REP-3100-1HotPoint Wireless Mesh Node

i User Manual HotPort 3100 Indoor Wireless Mesh Node wireless instant networks™ HotPort 3103 Indoor Wireless Mesh Node ii User Manual HotPort 3100 Indoor Wireless Mesh Node Copyright Notice © 2003-2005 Firetide, Inc. All rights reserved. Trademarks Firetide, the Firetide logo, Instant Mesh Networks, HotPort, and HotView are trademarks of Firetide, Inc. All other trademarks are the property of their respective owners. User Manual iii HotPort Limited End User Product Warranty Pursuant to all provisions described herein, Firetide products are warranted for one (1) year from the date of purchase against defects in the build materials and workmanship. Firetide also warrants that the Software will materially conform to the documentation supplied by Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is notified in writing of such failure within the warranty period, Firetide or its reseller shall use commercially reasonable efforts to promptly correct the nonconformity. Firetide does not warrant that the use of the Software will be uninterrupted or error free. Firetide does not warrant that the Products will meet any requirements or specifications of any End User Customer. This warranty applies to the entire Firetide product, including antennas and the AC power adapter. The above warranties are void if the alleged defect cannot be verified by Firetide or if, as determined by Firetide, the product failure was due to tampering, abuse, misuse, accident, shipping, handling, or storage; or if the product has been installed, used, or maintained in a manner not described in the product user manual, if the product has been altered In any way, or If product serialization has been altered. Any attempt to disassemble or repair the product by anyone other than Firetide immediately voids this warranty. This warranty applies only to the original End User purchaser of the product and may not be transferred to any other individual or entity. THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS LIMITATION MAY NOT APPLY TO YOU. In no event will Firetide be liable for any special, incidental, consequential, punitive or indirect damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use the product or the performance, interruption or failure of the product, irrespective of the cause of action, even if Firetide has been advised of the possibility of such damages. Firetide's cumulative liability for all claims arising out of or in connection with this warranty will not exceed the amount paid by the original End User purchaser to purchase the product. The amounts payable for the product are based in part on these limitations and these limitations shall apply not-withstanding the failure of essential purpose of any remedy. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so to that extent the above limitations or exclusions may not apply to you. By using the product the original End User purchaser agrees to and is bound by these terms and conditions. In the event that a product fails to meet this warranty and Firetide’s authorized reseller is notified in writing of such failure within the warranty period, Firetide shall, at its own discretion, either repair the product or replace it with the same or a functionally-equivalent product free of charge. Replacement products may contain refurbished materials in whole or in part. Firetide will honor this warranty provided the product is returned through an authorized Firetide reseller or dealer with shipping charges prepaid, along with a proof of purchase describing the original purchase date and product serial numbers if applicable. The authorized reseller must acquire a Return Materials Authorization (RMA) number from Firetide prior to returning any product. Firetide does not accept shipments of defective products without shipping charges prepaid. HotPort 3103 Indoor Wireless Mesh Node iv Explanation of Graphical Symbols This symbol is intended to alert the user to the presence of important operating, maintenance, and servicing instructions in the literature accompanying this unit. Failing to comply with this instruction may result in electrical shock. This symbol is intended to alert the user to the presence of important operating, maintenance, and servicing instructions in the literature accompanying this unit. Failing to comply with this instruction may result in a hazard. DO NOT OPEN THE COVER • Dangerous voltages inside. • No serviceable parts inside. • Refer to qualified service personnel. • Unit must be disconnected from power prior to servicing. • Unit has tamper-evident labeling that indicates when cover has been removed. v Table of Contents FIRETIDE™ HOTPORT™ 3103 INDOOR WIRELESS MESH NODE.........................................................................1 FIRETIDE HIGH-PERFORMANCE MESH NETWORK...................................................................................................1 WHAT IS A FIRETIDE MESH NETWORK?....................................................................................................................1 CONFIGURING THE MESH.............................................................................................................................................2 SECURITY....................................................................................................…

Text truncated - open the document above for the full version.

Exclusive Certification Corp. 4F-2, No. 28, Lane 78, Xing-Ai Rd. Nei-hu , Taipei City 114 Taiwan R.O.C 11478284-2F Tel: 886-2-2792-3366 Fax: 886-2-2792-1100 To whom it may concern: The enclosed documents constitute a formal submittal and application for a Grant of Equipment Autho rization pursuant to Subpart C+E of Part 15 of FCC rules (CF R47) regarding HotPort Wireless Mesh Node Module for the Firetide Inc. model 3100. Data within this report demonstrates that the equipment tested complied with the FCC limits for intentional radiators. Exclusive Certificate Corp. (ECC), as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is enclosed. If there are any questions or if further information is needed, please contact ECC for assistance. Ivy Chen TEL: +886-2-2792-3366 # 204 FAX: +886-2-2792-1100 E-mail: [email protected]

External Photos

HotPort Wireless Mesh Node This device complies with Part 15 of FCC Rule. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation. tested to comply with FCC Standards FOR HOME OR OFFICE USE 0560 O FCC ID: REP-3100-1 004XXXXXXX 004XXXXXXX Firetide Model: 3100 Serial Number Radio MAC Address No User serviceable parts inside. Warranty void if opened. Firetide, Inc., Made in Taiwan. SIZE: 544*100 mm Canada ID: 4988A-31001 RF Module Inside Complies with RSS-210

Internal Photos

3100 Operational Principle This project uses the Brecis MSP2007 CPU the processor and it offers a memory configuration of 4M bytes Flash and 256M bytes SDRAM. This device supports 10/100 Base-TX LAN network interfaces using Davicom DM9161 as the PHY controller. The interface to the LAN network is through an RJ45 STP port. A parallel port is available with I/O transmission by AT7601F. USB print port uses NEC uPD720101 host controller, which fully compliant USB specification 2.0. WE support one USB ports. Using WLAN module using mini PCI wireless module. There are 4 bi-color LEDs. All control by firmware. This device derives its power from a 12V DC @ 1A power adapter which needs to be converted to 1.8V, 3.3V and 5V DC.

1.1. Test Result of RF Exposure Evaluation . Product: HotPort Wireless Mesh Node . Test Item: RF Exposure Evaluation Data . Test site: OATSI-SD . Test Mode: Normal Operation 1.1.1. Antenna Gain The maximum Gain is 4.0 dBi. 1.1.2. EUT Operation condition Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 1.1.3. Output Power into Antenna & RF Exposure Evaluation Distance Frequency Range: 5.15-5.35 GHz Test Date: Feb. 17, 2005 Temperature: 23 Humidity: 69 Transmit Rate: 6Mbps Atmospheric pressure: 1028mmHg Channel Channel Frequency (MHz) Output Power to Antenna (dBm) Power Density (S) (mW/cm 2 ) 01 5180 15.77 0.0190 04 5240 15.83 0.0190 05 5260 15.88 0.0190 08 5320 15.93 0.0200 Frequency Range: 5.725-5.850 GHz Test Date: Feb. 17, 2005 Temperature: 23 Humidity: 69 Transmit Rate: 6Mbps Atmospheric pressure: 1028mmHg Channel Channel Frequency (MHz) Output Power to Antenna (dBm) Power Density (S) (mW/cm 2 ) 03 5745 18.45 0.0350 11 5785 17.72 0.0300 13 5825 17.18 0.0260 The MPE is calculated as 0.350 mW / cm 2 < limit 1 mW / cm 2 . So, RF exposure limit warning or SAR test are not required.

12345678 A B C D 87654321 D C B A SHEET OF REV Model NO. DWG TITLE Approve By / Date Engineer / Date Wistron NeWeb Corp. PCI_MODE C5 PCI_RST_L# P3 PCI_CLK P7 PCI_CLKRUN_L# J1 PCI_AD0 K14 PCI_AD1 K13 PCI_AD2 K12 PCI_AD3 L14 PCI_AD4 L13 PCI_AD5 L12 PCI_AD6 M14 PCI_AD7 M13 PCI_AD8 N14 PCI_AD9 N13 PCI_AD10 P13 PCI_AD11 N12 PCI_AD12 P12 PCI_AD13 M11 PCI_AD14 N11 PCI_AD15 P11 PCI_AD16 P10 PCI_AD17 P5 PCI_AD18 N5 PCI_AD19 P4 PCI_AD20 N4 PCI_AD21 M4 PCI_AD22 N3 PCI_AD23 P1 PCI_AD24 M2 PCI_AD25 L3 PCI_AD26 L2 PCI_AD27 K3 PCI_AD28 K2 PCI_AD29 K1 PCI_AD30 J3 PCI_AD31 J2 PCI_CBE0_L# P14 PCI_CBE1_L# N10 PCI_CBE2_L# M6 PCI_CBE3_L# M1 PCI_INT_L# P8 PCI_REQ_L# N1 PCI_GNT_L# M8 PCI_PERR_L# P9 PCI_PAR N9 PCI_IRDY_L# P6 PCI_TRDY_L# N7 PCI_FRAME_L# N6 PCI_STOP_L# N8 PCI_SERR_L# P2 PCI_DEVSEL_L# M7 PCI_IDSEL M9 PCI_PME_L# L1 XIN B11 XOUT C11 RX5 E1 RX2 D1 CLKOBS F13 REFCLK D14 PLLBYPASS E14 RFSHIFT A13 RFDATAOUT_0 A14 RFDATAOUT_1 B14 RFDATAOUT_2 C13 RFDATAOUT_3 C14 RFDATAIN5 D13 RFRESET_L# A12 RFLOAD B12 ANTA J14 ANTB J13 TX5 E12 TX2 E13 ANTC D12 ANTD F12 F2D2EN F14 TMS A3 TDI A2 TDO C2 TCLK C1 TRST_L# B1 GPIO_0 D2 GPIO_1 D3 GPIO_2 E2 GPIO_3 E3 GPIO_4 G13 GPIO_5 G14 LED_0 H13 LED_1 H14 RX_CLEAR F3 RFDATAIN2 G2 ATTEN5 H2 ATTEN2 J12 SLEEP H12 HITUNE5 G12 EPRM_EN_L# A1 EPRM_CS G1 EPRM_CLK H1 EPRM_DI F1 EPRM_DO F2 GND N2 GND M12 GND M3 GND L11 GND L9 GND L6 GND L4 GND K10 GND K9 GND K8 GND K7 GND K6 GND K5 GND J11 GND J10 GND J9 GND J8 GND J7 GND J6 GND J5 GND J4 GND H10 GND H9 GND H8 GND H7 GND H6 GND H5 GND G10 GND G9 GND G8 GND G7 GND G6 GND G5 GND F11 GND F10 GND F9 GND F8 GND F7 GND F6 GND F5 GND F4 GND E10 GND E9 GND E8 GND E7 GND E6 GND E5 GND D11 GND D9 GND D6 GND D4 GND C12 GND C3 GND B13 GND B2 VDD2_5 G3 VDD2_5 G4 VDD2_5 H3 VDD2_5 H4 VDD2_5 D7 VDD2_5 L7 VDD2_5 D8 VDD2_5 L8 VDD2_5 G11 VDD2_5 H11 VDD3_3 E4 VDD3_3 K4 VDD3_3 D5 VDD3_3 L5 VDD3_3 M5 VDD3_3 D10 VDD3_3 L10 VDD3_3 M10 VDD3_3 E11 VDD3_3 K11 AVDD_ADC C4 AVDD_ADC B7 AVDD_DAC C8 AVDD_DAC C9 AVDD_PLL C10 ADCISEL C7 ADCRES C6 ADC_QN A4 ADC_QP B4 ADC_IP A6 ADC_IN B6 DAC_QN A8 DAC_QP B8 DAC_IP A10 DAC_IN B10 AGND B3 AGND A5 AGND B5 AGND A7 AGND A9 AGND B9 AGND A11 U1 AR5213 R8 R 3.3V RX5 AR5112_CLK40_OUT RFSHIFT RFDATAOUT0 RFDATAOUT1 RFDATAOUT2 RFDATAOUT3 RFDATAIN RFRESET_L RFLOAD TX5 TX2 F2D2EN GPIO_0 GPIO_3 LED0 LED1 RX_CLEAR ATTEN5 ATTEN2 SLEEP HITUNE5 EPRM_EN_L ANTA ANTB VCC 8 NC 7 NC 6 GND 5 CS 1 SK 2 D1 3 DO 4 U2 AT93C86-10SI-2.7 3.3V EPRM_CS EPRM_CLK EPRM_DI EPRM_DO C4 0.01uF C5 0.01uF C6 0.01uF C7 0.1uF C8 0.1uF C9 0.1uF C10 10pF C11 10pF VCC_CORE C12 0.01uF C13 0.01uF C14 0.01uF C15 0.1uF C16 0.1uF C17 0.1uF C18 10pF C19 10pF 3.3V VCC_CORE3.3VVCC_ADC VCC_DAC ADCISELADCRES C1 22pF R2 6.19K 1% ADCN_Q ADCP_Q ADCP_I ADCN_I R110 R R111 R DACN_Q DACP_Q DACP_I DACN_I Ray Lee 11/12.2003 Abber Lee 11/12.2003 14 AR5213 and MiniPCI CM9 00C 41 32.768Khz Y1 C3 22pF R114 6.8M C2 22pF R54 10K 1% 3.3V 25V25V25V10V10V 25V25V25V10V10V10V RING 2 8PMJ-1 4 8PMJ-2 6 8PMJ-4 8 8PMJ-5 10 LED2-YELP 12 LED2-YELN 14 RESERVED1 16 5V 18 INTA# 20 RESERVED3 22 3.3VAUX 24 RST# 26 3.3V 28 GNT# 30 GND 32 PME# 34 RESERVED4 36 AD30 38 3.3V 40 AD28 42 AD26 44 AD24 46 IDSEL 48 GND 50 AD22 52 AD20 54 PAR 56 AD18 58 AD16 60 GND 62 FRAME# 64 TRDY# 66 STOP# 68 3.3V 70 DEVSEL# 72 GND 74 AD15 76 AD13 78 AD11 80 GND 82 AD9 84 CBE0# 86 3.3V 88 AD6 90 AD4 92 AD2 94 AD0 96 RESERVED-WIP1 98 RESERVED-WIP2 100 GND 102 M66EN 104 AC_SDATA_OUT 106 AC_CODEC_ID0# 108 AC_RESET# 110 RESERVED7 112 GND 114 SYS_AUDIO_IN 116 GNDSYS_AUDIO_IN_GND 118 AUDIO_GND 120 MPCIACT# 122 3.3VAUX 124 TIP 1 8PMJ-3 3 8PMJ-6 5 8PMJ-7 7 8PMJ-8 9 LED1-GRNP 11 LED1-GRNN 13 CHSGND 15 INTB# 17 3.3V 19 RESERVED2 21 GND 23 CLK 25 GND 27 REQ# 29 3.3V 31 AD31 33 AD29 35 GND 37 AD27 39 AD25 41 RESERVED5 43 CBE3# 45 AD23 47 GND 49 AD21 51 AD19 53 GND 55 AD17 57 CBE2# 59 IRDY# 61 3.3V 63 CLKRUN# 65 SERR# 67 GND 69 PERR# 71 CBE1# 73 AD14 75 GND 77 AD12 79 AD10 81 GND 83 AD8 85 AD7 87 3.3V 89 AD5 91 RESERVED6 93 AD3 95 5V 97 AD1 99 GND 101 AC_SYNC 103 AC_SDATA_IN 105 AC_BIT_CLK 107 AC_CODEC_ID1# 109 MOD_AUDIO_MON 111 AUDIO_GND 113 SYS_AUDIO_OUT 115 SYS_AUDIO_OUT_ 117 AUDIO_GND 119 RESERVED8 121 VCC5VA 123 J1 MINI PCI -TYPE III R61 R R59 187 1% 3.3V PCI_INT_L PCI_RST_L PCI_GNT_L AD30 3.3V_CON AD28 AD26 AD24 PCI_IDSEL_L AD22 AD20 PCI_PAR AD18 AD16 PCI_FRAME_L PCI_TRDY_L PCI_STOP_L PCI_DEVSEL_L AD15 AD13 AD11 AD9 PCI_CBE0_L AD6 AD4 AD2 AD0 R57 R MPCI_11 MPCI_13 R58 187 1% 3.3V PCI_CLK PCI_REQ_L AD31 AD29 AD27 AD25 PCI_CBE3_L AD23 AD21 AD19 AD17 PCI_CBE2_L PCI_IRDY_L PCI_CLKRUN_L PCI_SERR_L PCI_PERR_L PCI_CBE1_L AD14 AD12 AD10 AD8 AD7 AD5 AD3 AD1 3.3V_CON 2 3 1 Q12 2 3 1 Q11 3.3V_CON R9 R R5 4.7K 3.3V_AUX 3.3V STUFF ALL EXCEPT R9 FOR WAKE ON LAN. STUFF ONLY R9 TO DISABLE WAKE ON LAN. R83 R R60 0 R55 10K 3.3V MPCI_13LED1 GPIO_0 R86 R R88 0 MPCI_14LED0 GPIO_3 R82 R R84 0 MPCI_11LED0 GPIO_1 R85 R R87 0 MPCI_12LED1 GPIO_2 MPCI_14 MPCI_12 PCI_RST_L PCI_CLK PCI_CLKRUN_L AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 AD16 AD17 AD18 AD19 AD20 AD21 AD22 AD23 AD24 AD25 AD26 AD27 AD28 AD29 AD30 AD31 PCI_CBE0_L PCI_CBE1_L PCI_CBE2_L PCI_CBE3_L PCI_INT_L PCI_REQ_L PCI_GNT_L PCI_PERR_L PCI_PAR PCI_IRDY_L PCI_TRDY_L PCI_FRAME_L PCI_STOP_L PCI_SERR_L PCI_DEVSEL_L PCI_IDSEL_L TP30 TP5 TEST POINT TP8 TEST POINT TP1 TP3 TEST POINT TP29 TEST POINT 5v VCC5vA GPIO_2 GPIO_1 R103 R R104 10K 3.3V R102 R C353 0.1uF R101 10K 3.3V POR_L POR_EN Q9 2N3904 R6 3.09K R10 10K IRLM6401 IRLM6401 3.3V A1 1 A2 3 Y1 6 Y2 4 2 5 U7 NC7WZ07 HITUNE5 RX_CLEAR PCI_PME_L TP6 TEST POINT RX2 TP7 TEST POINT TP9 TEST POINT 123456 A B C D 654321 D C B A SHEET OF REV Model NO. DWG TITLE Approve By / Date Engineer / Date Wistron NeWeb Corp. Vdd2a 64 Vdd3a 63 Gnd2a 62 TXin_Ip 61 TXin_In 60 TXin_Qn 59 TXin_Qp 58 Gnd2a 57 RXout_In 56 RXout_Ip 55 RXout_QP 54 RXout_Qn 53 Gnd2a 52 Ftest_n 51 Ftest_p 50 Vdd2a 49 Gnd2a 48 RF2in_n 47 RF2in_p 46 RF5in_p 45 RF5in_n 44 Vdd2pa 43 Boutn_dc 42 RF2out_n 41 RF2out_n 40 RF2out_p 39 RF2out_p 38 Boutp_dc 37 Bres 36 Vdd2pa 35 Pdetect2 34 P…

Text truncated - open the document above for the full version.

55 44 33 22 11 D D C C B B A A short circuit short circuit POWER X10 Cherrystone Custom 217 , 05, 2004 星期五 十一月 TitleSize Document Number Rev Date: Sheet of +3V3 +1V3 +3V3 +VCC +5V +VCC_down +VCC +VCC_down U2CS51031 1234 5678 VGPGNDCoscGND VFB VCC CSVC L10CHOKE C19100pF,0805 L1 CHOKE F1 1.6A C10470pF + C12100uF/25V + C4 1000uF/25V C269 10uF/16V C270 0.1uF + C271470uF/16V D1 1N5817 12 C200.1uF C20.1uF C90.1uF + C6470uF/16V R51.5K,1% C31000pF R42.49K,1% R310,0805 C70.1uF VA1ESD R110,0805 J1 HEADER 12 R24.7,0805 C81000pF,0805 J3 HEADER 12J2 HEADER 12 L4BEAD,1206 + C21100uF/25V JP1 POWER JACK 3 1 2 + C274470uF/16V R610K U30 APL5901 1 2 3 Vin ADJ Vout SW1SWITCH 4X2 25 1436 AB A1B2A2B1 C181uF L3 CHOKE C220.1uF L2100uH,4A R8722 U1IRF7416 1234 5678 SSSGD DDD C27210uF/16V C27310uF/16V + C17 100uF/25V + C266470uF/16V C26710uF/16V C2680.1uF U4 NS LP3965ES-ADJ 2 4 1 3 5 VIN VOUT SD GND ADJ C110.33uF R71k,1%R810K,1% + C5100uF/25V U31 MC7805 1 2 3 Vin ADJ Vout 55 44 33 22 11 D D C C B B A A +1V3 KEEP VOLTAGE AT +1V3 Reset X10 Cherrystone B 317 , 05, 2004 星期五 十一月 TitleSize Document Number Rev Date: Sheet of JTAG_RESET RST1 RST2 /RESET RESET_N1 FT_RST JTG_SRST_N 17 FACTORY_RESET 6 PCI_CLK_USB RST_MINI_PCI 16RST_SW_PHY 12SOFT_RST_SW_PHY 17RST_PCI_USB2.0SOFT_RST_MINI 17SOFT_RST_USB2.0 17 RST_IRDA RST_CPU_FLASH 4,8 PWRON_RST_N 4 PCI_CLK_CPU 6PCI_CLK_Mini 16EXPB_CLK 5 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 +3V3 SW2 PUSH_BOTTOM R204.7K U33A74LVC14 1 2 U33B74LVC14 3 4 U7A SN74LVC08APWR TSSOP14 12 3 U7B SN74LVC08APWR TSSOP14 45 6 U7CSN74LVC08APWR TSSOP14 9 10 8 R224.7K U7DSN74LVC08APWR TSSOP14 1213 11 R244.7K OSC133MHz 32 41 OSC GND VCCNC/OE U8 CY2305 1234 5678 REFCLK1CLK2GND CLK3 VDD CLK4 CLKOUT R25NC R23100 C290.1uF R2651 R13NC R2110K C28NC C240.1uF C270.1uF SW4 PUSH_BOTTOM C30NC U5A 74AHC132PWR 12 3 147 U5B 74AHC132PWR 45 6 147 C31NC + C257 100uF/25V + C256 100uF/25V C32NC R184.7K R19 0 C33NC C260.1uF R27 300 R28 51 R29 51 R30 51 R31 51 R154.7K R91.5KR141K R164.7K U6LM809 1 2 3 GND RESET VCC R804.7K R124.7K R104.7K R114.7K R17300 C25100pF C230.1uF 55 44 33 22 11 D D C C B B A A for IXP 425 IXP-425(1) X10 Cherrystone B 417 , 05, 2004 星期五 十一月 TitleSize Document Number Rev Date: Sheet of SW_TXD2SW_TXD1SW_TXD0SW_TXD3 SCANTESTMODE_N PHY_RXD3SW_RXD3PHY_RXD1SW_RXD2SW_CRSPHY_RXD2 HIGHZ_N E_TXENE_TXD2E_TXD0 SW_RXD0 BYPASS_CLK E_TXD3E_TXD1P_TXEN 33.333M PHY_RXD0 33.333M SW_RXD1 UTP_OP_CLKUTP_IP_FCIUTP_IP_CLKUTP_IP_DATA0UTP_IP_DATA1UTP_IP_DATA3UTP_IP_DATA6UTP_IP_DATA7UTP_IP_DATA5UTP_IP_DATA2UTP_IP_SOCUTP_IP_DATA4UTP_OP_FCI SW_TXENSW_RXDV PHY_TXD0 P_TXD0 PHY_TXD2PHY_TXD3PHY_TXD1 P_TXD1 P_TXD3P_TXD2 JTG_TRST_N 17 PHY_RXD[3:0] PHY_TX_EN PHY_COL SW_TXEN 12 PHY_RX_CLK PHY_RX_DV RST_CPU_FLASH 3,8 PHY_CRS SW_RXDV 12 PHY_TX_CLKSW_RXD[3:0] 12 PWRON_RST_N 3 ICE_TCK 17 ICE_TDO 17 ICE_TMS 17 MDC MDIO ICE_TDI 17 SW_TXD[3:0] 12 PHY_TXD[3:0] CPU_TX_RX_CLK 17 SW_CRS 12 +1V3+1V3 +1V3 +3V3+3V3 +3V3 +3V3 +3V3 +3V3 R169 10K C1630.1uF R44 51 R45 51 R47 10K C390.1uF C380.1uF C400.01uF R50 10K R49 10K TP23 OSC2 33.333MHz 32 41 OSC GND VCCNC/OE C440.1uF C430.1uF C450.01uF RA251,8P4R 1234 5678 C420.1uF R1514.7K R1564.7K C370.01uF C360.1uF C350.1uF R4833 C41NC C34150pF,0402 U9A IXP425 AE3AE8 AD4 AF7 AD5 AF2 AB6 AD8AC5 AA7 AF1 AE1 AF6 AB9 AC8AD7AD2 AE6 AD1 AF5 AC2 AB4AA5AB3 AD6 AA9AB8 AF4 Y6 AE4 AA19AB20AF24AB19AF22AD20AC19AF21AE20AF20AB17AD18AA18AE22AC20AF19AC17AE18AF17AF16AC15AD15AF15AD14AE14AF14AB13AC16AE16AB15 AF26 AE24 AD23 AF25 AC22 AF9AF11 AF13 AD12AC13 AE10AE12AF23AD21AD17AF18 AB21 AD13 AE26 AF8AD10AF10AF12AC11 ETH_COL0ETH_COL1ETH_CRS0ETH_CRS1ETH_MDCETH_MDIOETH_RXCLK0ETH_RXCLK1ETH_RXDATA00ETH_RXDATA01ETH_RXDATA02ETH_RXDATA03ETH_RXDATA10ETH_RXDATA11ETH_RXDATA12ETH_RXDATA13ETH_RXDV0ETH_RXDV1ETH_TXCLK0ETH_TXCLK1ETH_TXDATA00ETH_TXDATA01ETH_TXDATA02ETH_TXDATA03ETH_TXDATA10ETH_TXDATA11ETH_TXDATA12ETH_TXDATA13ETH_TXEN0ETH_TXEN1 UTP_IP_ADDR0UTP_IP_ADDR1UTP_IP_ADDR2 UTP_IP_CLK UTP_IP_DATA0UTP_IP_DATA1UTP_IP_DATA2UTP_IP_DATA3UTP_IP_DATA4UTP_IP_DATA5UTP_IP_DATA6UTP_IP_DATA7 UTP_IP_FCI UTP_IP_FCO UTP_IP_SOC UTP_OP_ADDR0UTP_OP_ADDR1UTP_OP_ADDR2 UTP_OP_CLK UTP_OP_DATA0UTP_OP_DATA1UTP_OP_DATA2UTP_OP_DATA3UTP_OP_DATA4UTP_OP_DATA5UTP_OP_DATA6UTP_OP_DATA7 UTP_OP_FCI UTP_OP_FCO UTP_OP_SOC JTG_TCKJTG_TDIJTG_TDOJTG_TMSJTG_TRST_N OSC_IN OSC_OUT BYPASS_CLKPLL_LOCKRESET_IN_N VCCPLL1VCCPLL2 UTP_IP_ADDR3UTP_IP_ADDR4 UTP_OP_ADDR3UTP_OP_ADDR4 SCANTESTMODE_NPWRON_RESET_NHIGHZ_N VSSOSC VSSOSCPVSSOSCP VCCOSC VCCOSCP R149 51 TP1TP2TP3TP4TP5TP6TP7TP8TP9TP10 R171 0 RA151,8P4R 1234 5678 R172 0 TP11TP12TP13TP14TP15TP16TP18TP17TP19TP20TP21 U2674AHC1G32 123 54 ABGND VCC Y R32 10K R33 10K R34 10K R35 10K R36 10K R37 10K R38 10K R39 10K R40 10K R41 10K R42 10K R43 10K TP22 R46 10K 55 44 33 22 11 D D C C B B A A up=>533MHz run 533MHz 266MHz run 266MHzdown=>533MHz and 266MHzrun 266MHz Flash=>16 bit PCI Bus=>33MHz Clock Select for IXP 425 for IXP 425 Pull down resistors are recommended by IXP425datasheet when the signals are not being used. These resistors are placed for the case that amodule is not plugged in. 10K chosen to allowmodule to easily drive over the pull-down. IXP-425(2) X10 Cherrystone B 517 , 05, 2004 星期五 十一月 TitleSize Document Number Rev Date: Sheet of EE_CLKCPU_EE_CSN EE_DOUT EE_DIN EXPB_ADDR10EXPB_ADDR9EXPB_ADDR19EXPB_ADDR11EXPB_ADDR16EXPB_ADDR20EXPB_ADDR18EXPB_ADDR12EXPB_ADDR4EXPB_ADDR6EXPB_ADDR17EXPB_ADDR0EXPB_ADDR13EXPB_ADDR7EXPB_ADDR2EXPB_ADDR15EXPB_ADDR22EXPB_ADDR5EXPB_ADDR3EXPB_ADDR14EXPB_ADDR1EXPB_ADDR21EXPB_ADDR8EXPB_ADDR23 EXPB_AR23 EXPB_AR4EXPB_AR0 EXPB_AR23 EXP_D1EXP_D8EXP_D3 EXPB_AR3EXPB_AR10 EXP_D5EXP_D9EXPB_HRDY_N2EXP_D2EXP_D15 EXPB_AR1EXPB_AR6EXPB_AR19 EXP_D12EXPB_HRDY_N1 EXPB_AR9EXPB_AR15EXPB_AR16 EXP_D11EXPB_HRDY_N0 EXPB_AR17 EXPB_HRDY_N3 EXPB_AR5EXPB_AR13EXPB_AR18 EXP_D10 EXPB_AR12 FLASH_CS_N1 EXPB_AR2EXPB_AR4EXPB_AR22 EXP_D7EXP_D13EXP_D14 EXPB_AR11EXPB_AR14 EXP_D6 EXPB_AR8EXPB_AR20 EXP_D4 EXPB_AR0EXPB_AR7EXPB_AR21 EXP_D0 HSS_RXCLK0HSS_RXDATA0HSS_RXDATA1HSS_RXFRAME1HSS_RXCLK1HSS_RXFRAME0 HSS_TXC…

Text truncated - open the document above for the full version.

Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 1 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A FCC TEST REPORT according to FCC Rules and Regulations Part 15 Subpart C & E Laboratory accreditation 1332 ILAC MRA † The test result refers exclusively to the test presented test model / sample., † Without written approval of Exclusive Certification Corp. the test report shall not be reproduced except in full. † The EUT is also considered as a kind of computer peripheral, because the connection to computer is necessary for typical use. It has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Applicant Firetide Inc. Address 16795 Lark Ave., Ste. 200, Los Gatos, CA 95032 Equipment HotPort Wireless Mesh Node Model No. 3100 FCC ID REP-3100-1 Trade Name Firetide Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 2 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A CONTENTS 1. Report of Measurements and Examinations..................................................................................5 1.1. List of Measurements and Examinations............................................................................5 2. Test Configuration of Equipment under Test..................................................................................6 2.1. Test Mode and Test Software.............................................................................................6 2.2. Description of Test System................................................................................................6 2.3. Connection Diagram of Test System..................................................................................6 2.4. Feature of Equipment under Test.......................................................................................7 2.5. RF Module Specifications..................................................................................................7 2.6. History of this test report...................................................................................................7 3. General Information of Test.........................................................................................................8 4. Antenna Requirements................................................................................................................9 4.1. Standard Applicable..........................................................................................................9 4.2. Antenna Construction and Directional Gain........................................................................9 5. Test of Conducted Emission......................................................................................................10 5.1. Test Procedures..............................................................................................................10 5.2. Typical Test Setup Layout of Conducted Emission.............................................................11 5.3. Conducted Emission Requirement....................................................................................11 5.4. Test Result and Data.......................................................................................................12 6. Test of Radiated Emission.........................................................................................................25 6.1. Test Procedures..............................................................................................................25 6.2. Typical Test Setup Layout of Radiated Emission...............................................................25 6.3. Test Result of Radiated Emission.....................................................................................26 7. Peak Transmit Power................................................................................................................34 7.1. Test Procedure...............................................................................................................34 7.2. Test Setup Layout...........................................................................................................34 7.3. Test Result and Data.......................................................................................................34 8. Peak Power Excursion..............................................................................................................41 8.1. Test Procedure...............................................................................................................41 8.2. Test Setup Layout...........................................................................................................41 8.3. Test Result and Data.......................................................................................................41 9. Peak Power Spectral Density.....................................................................................................45 9.1. Test Procedure...............................................................................................................45 9.2. Test Setup Layout...........................................................................................................45 9.3. Test Result and Data.......................................................................................................45 10. Frequency Stability...................................................................................................................49 10.1. Test Procedure...............................................................................................................49 10.2. Test Setup Layout...........................................................................................................49 10.3. Test Result and Data............................................................................................…

Text truncated - open the document above for the full version.

Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 18 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 19 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 20 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 21 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 22 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 23 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A Test By: Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 24 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A 5.4.1. Photographs of Conducted Emission Test Front View Rear View

Exclusive Certification Corp. Tel:886-2-2792-3366 Fax:886-2-2792-1100 Issued date: Feb. 24, 2005 25 of 69 FCC ID: REP-3100-1 FCC Test Report: FE05011801-A 6. Test of Radiated Emission Radiated emissions from 30 MHz to 40 GHz were measured according to the methods defines in ANSI C63.4-2003. The EUT was placed, 0.8 meter above the ground plane, as shown in section 1.4.2. The interface cables and equipment positions were varied within limits of reasonable applications to determine the positions producing maximum radiated emissions 6.1. Test Procedures 1. The EUT was placed on a rotatable table top 0.8 meter above ground. 2. The EUT was set 3 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. 3. The table was rotated 360 degrees to determine the position of the highest radiation. 4. The antenna is a broadband antenna and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. 5. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. 6. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function and specified bandwidth with Maxim…

Text truncated - open the document above for the full version.