R5S-4200FFM4200F

Fluidmesh 4200 FIBER Installation and Configuration Manual Edition 1.6 (Firmware V8.3) Table of Contents 1. HAZARDOUS CONDITION WARNINGS ........................................................... 6 1.1. Water Ingress Hazard ............................................................................. 6 1.2. Radio-Frequency Transmission Hazard .................................................... 7 1.3. Optical Radiation Hazard ........................................................................ 8 1.4. Hot Surfaces Hazard ............................................................................... 9 2. Reporting Mistakes And Recommending Improvements ................................... 10 3. Getting Started ............................................................................................... 11 3.1. Introduction ........................................................................................... 11 3.1.1. Fluidmesh 4200 FIBER ................................................................. 11 The Fluidmesh 4200 FIBER Radio Transceiver .................................. 11 Introduction ..................................................................................... 11 Unit Function And Throughput Speed ............................................... 12 Data Throttling ................................................................................ 12 MPLS Protocol ................................................................................ 12 Unit Configuration ........................................................................... 12 Role Adaptability ............................................................................. 12 Environmental Rating ...................................................................... 13 Product Specifications ..................................................................... 13 Transceiver And Gateway Unit Power Consumption .......................... 13 3.2. Fluidmesh Architecture ......................................................................... 14 3.2.1. Overview ..................................................................................... 14 Wireless Network Architectures ........................................................ 14 The FluidMAX TDMA Protocol ......................................................... 14 3.2.2. Fluidmesh Technologies ............................................................... 15 Prodigy .......................................................................................... 15 RACER .......................................................................................... 16 3.2.3. Point-To-Point Wireless Bridge ...................................................... 16 3.2.4. Mesh Network Architecture ........................................................... 17 3.2.5. Point-To-Multipoint Architecture With FluidMAX .............................. 18 3.3. Fluidmesh Network Addressing ............................................................. 20 3.3.1. Bridge IP Addressing ................................................................... 20 3.3.2. Unit Identification And Addressing ................................................. 20 Mesh- And Bridge-Capable Radio Transceiver Identification ............... 20 Operating The Unit In Mesh Point Mode Or Mesh End Mode .............. 21 Network Addressing ........................................................................ 22 Fluidmesh Radio Transceivers ................................................... 22 Connecting And Configuring An Ethernet Edge Device ...................... 23 Fluidmesh Radio Transceivers ................................................... 23 4. Hardware Installation ..................................................................................... 24 4.1. Fluidmesh Hardware Installation ............................................................ 24 4.1.1. Installing The Fluidmesh 4200 FIBER ............................................ 24 Environmental Rating And Unit Roles ............................................... 24 Installation Hardware ....................................................................... 24 4.1.2. Fluidmesh 4200 FIBER Status And Link LEDs ............................... 24 Unit And Link Quality Status ............................................................ 24 Boot Sequence ............................................................................... 25 4.1.3. Supplying Power To The Fluidmesh 4200 FIBER ............................ 25 Connecting Power To The Fluidmesh 4200 FIBER ............................. 26 DC IN, LAN And Fiber-Optic Ports .............................................. 26 4.1.4. Rebooting The Firmware And Resetting The Unit To Factory Defaults ............................................................................................... 27 Fluidmesh 4200 FIBER © Fluidmesh Networks LLCPage 2 of 180 Device Firmware Reboot ................................................................. 27 Resetting The Unit To Factory Settings ............................................. 28 4.1.5. Suitability For Outdoor Installation ................................................. 28 4.2. Connecting The Fluidmesh Fluidmesh 4200 FIBER To A Network And Antennas .................................................................................................... 29 4.2.1. Terminal Assignments For Power And Data Connectors .................. 29 M12 A-Coded ................................................................................. 29 M12 A-Coded (Five-Pin) ............................................................ 29 M12 A-Coded Eight-Pin (Pre-September 2016 Only) ................... 30 M12 X-Coded ................................................................................. 32 XCO / SFP ..................................................................................... 33 Connecting Fiber-Optic Connectors To SFP Modules ........…

Text truncated - open the document above for the full version.

Date: 2020/6/12 DTS-UNII Device Declaration Letter To whom it may concern, we declare below featured for equipment authorization regarding FCC ID: R5S-4200F (1)DFS Device --☐Master,☐Client with Radar detection capability,☐Client without radar detection capability,☒N/A (2)Active / Passive Scanning Frequency Band(MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode or WIFI Direct capability Access point capability Non Applicable 2412 - 2462MHz ☐Yes ,☐No☐Yes ,☐No ☐Yes ,☐No☐Yes ,☐No ☒ 5150 - 5250MHz ☐Yes ,☐No☐Yes ,☐No ☐Yes ,☐No☐Yes ,☐No ☒ 5250 - 5350MHz ☐Yes ,☐No☐Yes ,☐No ☐Yes ,☐No☐Yes ,☐No ☒ 5470 - 5725MHz ☐Yes ,☐No☐Yes ,☐No ☐Yes ,☐No☐Yes ,☐No ☒ 5725 - 5850MHz ☒Yes ,☐No☐Yes ,☒No ☒Yes ,☐No☒Yes ,☐No ☐ (3)Country code selection ability -☒Yes ,☐No If yes, pls explain how it was implemented :Country code is factory set in the UI and cannot be changed by end users. (4)Meet 15.202 requirement -☒Yes ,☐No pls check below : ☒A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices. ☐A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5)For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. ☒Apply, “Yes, please see SW security Description”. ☐Not apply,(If apply, please help to provide explanation on it was implement, and how software was controlled) Signature: Name (Printed): Giancarlo Semino Title: HARDWARE ENGINEER On behalf of Company: Fluidmesh Networks LLC Telephone: +39.02.0061.6189 Address:81 Prospect St., Brooklyn, New York, United States 11201

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Fluidmesh Networks LLC Address 81 Prospect St., Brooklyn, New York, United States 11201 Grantee Code R5S FCC ID R5S-4200F Authorized Contact Name Giancarlo Semino Contact Email [email protected] Contact Phone +39.02.0061.6189 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicantshallmake provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicantshall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs:https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs:https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100:https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:Jun. 06, 2020 Print Name: Giancarlo Semino Title: HARDWARE ENGINEER *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Date:June 5 th 2020 TO:Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: R5S-4200F To whom it may concern: We, the undersigned, hereby authorize SGS Taiwan Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Fluidmesh Networks LLC. This authorization is valid until further written notice from the applicant. Name(Printed):Giancarlo SeminoTitle: HARDWARE ENGINEER Signature: On behalf of Company: Fluidmesh Networks LLC Telephone: +39.02.0061.6189

To:SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Fluidmesh Networks LLC 81 Prospect St. Brooklyn, New York, United States 11201 Regarding:Confidentiality Request regarding application for FCC ID:R5S-4200F LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Delete any document that is NOT included in your application Schematic(s) Block Diagrams The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Delete any document that is NOT included in your application External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code):Giancarlo Semino Title: HARDWARE ENGINEER

EUT Photo No.: ER/2020/30118~119-P Page: 1 of 4 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group EXTERNAL PHOTOGRAPHS OF EUT All View of EUT Front View of EUT EUT Photo No.: ER/2020/30118~119-P Page: 2 of 4 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Back View of EUT Side View of EUT – 1 EUT Photo No.: ER/2020/30118~119-P Page: 3 of 4 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Side View of EUT – 2 Side View of EUT – 3 EUT Photo No.: ER/2020/30118~119-P Page: 4 of 4 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. A…

Text truncated - open the document above for the full version.

Label location The label stick on the back side.

EUT Photo No.: ER/2020/30118~119-P Page: 1 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group INTERNAL PHOTOGRAPHS OF EUT Open View of EUT – 1 Open View of EUT –2 EUT Photo No.: ER/2020/30118~119-P Page: 2 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Open View of EUT –3 Internal View of EUT –1 EUT Photo No.: ER/2020/30118~119-P Page: 3 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Internal View of EUT –2 Internal View of EUT –3 EUT Photo No.: ER/2020/30118~119-P Page: 4 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approva…

Text truncated - open the document above for the full version.

Report No: ER/2020/30119 Page: 1 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group RF EXPOSURE REPORT OF Applicant:Fluidmesh Networks LLC 81 Prospect Street Brooklyn NY 11201 USA Product Name:FM4200F Brand Name:Fluidmesh FM4200F Model No.:FM4200F Model Difference:N/A Report Number:ER/2020/30119 FCC ID:R5S-4200F FCC Rule PartPart 2.1091 Issue Date:Jun. 01, 2020 We hereby certify that: The above equipment was verified by SGS Taiwan Ltd. The evaluation in this report is in compliance with the above rule(s). The results of this report relate only to the sample identified in this report. Approved By: Yeh John/ Asst.Manager Report No: ER/2020/30119 Page: 2 of 7 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90 天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd.No.134,Wu Kung Road, New Taipei Industrial Park, Wuku District, New Taipei City, Taiwan/新北市五股區新北產業園區五工路134 號 台灣檢驗科技股份有限公司t (886-2) 2299-3279f (886-2) 2298-0488www.sgs.com.tw Member of SGS Group Revision History Report NumberRevisionDescriptionIssue DateRemark ER/2020/30…

Text truncated - open the document above for the full version.