RI7CE910B-DUALCDMA Module

CE910 Series Hardware User Guide 1vv0301010 Rev.11 – 2015-10-27 CE910 Family Hardware User Guide 1vv0301010 Rev.11 – 2015-10-27 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 2 of 75 APPLICABILITY TABLE PRODUCT CE910-DUAL CE910-SC CE910B-DUAL CE910 Family Hardware User Guide 1vv0301010 Rev.11 – 2015-10-27 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 3 of 75 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to assure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies or omissions. Telit reserves the right to make changes to any products described herein and reserves the right to revise this document and to make changes from time to time in content hereof with no obligation to notify any person of revisions or changes. Telit does not assume any liability arising out of the application or use of any product, software, or circuit described herein; neither does it convey license under its patent rights or the rights of others. It is possible that this publication may contain references to, or information about Telit products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that Telit intends to announce such Telit products, programming, or services in your country. Copyrights This instruction manual and the Telit products described in this instruction manual may be, include or describe copyrighted Telit material, such as computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material of Telit and its licensors contained herein or in the Telit products described in this instruction manual may not be copied, reproduced, distributed, merged or modified in any manner without the express written permission of Telit. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit, as arises by operation of law in the sale of a product. Computer Software Copyrights The Telit and 3rd Party supplied Software (SW) products described in this instruction manual may include copyrighted Telit and other 3rd Party supplied computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and other 3rd Party supplied SW certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Telit or other 3rd Party supplied SW computer programs contained in the Telit products described in this instruction manual may not be copied (reverse engineered) or reproduced in any manner without the express written permission of Telit or the 3rd Party SW supplier. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit or other 3rd Party supplied SW, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product. CE910 Family Hardware User Guide 1vv0301010 Rev.11 – 2015-10-27 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 4 of 75 Usage and Disclosure Restrictions License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement. Copyrighted Materials Software and documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the software or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of Telit High Risk Materials Components, units, or third-party products used in the product described herein are NOT fault-tolerant and are NOT designed, manufactured, or intended for use as on-line control equipment in the following hazardous environments requiring fail-safe controls: the operation of Nuclear Facilities, Aircraft Navigation or Aircraft Communication Systems, Air Traffic Control, Life Support, or Weapons Systems (High Risk Activities"). Telit and its supplier(s) specifically disclaim any expressed or implied warranty of fitness for such High Risk Activities. Trademarks TELIT and the Stylized T Logo are registered in Trademark Office. All other product or service names are the property of their respective owners. Copyright © Telit Communications S.p.A. CE910 Family Hardware User Guide 1vv0301010 Rev.11 – 2015-10-27 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 5 of 75 Contents 1. Introduction ...................................................... 8 1.1. Scope .......................................................... 8 1.2. Audience ....................................................... 8 1.3. Contact Information, Support ................................... 8 1.4. Document Organization ......…

Text truncated - open the document above for the full version.

RE FCC ID: R17CE910B-DUAL To the certification reviewer: We are hereby applying for full modular approval of the above-referenced FCC ID, based on compliance with all of the criteria as detailed below. Sincerely, [signature] [name] Sooyong.lee [title] Engineering Manager Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212 Requirement per 15.212 reference (i) The radio elements of the modular transmitter must have their own RF shielding. Sooyong.lee Yes, the EUT provides the RF shielding. (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided. Sooyong.lee All inputs to the module is buffered through logic and microprocessor inputs. (iii) The modular transmitter must have its own power supply regulation. Sooyong.lee The EUT is compliant with all Applicable FCC rules. Details instruction for maintaining compliance are given in the user manual. (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). Sooyong.lee The EUT meets the FCC antenna requirements; and photo of antenna are shown in the exhibit. (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 parameters. Sooyong.lee The EUT was tested in a stand-alone configuration. Photos are shown in the exhibit. (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. Sooyong.lee Please see exhibition label sample for the FCC ID of this module. And also in the exhibition user manual, there are instructions given to the OEM on how to label the end product. (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Sooyong.lee The EUT is compliant with FCC Part 22H, Part 24E, Part 90S and Part 15B. Detailed instructions for maintaining compliance are given in the User Manual. (viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Sooyong.lee This transmitter is categorically excluded from routine environmental evaluation for RF exposure.

To whom it may concern, Letter of Agency I, an officer of Telit Communications, S.p.A., do hereby authorize Intertek Testing Services (Mr. Terry Chan / Koo Wai Ip / Kenneth Wong) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment of the FCC Rules until further notice. I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Yours sincerely ____________________________________ Brian Tucker Senior Vice President of Quality Telit Wireless Solutions, Inc. October 7, 2015

To whom it may concern, Request for Permanent Confidentiality Under FCC Part 22H, Part 24E, Part 90S, Part 15 FCC ID: [RI7CE910B-DUAL] Request is hereby submitted by Telit Communications, S.p.A. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR § 0.457(d) and § 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and Telit Communications, S.p.A. reserves the right to discern which parties can obtain access to these information:  Schematics  Detailed Block diagrams  Detailed Operational/Functional Description  Parts List  Tune up Procedures  Operational Description The rationale for request for confidentiality is as followings: This information represents intellectual property of Telit Communications, S.p.A. and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Yours sincerely ____________________________________ Brian Tucker Senior Vice President of Quality Telit Wireless Solutions, Inc. October 7, 2015

INTERTEK TESTING SERVICE Report No.: 15090562HKG-001 Equipment Photographs (External)

The label will be positioned on the top of the module. 25mm 25mm

INTERTEK TESTING SERVICE Report No.: 15090562HKG-001 Equipment Photographs (Internal) INTERTEK TESTING SERVICE Report No.: 15090562HKG-001 Equipment Photographs (Internal) INTERTEK TESTING SERVICE Report No.: 15090562HKG-001 Equipment Photographs (Internal)

INTERTEK TESTING SERVICES FCC ID: RI7CE910B-DUAL RF exposure - 1 of 1 For Maximum Permissible Exposure (MPE) evaluation of the base unit, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65 and meet the requirement listed in KDB447498. For the 850 and 1900 MHz CDMA Module of tested model: CE910B-DUAL, the averaged powers among all the channels were within its production tolerance: +23 dBm (Minimum) and +25 dBm (Maximum).The antenna gain of CE910B-DUAL is 5.12 dBi = 3.25 (num gain). From these data and its operating configuration – Mobile device, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The Conducted Power = 25 dBm = 316.2 mW The power density at 20cm = 316.23 *3.25/ 4πR 2 = 0.2046 mW cm -2 In the frequency range of 300-1500MHz, the MPE limit is f/1500 - 0.55mWcm -2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the base unit at least 20cm from nearby persons.”

INTERTEK TESTING SERVICES FCC ID: RI7CE910B-DUAL RF exposure - 1 of 1 For Maximum Permissible Exposure (MPE) evaluation of the base unit, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65 and meet the requirement listed in KDB447498. For the 850 MHz and 1900 MHz CDMA Module of tested model: CE910B-DUAL, the averaged powers among all the channels were within its production tolerance: +23 dBm (Minimum) and +25 dBm (Maximum).The antenna gain of CE910B-DUAL is 6.12 dBi = 4.09 (num gain). From these data and its operating configuration – Mobile device, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The Average Power = 25 dBm = 316.2 mW The power density at 20cm = 316.2 *4.09/ 4πR 2 = 0.2576 mW cm -2 In the frequency range of 1,500 - 100,000MHz, the MPE limit is 1.0 mWcm -2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the base unit at least 20cm from nearby persons.”

INTERTEK TESTING SERVICES FCC ID: RI7CE910B-DUAL RF exposure - 1 of 1 For Maximum Permissible Exposure (MPE) evaluation of the base unit, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65 and meet the requirement listed in KDB447498. For the 850 and 1900 MHz CDMA Module of tested model: CE910B-DUAL, the averaged powers among all the channels were within its production tolerance: +23 dBm (Minimum) and +25 dBm (Maximum).The antenna gain of CE910B-DUAL is 5.12 dBi = 3.25 (num gain). From these data and its operating configuration – Mobile device, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The Conducted Power = 25 dBm = 316.2 mW The power density at 20cm = 316.23 *3.25/ 4πR 2 = 0.2046 mW cm -2 In the frequency range of 300-1500MHz, the MPE limit is f/1500 - 0.55mWcm -2 for general population and uncontrolled exposure. As the measured power density at 20cm from the transmitter is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the base unit at least 20cm from nearby persons.”

INTERTEK TESTING SERVICES Bandedge Plots Bandedge - 1 of 1 Lowest Channel (BC 0) Highest Channel (BC 0) INTERTEK TESTING SERVICES Bandedge Plots Bandedge - 1 of 1 Lowest Channel (BC 1) Highest Channel (BC 1)

INTERTEK TESTING SERVICES Bandedge Plots Bandedge - 1 of 2 Lowest Channel (BC 10) , RBW = 1 % of EBW Lowest Channel (BC 10), RBW of 1% of 37.5kHz of outer channel frequency block INTERTEK TESTING SERVICES Bandedge Plots Bandedge - 2 of 2 Highest Channel (BC 10) , RBW = 1 % of EBW Highest Channel (BC 10), RBW of 1% of 37.5kHz of outer channel frequency block

INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 1 of 2 Lowest channel (BC0) Middle channel (BC0) INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 2 of 2 Highest Channel (BC0) INTERTEK TESTING SERVICES Occupied Bandwidth Plots OBW - 1 of 2 Lowest channel (BC0) Middle channel (BC0) INTERTEK TESTING SERVICES Occupied Bandwidth Plots OBW - 2 of 2 Highest Channel (BC0) INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 1 of 2 Lowest channel (BC1) Middle channel (BC1) INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 2 of 2 Highest Channel (BC1) INTERTEK TESTING SERVICES Bandedge Plots Bandedge - 1 of 1 Lowest Channel (BC 1) Highest Channel (BC 1)

INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 1 of 2 Lowest channel (BC10) Middle channel (BC10) INTERTEK TESTING SERVICES -26dB Bandwidth Plots -26dB - 2 of 2 Highest Channel (BC10) INTERTEK TESTING SERVICES Occupied Bandwidth Plots OBW - 1 of 2 Lowest channel (BC10) Middle channel (BC10) INTERTEK TESTING SERVICES Occupied Bandwidth Plots OBW - 2 of 2 Highest Channel (BC10)

INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 1 of 3 Lowest channel (BC0) Lowest channel (BC0) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 2 of 3 Middle channel (BC1) Middle channel (BC1) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 3 of 3 Highest Channel (BC1) Highest Channel (BC1) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 1 of 3 Lowest channel (BC1) Lowest channel (BC1) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 2 of 3 Middle channel (BC1) Middle channel (BC1) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 3 of 3 Highest Channel (BC1) Highest Channel (BC1)

INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 1 of 3 Lowest channel (BC10) Lowest channel (BC10) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 2 of 3 Middle channel (BC10) Middle channel (BC10) INTERTEK TESTING SERVICES Spurious Emissions At Antenna Terminals Conducted Spurious Emission - 3 of 3 Highest Channel (BC10) Highest Channel (BC10)

- Intertek's standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report No.: 15090562HKG-001R1 Telit Communications S.p.A. Application For Original Grant of 47 CFR Part 22, Part 24, IC RSS-132 and IC RSS-133 Certification CDMA Module (FCC ID: RI7CE910B-DUAL) (IC: 5131A-CE910BDUAL) This report supersedes previous report with report number 15090562HKG-001 dated October 14, 2015. Prepared and Checked by: Approved by: Signed On File Lee Shui Tim Lead Engineer Koo Wai Ip Assistant Supervisor Date: November 26, 2015 INTERTEK TESTING SERVICES Report No.: 15090562HKG-001R1 1 FCC ID: RI7CE910B-DUAL IC: 5131A-CE910BDUAL GENERAL INFORMATION Applicant Name: Telit Communications S.p.A. Applicant Address: Via Stazione di Prosecco 5/B Trieste 34010 Italy FCC Specification Standard: FCC Part 22: 2014 FCC Part 24: 2014 IC Specification Standard: IC RSS-132: 2013 IC RSS-133: 2013 FCC ID: RI7CE910B-DUAL FCC Model(s): CE910B-DUAL IC: IC: 5131A-CE910BDUAL Type of EUT: CDMA 850/1900 Transceiver Description of EUT: CDMA Module Serial Number: N/A Sample Receipt Date: September 09, 2015 Date of Test: September 13-30, 2015 Report Date: November 26, 2015 Environmental Conditions: Temperature: 25 ± 10°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: 15090562HKG-001R1 2 FCC ID: RI7CE910B-DUAL IC: 5131A-CE910BDUAL Table of Contents 1.0 Summary of Test Results ..................................................................................... 3 1.1 Statement of Compliance ................................................................................... 3 2.0 General Description .............................................................................................. 4 2.1 Product Description ............................................................................................ 4 2.2 Test Methodology ............................................................................................... 4 2.3 Test Facility ......................................................................................................... 4 3.0 System Test Configuration ................................................................................... 5 3.1 Justification .......................................................................................................... 5 3.2 Details of EUT and Description of Accessories .................................................. 6 3.3 Measurement Uncertainty................................................................................... 6 3.4 Equipment Modification ...................................................................................... 6 4.0 Test Results ........................................................................................................... 7 4.1 Channels for Cellular and Broadband PCS Services ......................................... 7 4.2 RF Power Output ................................................................................................ 8 4.3 Occupied Bandwidth ........................................................................................... 9 4.4 Spurious Emissions at Antenna Terminals ....................................................... 10 4.5 Power of Spurious Emissions ........................................................................... 11 4.6 Blockedge at Antenna Terminals ...................................................................... 12 4.7 Frequency Stability ........................................................................................... 13 4.8 Radio Frequency Exposure Compliance .......................................................... 17 4.9 Peak-to-average power ratio (PAPR).....................................................17 5.0 Equipment List .................................................................................................... 19 Appendix – Exhibits for Application of Certification INTERTEK TESTING SERVICES Report No.: 15090562HKG-001R1 3 FCC ID: RI7CE910B-DUAL IC: 5131A-CE910BDUAL 1.0 Summary of Test Results Test Items FCC Section IC Section Results Details see section Channels for Cellular and Broadband PCS Services 22.905 24.229 SRSP-503 SRSP-510 Pass 4.1 RF Output Power 2.1046 22.913 24.232 RSS-132(5.4) RSS-133(6.4)Pass 4.2 Occupied Bandwidth 2.1049 RSS-Gen (4.6.1) Pass 4.3 Spurious Emissions at Antenna Terminals 2.1051 2.1057 22.917 24.238 RSS-132(5.5) RSS-133(6.5) Pass 4.4 Power of Spurious Emissions 2.1053 2.1057 22.917 24.238 RSS-132(5.5) RSS-133(6.5) Pass 4.5 Blockedge at antenna terminal 22.917 24.238 RSS-132(5.5) RSS-132(6.5) Pass 4.6 Frequency Stability 2.1055 22.355 24.235 RSS-132(5.3) RSS-133(6.3)Pass 4.7 RF Exposure 1.1307 2.1093 RSS-102 Pass 4.8 Peak-to-average Power Ratio(P…

Text truncated - open the document above for the full version.

Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report Number: 15090562HKG-002R1 Application for Original Grant of 47 CFR Part 90 Certification CDMA Module (FCC ID: RI7CE910B-DUAL) This report supersedes previous report with report number 15090562HKG-002 dated October 14, 2015. Prepared and Checked by: Approved by: Signed On File Lee Shui Tim Lead Engineer Koo Wai Ip Assistant Supervisor Date: October 14, 2015 - Intertek's standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. - The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. INTERTEK TESTING SERVICES Report No.: 15090562HKG-002R1 FCC ID: RI7CE910B-DUAL Page 1 of 18 GENERAL INFORMATION Applicant Name: Telit Communications S.p.A. Applicant Address: Via Stazione di Prosecco 5/B Trieste 34010 Italy FCC Specification Standard: FCC Part 90:2014 FCC ID: RI7CE910B-DUAL FCC Model(s): CE910B-DUAL Type of EUT: CDMA 850/1900 Transceiver Description of EUT: CDMA Module Serial Number: N/A Sample Receipt Date: September 09, 2015 Date of Test: September 13-30, 2015 Report Date: October 14, 2015 Environmental Conditions: Temperature: 25 ± 10°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: 15090562HKG-002R1 FCC ID: RI7CE910B-DUAL Page 2 of 18 Table of Contents 1.0 Summary of Test Results.................................................................................................................................. 3 1.1 Statement of Compliance ................................................................................................................................3 2.0 General Description ............................................................................................................................................ 4 2.1 Product Description ........................................................................................................................................... 4 2.3 Test Methodology .............................................................................................................................................. 5 2.4 Test Facility ........................................................................................................................................................ 5 3.0 System Test Configuration................................................................................................................................6 3.1 Justification......................................................................................................................................................... 6 3.3 Details of EUT and Description of Accessories .............................................................................................. 8 3.4 Measurement Uncertainty................................................................................................................................. 8 3.5 Equipment Modification..................................................................................................................................... 8 4.0 Test Results.......................................................................................................................................................... 9 4.1 Frequency Available ........................................................................................................................................... 9 4.2 RF Power Output (FCC Part 2.1046, 90.635)............................................................................................. 10 4.3 Occupied Bandwidth (FCC Part 2.1049)....................................................................................................... 11 4.4 Spurious Emissions at Antenna Terminals (FCC Part 2.1051, 2.1057,90.691).......…

Text truncated - open the document above for the full version.