RIPHM360Handheld Marine Radio

RF Energy Exposure Compliance our radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic ener gy. This radio complies with the IEEE and ICNIRP exposure limits for general /uncontrolled RF exp osure environment at operating duty factors of up to 50% transmitting and is authorized by the F CC for general population use. In terms of measuring RF energy for compliance with the FCC expo sure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talk ing in PTT mode), not when it is receiving (listening) or in standby mode. The device complies wit h SAR and/or RF field strength limits of RSS‐102 requirement Your radio complies with the following of RF energy exposure standards and guidelines ● United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub‐part J ● American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers ( IEEE) C95. 1‐1992 ● Institute of Electrical and Electronic Engineers (IEEE) C95. 1‐1999 Edition ● International Commission on Non‐Ionizing Radiation Protection (ICNIRP) 1998 Operational Instructions and Training Guidelines To ensure optimal performance and compliance with the general /uncontrolled environment RF e nergy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedures; and should transmit no more tha n 50% of the time, although the hardware support transmission up to 100% of the time. Transmit and Receive To transmit (talk), push the Push‐To‐Talk (PTT) key; to receive, release the PTT key. EU Regulatory Conformance The equipment is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC. Note: The above information is applicable to EU countries only. FCC Licensing Information Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, p ursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection a gainst harmful interference in a residential installation. This equipment generates, uses and can r adiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that in terference will not occur in a particular installation. If this equipment does cause harmful interfer ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea sures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Licensing Requirements A license from Federal Communications Commission is required prior to use. Your dealer will prog ram each radio with your authorized frequencies, signaling codes, etc., and will be there to meet your communications needs as your system expands. Contact your dealer for more information. HM360 Instruction Manual 1,HM-360 KEY FUNCTION Keys Short press less than 3 seconds Long press more than 3 seconds HI/Lo /Lock TX Power Hi/Low Key Lock/key unlock 16/9 CH 16 CH09 DW/TriW Dual Watch mode Tri Watch mode WX/BAND Weather Channel UIC band SCAN All Scan/all memory Scan Priority all/memory Scan MEM MEMORY Mode Save/Delete Memory Channel Up/Down Channel/ Setting Up/Down Channel up /down(much faster) Menu/call DSC menu Main menu Scr/MOB Scrambler MOB activated Distress Distress menu Distress alert calling SQL Sql setting Switch on/off Time&Date display Volume Knob Power ON / OFF Adjust the volume level 2,HM-360 KEY DESCRPTION Note: In European version, WX function from the CH/WX/UIC key will be changed to PRIV function. 3, HM360-LCD DISPLAY 4, Menu Screen Operation: 4.1 DSC Menu: Short press the Call/Menu key will saw below DSC Menu as below. Then the CH/WX/UIC key will became the Exit key and the Call/Menu key will became the Enter key. The UP/DOWN key function has the same function to choose the item at the menu without the changes.  For My MMSI ID setup: Firstly, set up the MMSI ID, to click the My MMSI ID and Enter, then you are able to set up your related MMSI ID as below.Generally,you need to double confirm the MMSI ID then your MMSI ID will be locked by this radio.  For Individual Call, Position Request, Group Call and Test Call. Click the preferred item then you able to find the target MMSI ID to call by Input Address or From Phonebook. We take the individual call as an example. When you selected the input address item to click and input 9 digits such as the 100000000 for your address as below. Then select the type of individual call such as the safety then select the channels such as the 01 port operation then confirm to call. Then the individual call is sent. When you input 9 digits, UP/DOWN key to choose the number from1-9,you need to input all numbers from the left to right one by one.When you input all 9 digits then press the enter to confirm.  For All Ship Call: Select the All Ship Call item then select the type of All Ship Call such as the Urgency then select the channels such as the 07 Commercial then confirm to call. Then the All Ship Call is sent.  Receive Call Log When receive the DSC call and you able to check the message from the Distress Call then able to see the exact message.  Send Call Log To press the Send Call Log able to saw the previous Distress Call,MOB Call and Other Call you have sent  Phone Book: Able to check the contact ship by Buddy list and Group list  DSC Setup The DSC setup menu got the 4 it…

Text truncated - open the document above for the full version.

Shenzhen Jiuzhou Himunication Technology Co.,Ltd. FCC ID: RIPHM360 DATE: Feb 20, 2013 Dear sir / madam This is to declare that pursuant to the requirements contained in Part 80.225(a) of the Commission's Rules, this portable marine radio equipment with digital selective calling (DSC) functions - meets the specifications specified IEC62238. This portable marine radio equipment cannot support GMDSS. Sincerely yours, Shenzhen Jiuzhou Himunication Technology Co.,Ltd oliver.zou / RD manager Fax: + 86_755_26947285 Tel: + 86_755_26947359 E-mail: [email protected]

Shenzhen Jiuzhou Himunication Technology Co.,Ltd Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Shenzhen Jiuzhou Himunication Technology Co.,Ltd. would like the following documents regarding this submission for FCC ID: RIPHM360 to be kept confidential. 1. Block Diagram 2. Schematic 3. Theory of Operation 4. Tune-Up Procedure 5． Part List The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely yours, Shenzhen Jiuzhou Himunication Technology Co.,Ltd oliver.zou / RD manager Fax: + 86_755_26947285 Tel: + 86_755_26947359 E-mail: [email protected]

Shenzhen Jiuzhou Himunication Technology Co.,Ltd. FCC ID: RIPHM360 DATE: Jan 28, 2013 Dear sir / madam This equipment meets the requirements of the FCC Rules, Parts 80.203(b)3, as applicable. Programming of this product’s transmit frequencies can be performed only by the manufacturer of by service or by maintence personal. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely yours, Shenzhen Jiuzhou Himunication Technology Co.,Ltd oliver.zou / RD manager Fax: + 86_755_26947285 Tel: + 86_755_26947359 E-mail: [email protected]

FCC Label

Report No. RXA1212-1162SAR01R5 Page 1 of 73 TESTING No. L2264 OET 65 TEST REPORT Product Name handheld marine radio Model HM360 FCC ID RIPHM360 Client Shenzhen Jiuzhou Himunication Technology Co.,Ltd TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1212-1162SAR01R5 Page 2 of 73 GENERAL SUMMARY Product Name handheld marine radio Model HM360 FCC ID RIPHM360 Report No. RXA1212-1162SAR01R5 Client Shenzhen Jiuzhou Himunication Technology Co.,Ltd Manufacturer Shenzhen Jiuzhou Himunication Technology Co.,Ltd Reference Standard(s) IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 KHz to 300 GHz. SUPPLEMENT C Edition 01-01 to OET BULLETIN 65 Edition 97-01 June 2001 including DA 02-1438 June 19, 2002: Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Additional Information for Evaluation Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions. KDB 447498 D01 Mobile Portable RF Exposure v05: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies Tracking Number: 868998 Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: March 19 th , 2013 Comment The test result only responds to the measured sample. Approved by Director Revised by SAR Manager Performed by SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1212-1162SAR01R5 Page 3 of 73 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report.......................................................................................................5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT................................................................................................................ 7 1.6. The Maximum SAR 1g Values ................................................................................................ 8 1.7. Test Date .............................................................................................................................. 8 2. SAR Measurements System Configuration .................................................................................. 9 2.1. SAR Measurement Set-up .................................................................................................... 9 2.2. DASY5 E-field Probe System ............................................................................................. 10 2.2.1. ES3DV3 Probe Specification ....................................................................................... 10 2.2.2. E-field Probe Calibration .............................................................................................. 11 2.3. Other Test Equipment ......................................................................................................... 11 2.3.1. Device Holder for Transmitters .................................................................................... 11 2.3.2. Phantom...................................................................................................................... 12 2.4. Scanning Procedure........................................................................................................... 12 2.5. Data Storage and Evaluation .............................................................................................. 14 2.5.1. Data Storage................................................................................................................ 14 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 14 3. Laboratory Environment............................................................................................................. 16 4. Tissue-equivalent Liquid ............................................................................................................ 17 4.1. Tissue-equivalent Liquid Ingredients................................................................................... 17 4.2. Tissue-equivalent Liquid Properties .................................................................................... 18 5. System check and verification.................................................................................................... 19 5.1. Description of System Check .............................................................................................. 19 5.2. System verification.............................................................................................................. 20 5.3. SAR system validation and verification requirements below 300 MHz................................ 21 6. Operational Conditions during Test ............................................................................................ 23 6.1. General Description of Test Procedures............................................................................. 23 6.2. Test Configuration ............................................................................................................... 23 6.2.1. Face-Held Configuration .............................................................................................. 23 6.2.2. Body-Wor…

Text truncated - open the document above for the full version.

FCC PART 80 TEST REPORT FCC Part 80 Report Reference No......................: FCC ID..............................................: TRE12110048 R/C: 70799 RIPHM360 Compiled by ( position+printed name+signature)..: File administrators Tim Zhang Supervised by ( position+printed name+signature)..: Test Engineer Eric Zhang Approved by ( position+printed name+signature)..: Manager Wenliang Li Date of issue.....................................: Dec 14, 2012 Testing Laboratory Name..............: Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................: Keji Nan No.12 Road, Hi-tech Park, Shenzhen, China Applicant’s name............................: Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address ............................................: B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Test specification: Standard ...........................................: FCC Part 80: STATIONS IN THE MARITIME SERVICES TRF Originator..................................: Shenzhen Huatongwei International Inspection CO., Ltd Master TRF.......................................: Dated 2006-06 Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Handheld marine radio Trade Mark .......................................: / Manufacturer ....................................: Shenzhen Jiuzhou Himunication Technology Co.,Ltd Model/Type reference.......................: HM360 List Model .........................................: / Modulation......................................... FM Channe Separation............................ 25KHz Operation Frequency......................... From 156.05 MHz to 157.425 MHz Rated Power ....................................: 5 Watts(36.99dBm)/1 Watts(30.00dBm) Ratings .............................................: DC 7.4 V Result................................................: Positive Report No.: TRE12110048 Page 2 of 65 Issued:2012-12-14 FCC ID: RIPHM360 T E S T R E P O R T Test Report No. : TRE12110048 Dec 14, 2012 ______________________________________________________________________________________________ Date of issue Equipment under Test : Handheld marine radio Model /Type : HM360 Listed Models : / Applicant : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address : B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Manufacturer : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address : B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Test Result according to the standards on page 4: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: TRE12110048 Page 3 of 65 Issued:2012-12-14 FCC ID: RIPHM360 Contents 1. TEST STANDARDS 4 2. SUMMARY 5 2.1. General Remarks 5 2.2. Product Description 5 2.3. Equipment under Test 5 2.4. Short description of the Equipment under Test (EUT) 5 2.5. EUT Configuration 6 2.6. EUT operation mode 6 2.7. EUT configuration 6 2.8. Related Submittal(s) / Grant (s) 6 2.9. Modifications 6 2.10. Note 6 3. TEST ENVIRONMENT 7 3.1. Address of the test laboratory 7 3.2. Test Facility 7 3.3. Environmental conditions 8 3.4. Configuration of Tested System 8 3.5. Discription of Tested Modes 8 3.6. Statement of the measurement uncertainty 8 3.7. Test Description 9 3.8. Equipments Used during the Test 9 4. TEST CONDITIONS AND RESULTS 12 4.1. Conducted Emissions Test 12 4.2. Occupied Bandwidth and Emission Mask Test 15 4.3. Transmitter Radiated Spurious Emssion 23 4.4. Spurious Emssion on Antenna Port 27 4.5. Modulation Charcateristics 36 4.6. Frequency Stability Test 40 4.7. Maximum Transmitter Power 42 4.8. Receiver Radiated Spurious Emssion 47 4.9. Receiver Conducted Spurious Emssion 53 5. TEST SETUP PHOTOS OF THE EUT 58 6. EXTERNAL AND INTERNAL PHOTOS OF THE EUT 61 Report No.: TRE12110048 Page 4 of 65 Issued:2012-12-14 FCC ID: RIPHM360 1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 80: STATIONS IN THE MARITIME SERVICES. TIA/EIA 603 D: Land Mobile FM or PM Communications Equipment Measurement and Performance Standards. 47 CFR FCC Part 15 Subpart B - Unintentional Radiators FCC Part 2: FREQUENCY ALLOCA-TIONS AND RADIO TREATY MAT-TERS; GENERAL RULES AND REG-ULATIONS Report No.: TRE12110048 Page 5 of 65 Issued:2012-12-14 FCC ID: RIPHM360 2. SUMMARY 2.1. General Remarks Date of receipt of test sample : Nov 20, 2012 Testing commenced on : Nov 20, 2012 Testing concluded on : Dec 14, 2012 2.2. Product Description The Shenzhen Jiuzhou Himunication Technology Co.,Ltd’s Model: HM360 or the “EUT” as referred to in this report; more general information as follows, for more details, refer to the user’s manual of the EUT. Name of EUT Handheld marine radio Model Number HM360 Rated Output Power 5 Watts(36.99 dBm)/1 Watts(30.00 dBm) Modilation Type FM for Analog Voice Emission Designator Analog 16K0F3E for 25KHz Channel Separation Channel Separation Analog Voice 25KHz Antenna Type External Frequency Range From 156.05 MHz to 157.425 MHz 2.3. Equipment under Test Power supply system utilised Power supply voltage : ○ 120V / 60 Hz ○ 115V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 7.4 V Test frequency list Modulation Type Test Channe…

Text truncated - open the document above for the full version.

TEST REPORT IEC 62238 Report Reference No. ..................... : TRE1211004802 R/C: 70799 Compiled by ( position+printed name+signature) .. : File administrators Tim Zhang Supervised by ( position+printed name+signature) .. : Test Engineer Eric Zhang Approved by ( position+printed name+signature) .. : Manager Wenliang Li Date of issue ..................................... : March 04, 2013 Testing Laboratory Name .............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : Keji Nan No.12 Road, Hi-tech Park, Shenzhen, China Applicant’s name ............................ : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address ............................................. : B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Test specification: Standard ........................................... : IEC 62238:2002 TRF Originator .................................. : Shenzhen Huatongwei International Inspection CO., Ltd Master TRF ....................................... : Dated 2006-06 Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : Handheld marine radio Trade Mark ....................................... : / Manufacturer .................................... : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Model/Type reference ....................... : HM360 List Model ......................................... : / Modulation ......................................... G3E,G2B Channe Separation ............................ 25KHz Operation Frequency ......................... From 156.05 MHz to 157.425 MHz DSC class .......................................... D Rated Power .................................... : 5 Watts(36.99dBm)/1 Watts(30.00dBm) Ratings .............................................. : DC 7.4 V Result ................................................ : Positive Report No.: TRE1211004802 Page 2 of 100 Issued:2013-03-04 T E S T R E P O R T Test Report No. : TRE1211004802 March 04, 2013 ______________________________________________________________________________________________ Date of issue Equipment under Test : Handheld marine radio Model /Type : HM360 Listed Models : / Applicant : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address : B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Manufacturer : Shenzhen Jiuzhou Himunication Technology Co.,Ltd Address : B712, 7F, Jiuzhou Electric Building, Southern No.12 Road, Hi-tech Industrial Park, Nanshan District, Shenzhen, China Test Result according to the standards on page 4: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: TRE1211004802 Page 3 of 100 Issued:2013-03-04 Contents 1. TEST STANDARDS 5 2. SUMMARY 6 2.1. General Remarks 6 2.2. Product Description 6 2.3. Equipment Under Test 6 2.4. EUT operation mode 6 2.5. Configuration of Tested System 7 2.6. EUT configuration 7 2.7. Performance check 7 2.8. NOTE 8 3. TEST ENVIRONMENT 9 3.1. Address of the test laboratory 9 3.2. Test Facility 9 3.3. Environmental conditions 10 3.4. Test Description 10 3.5. Statement of the measurement uncertainty 11 3.6. Equipments Used during the Test 11 4. TEST CONDITIONS AND RESULTS 15 4.1. IEC 62338 REQUIREMENTS 15 4.1.1. Frequency Error 15 4.1.2. Carrier Power (Conducted) 16 4.1.3. Frequency Deviation 18 4.1.4. Sensitivity of the modulator, including microphone 21 4.1.5. Audio frequency response 22 4.1.6. Audio frequency harmonic distortion of the emission 24 4.1.7. Adjacent Channel Power 25 4.1.8. Conducted spurious emissions conveyed to the antenna 26 4.1.9. Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna 27 4.1.10. Transmitter Frequency Behavior 30 4.1.11. Residual modulation of the transmitter 32 4.1.12. Frequency error (DSC signal) 33 4.1.13. Modulation index for DSC 35 4.1.14. Modulation rate for DSC 36 4.1.15. Testing of generated call sequences 37 4.1.16. Harmonic distortion and rated audiofrequency output power for Radiotelephone receiver 38 4.1.17. Audiofrequency response for Radiotelephone receiver 39 4.1.18. Maximum Usable Sensitivity (Conducted) for Radiotelephone receiver 41 4.1.19. Co-channel Rejection for Radiotelephone receiver 42 4.1.20. Adjacent Channel Selectivity for Radiotelephone receiver 43 4.1.21. Spurious Response Rejection for Radiotelephone receiver 44 4.1.22. InterModulation Response Rejection for Radiotelephone receiver 45 4.1.23. Blocking or Desensitization for Radiotelephone receiver 46 4.1.24. Receiver conducted spurious emissions for Radiotelephone receiver 47 4.1.25. Receiver radiated spurious emissions for Radiotelephone receiver 49 4.1.26. Receiver residual noise level for Radiotelephone receiver 51 4.1.27. Squelch operation for Radiotelephone receiver 52 4.1.28. Squelch hysteresis for Radiotelephone receiver 53 4.1.29. Multiple watch characteristic for Radiotelephone receiver 54 Report No.: TRE1211004802 Page 4 of 100 Issued:2013-03-04 4.1.30. Maximum usable sensitivity for DSC decoder 55 4.1.31. Co-channel rejection for DSC decoder 56 4.1.32. Adjacent channel selectivity for DSC decoder 57 4.1.33. Spurious response and blocking immunity for DSC decoder 58 4.1.34. Intermodulation response for DSC decoder 59 4.1.35. Dynamic rang…

Text truncated - open the document above for the full version.