, CA 92130 November 26, 2012 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: R5Q‐LISAC200A Pursuant to Sections 0.457(d)(I)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying as outlined below: Schematics, Parts List, Operating Description, Block Diagrams The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(I)(ii), disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. Jake Bascon Certification Engineer

Page 1 of 2 12626 High Bluff Drive, Suite 200 Dec 10, 2012 San Diego, CA 92130 Nemko 2210 Faraday Ave, Suite 150 Carlsbad, CA 92008 USA Attn: Reviewing Engineer RE: PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL To Whom It May Concern: We, Fusion Wireless, hereby requests approval of our device for licensed Modular Transmitters Subject to the Licensed Radio Services Rules, described as follows: Brand name: Fusion Wireless Model # LISA-C200 FCC ID: R5Q-LISAC200A In FCC 15.212 lists additional guidelines our device complies with: 1. The modular transmitter must have its own shielding. The DUT does provide RF shielding. Please refer to DUT picture. 2. The modular transmitter must have buffered modulation/data inputs The DUT has buffered data input it’s integrated chip. . 3. The modular transmitter must have its own power supply regulation The DUT has its own power supply regulation it’s integrated in PMIC chip 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204 b and c The DUT does meet the FCC antenna requirements; SMD antenna connector provided on board. Please refer to picture. 5. The modular transmitter must be tested in a stand-alone configuration The DUT was tested in a stand-alone configuration via a test kit. Please see section photographs of test configuration in the test report. 6. The modular transmitter must be labelled with its own FCC ID number Please see exhibition label sample for the FCC ID of this module. Page 2 of 2 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The DUT is compliant with all applicable FCC rules. 8. The modular transmitter must comply with any applicable RF exposure requirements. The DUT is compliant with RF exposure requirement MPE evaluation. The MPE report is addressed in the RF exposure exhibition. Sincerely, Jake Bascon Certification Engineer u-blox San Diego, Inc.

Evaluation of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01where: S = power density P = power input to the antennaG = power gain of the antenna in the direction of interest relative to an isotropic radiatorR = distance to the center of radiation of the antenna Maximum peak output power --Conducted 24.61 dBm 23.69 dBm 0.289 (W) 0.234 (W) Antenna gain(typical): 2.00 (dBi) 2.50 (dBi) Maximum antenna gain: 1.58 (numeric) 1.78 (numeric) Evaluation distance: 20.00 (cm) 20.00 (cm) Evaluation frequency: 836.52 (MHz) 1851.25 (MHz) Limit from table below: 0.558 (mW/cm^2) 1 (mW/cm^2) Power density at Evaluation frequency: 0.091 (mW/cm^2) 0.083 (mW/cm^2) EUT complies FCC/LSGAC Local Official’s Guide to RFA LOCAL GOVERNMENT OFFICIAL'S GUIDE TO TRANSMITTING ANTENNA RFEMISSION SAFETY: RULES, PROCEDURES, AND PRACTICAL GUIDANCE 2 4 R PG S  

Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 CERTIFICATION TEST REPORT Applicant: U-Blox 12626 High Bluff Drive, Suite 200 San Diego, CA 92130 Equipment Under Test (EUT): CDMA 1xRTT Module Model: LISA-C200 FCC ID: R5Q-LISAC200A IC ID: 8595B-LISAC200A In Accordance With: FCC Part 22, Subpart H RSS-132, Issue 2 September 2005 FCC Part 24 Subpart E RSS 133 Issue 5 February 2009 RSS GEN Issue 3 December 2010 Tested By: Nemko USA Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Date: December 7, 2012 Report Number: 2012 12225324 FCC Project Number: 10234402 Nex Number: 225324 Total Number of Pages: 53 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: R5Q-LISAC200A Report Number: 2012 12225324 FCC IC: 8585B-LISAC200A Page 2 of 53 Section 1: Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC rules parts CFR47 Part 2 and 24 subpart E for the United States and RSS132 Issue 2, RSS133 Issue 5, and RSS-Gen Issue 3 for Canada. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC and IC. The assessment summary is as follows: Apparatus Assessed: CDMA 1xRTT Module Model: LISA-C200 Serial: A10000157C0792 Specifications: FCC Part 22, Subpart H Industry Canada RSS-132, Issue 2, September 2005 FCC Part 2, Part 24 Subpart E RSS 133 Issue 5, February 2009 RSS-GEN Issue 3 December 2010 Date Received in Laboratory: November 27, 2012 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: R5Q-LISAC200A Report Number: 2012 12225324 FCC IC: 8585B-LISAC200A Page 3 of 53 1.1 Report Release History REVISION DATE COMMENTS - DECEMBER 7, 2012 Prepared By: Andreas Gillmeier - DECEMBER 7, 2012 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. TESTED BY: Date: DECEMBER 7, 2012 Andreas Gillmeier, Sr. EMC Wireless Engineer RELEASED BY: Date: December 10, 2012 Alan Laudani, Test Report Verificator Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: R5Q-LISAC200A Report Number: 2012 12225324 FCC IC: 8585B-LISAC200A Page 4 of 53 TABLE OF CONTENTS Section 1: Summary of Test Results ............................................................................... 2 1.1 Report Release History ..................................................................................... 3 Section 2: Equipment Under Test ................................................................................... 5 2.1 Product Identification ........................................................................................ 5 2.2 Technical Specifications of the EUT ................................................................. 5 Section 3: Test Conditions .............................................................................................. 6 3.1 Test Environment ............................................................................................. 6 3.2 Test Equipment ................................................................................................ 6 Section 4: Observations .................................................................................................. 7 4.1 Modifications Performed During Assessment ................................................... 7 4.2 Record Of Technical Judgments ...................................................................... 7 4.3 EUT Parameters Affecting Compliance ............................................................ 7 4.4 Test Deleted ..................................................................................................... 7 4.5 Additional Observations .................................................................................... 7 Section 5: Results Summary ........................................................................................... 8 5.1 Test Result summary table ............................................................................... 8 Appendix A: Test Results ................................................................................................ 9 A1. Powerline conducted emissions ............................................................................ 9 A2. RF Power Output ................................................................................................ 18 A3. Occupied Bandwidth ........................................................................................... 25 A4. Spurious Emissions At Antenna Terminals ......................................................... 33 A5. Field strength of Spurious Emissions .................................................................. 40 A6. Receiver Spurious ............................................................................................... 49 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760…

Text truncated - open the document above for the full version.

Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 1 Conducted emissions on AC power line test setup Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 2 Conducted Spurious Emission on antenna port test setup Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 3 Conducted power test setup Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 4 Band edge and occupied bandwidth test setup Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 5 Frequency Stability set up Nemko USA, Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Phone: (760) 444‐3500 Fax: (760) 444‐3005 6 Radiated Field Strength Spurious Emission Test Setup 7 Radiated Field Strength Spurious Emission Test Setup