RDY-305NElite Super Selective Cat Flap

ENGLISH DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS IMPORTANT - READ BEFORE USE FITTING INSTRUCTIONS WICHTIG - BITTE VOR VERWENDUNG LESEN EINBAUANLEITUNG IMPORTANT - À LIRE AVANT USAGE INSTRUCTIONS DE MONTAGE IMPORTANTE - LEA ANTES DE USAR INSTRUCCIONES DE INSTALACIÓN BELANGRIJK! DIT EERST LEZEN VOOR GEBRUIK MONTAGE INSTRUCTIES CAT MATEElite ® NL E F D CAT FLAP · KATZENKLAPPE · CHATIÈRE · GATERA · KATTENDEUR ©PET MATE Ltd· Lyon Road · Hersham · Surrey · KT12 3PU · England N.America only: Ani Mate· 104A Longview Drive · Conroe · Texas 77301 www.pet-mate.com 30512/0312 Ref: 305N · 306 · 307 · 355 · 356 www.pet-mate.com +44 (0)1932 700 001 N America (936) 760 4333 30512-0312 instructions.qxd 9/3/12 14:42 Page 1 ENGLISH DEUTSCH FRANÇAIS ESPAÑOL NEDERLANDS 3 2 12 56 910 34 7 1112 8 150mm (6”) 3mm ( 1 /8”) t A 30512-0312 instructions.qxd 9/3/12 14:42 Page 3 ENGLISH 4 2.3 The black foam seal is not suitable for fitting to glass and should be removed. If desired, the exterior frame may be sealed to the glass panel using silicone sealant. 2.4 Position interior frame on inside of door, screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps. 3. Wall Fitting If you are installing your cat flap in a wall, you will need to purchase Elite wall liners. You will need 1 wall liner for every 50mm (2") of wall thickness over 50mm (2") or 100mm (4”) for ‘Chip & Disc’ (Ref. 355/356) cat flaps. 3.1 Create a rectangular hole in your wall 205mm (8") high by 180mm (7") wide. 3.2 Remove interior frame battery cover by pushing up as shown, (Fig. 7). 4 Way Locking Cat Flap (Ref. 307) only:Remove the 4-way knob as shown in Fig. 12 using a thin screwdriver to lever off cover (A) as shown. 3.3 Remove interior frame cover by unscrewing 2 screws in rear of interior frame (Fig. 8). (Note: these screws may be discarded as it will be impossible to refit them). Next remove the 2 screws under the battery cover and remove the interior frame by pivoting down (Fig. 9). 3.4Carefully remove 2 screw clips with pliers. (Fig. 10). 3.5Fit interior frame assembled with requisite number of wall liners to interior wall securing in position with 2 suitable screws as shown in Fig. 11. (Note: you will need to fit a washer (not supplied) under the head of the screws). If required, the wall liners may be glued in place, although a firmpush fit will usually suffice. 3.6 Refit interior frame cover with 2 screws under battery cover, taking great care not to trap electrical wires. (Refit the 4-way knob for 4 Way Locking Cat Flapusing a hand screwdriver.) Replace the battery cover. 3.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit 2 screw caps. IMPORTANT: • BEFORE INSTALLATION, PROGRAM CAT FLAP AS DESCRIBED IN OPERATION INSTRUCTIONS • DO NOT CUT TUNNEL OF CAT FLAPS. 1. Wood / Plastic / Metal Door Panels 1.1 Place exterior frame in desired position on door and draw around the aperture. We recommend the bottom of the aperture is approximately 150mm (6") above ground level. (Fig.1). If you must fit higher consider providing a step to help your cat enter. 1.2 Use an electric jigsaw to cut 3mm (1/8") OUTSIDE of drawn line. (Fig. 2). Be careful to cut hole square to the door, particularly with thicker doors. Ensure interior frame is free fitting in hole. 1.3 Determine thickness of door panel, (t). (Fig. 3). 1.4 Holding the interior frame and the exterior frame in position, mark the 2 screw holes. (Fig. 4). 1.5 Remove the frames and drill screw clearance holes in panel to 6mm (1/4") diameter. (Fig. 5). 1.6 Position interior frame on inside of door and screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps. 1.7 For metal panels you must remove batteries for a minimum of 2 minutes after installation. This will enable the cat flap to retune itself to its new location for maximum performance. 2.Glass Panels 0-50mm (0-2") Thick 2.1 We recommend that you ask a glazier to cut a hole of 229mm (9") diameter in the position required and then install the cat flap as detailed below. Alternatively, you may prefer to replace the glass panel with a clear plastic panel and install as instructions 1.1 to 1.6. Note: It is not possible to cut a hole in double glazed or toughened glass. You will need a new panel with the hole already cut from your glazier. 2.2Determine thickness of door panel, (t). (Fig. 3). ENGLISH 5 30512-0312 instructions.qxd 9/3/12 14:42 Page 5 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Pet Mate Ltd Add: Lyon Road, Hersham, Surrey, KT12 3PU Tel: +44 (0)1932 700 000 Fax: +44 (0)1932 700 002 2012-12-14 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: RDY-305N We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description - BOM List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Steve Brooks / Manager Contact information / address : Lyon Road, Hersham, Surrey, KT12 3PU Tel: +44 (0)1932 700 000 Fax: +44 (0)1932 700 002 E-Mail: [email protected]

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.:LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.:LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.:LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.:LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7 Fig.8

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: RDY-305N Report No.: LCS121029102QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Label Location (Size: L 47.2 mm x 37.5mm) Material: Tagboard Glue: adhesive sticker Font color: White Label color: Black Pet Mate Ltd Model: 305N FCC ID: RDY-305N This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.: LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 Antenna Battery Slot SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.: LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.: LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. ID: RDY-305N Report No.:LCS121029102QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 16 FCC TEST REPORT FOR Pet Mate Ltd Elite Super Selective Cat Flap Model No.:305N Prepared for : Pet Mate Ltd Address : Lyon Road, Hersham, Surrey, KT12 3PU Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1F., Xingyuan Industrial Park, Tongda Road, Bao’an Blvd., Bao’an District, Shenzhen, Guangdong, China Date of receipt of test sample : November 01, 2012 Number of tested samples : 1 Serial number : Prototype Date of Test : November 01, 2012 –December 14, 2012 Date of Report : December 14, 2012 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. ID: RDY-305N Report No.:LCS121029102QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 16 FCC TEST REPORT FCC CFR 47 PART 15 C (15.209) Report Reference No. ............... : LCS121029102QF Date of Issue ................................. : December 14, 2012 Testing Laboratory Name.......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ......................................... : 1F., Xingyuan Industrial Park, Tongda Road, Bao’an Blvd., Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : Pet Mate Ltd Address ......................................... : Lyon Road, Hersham, Surrey, KT12 3PU Test Specification Standard ........................................ : FCC CFR 47 PART 15 C (15.209) Test Report Form No. ................... : LCSEMC-1.0 TRF Originator ............................. : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF................................... : Dated 2011-03 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ................ : Elite Super Selective Cat Flap Trade Mark ................................... : N/A Model/ Type reference ................. : 305N Ratings .......................................... : DC 6.0V by 4*AA batteries Result .......................................... : Positive Compiled by: Supervised by: Approved by: Yoyo Wang/ File administrators Vito Cao/ Technique principalGavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. ID: RDY-305N Report No.:LCS121029102QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 16 FCC -- TEST REPORT Test Result: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS121029102QF December 14, 2012 Date of issue Type / Model........................... : 305N EUT......................................... : Elite Super Selective Cat Flap Applicant............................... : Pet Mate Ltd Address.................................. : Lyon Road, Hersham, Surrey, KT12 3PU Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Pet Mate Ltd Address................................... : Lyon Road, Hersham, Surrey, KT12 3PU Telephone............................... : / Fax.......................................... : / Factory................................... : Pet Mate Ltd Address................................... : Lyon Road, Hersham, Surrey, KT12 3PU Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. ID: RDY-305N Report No.:LCS121029102QF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 16 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION ....................................................................................................... 5 1.1 Description of Device (EUT).................................................................................................................. 5 1.2 Host System Configuration List and Details .......................................................................................... 5 1.3 External I/O Cable .................................................................................................................................. 5 1.4 Description of Test Facility .................................................................................................................... 5 1.5 Statement of The Measurement Uncertainty .......................................................................................... 6 1.6 Measurement Uncertainty....................................................................................................................... 6 1.7 Description Of Test Modes..................................................................................................................... 6 1.8 Summary Of Test Result......................................................................................................................... 6 2. TEST METHODOLOGY .............................................................................................................7 2.1 EUT Configura…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: RDY-305N Report No.: LCS121029102QF ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 1. TEST SETUP PHOTOGRAPHS Fig: 1 Fig: 2