ROU0001010.1 Inch PAD

Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.

Shenzhen KTC Technology Co., Ltd. Northern Wuhe Road, Gangtou, Buji, Longgang, Shenzhen, China ----------------------------------------------------------------------------------------------------------------------------------- Declaration We Name:Shenzhen KTC Technology Co., Ltd. Address: Northern Wuhe Road, Gangtou, Buji, Longgang, Shenzhen, China Manufacturer: Shenzhen KTC Technology Co., Ltd. Address: Northern Wuhe Road, Gangtou, Buji, Longgang, Shenzhen, China Product description:10.1’’ PAD FCC ID:ROU00010 Model:800P31C, 800P**A, 800P**B, 800P**C, &&800****** Model Difference:101P**A, 101P**B, 101P**C 1st* could be 0-99 or A-Z, means different client code; 2nd* could be 0-99 or A-Z or blank, stands for the shape or color of enclosure, no impact on Products safety and EMC characteristics There are different marketing of the model(s). ------------------------------------- Signature: leon, Manager Date: 2014-09-29 101P51C, 101P**A, 101P**B, 101P**C All models are electrically identicalonly model no is different for marking use.

Leon Zheng

Leon Zheng

External Photo (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo

Internal Photo (1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo (5) EUT Photo (6) EUT Photo (7) EUT Photo (8) EUT Photo (9) EUT Photo (10) EUT Photo (11) EUT Photo (12) EUT Photo (13) EUT Photo

RF Exposure evaluation According to KDB 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Worse case is as below: [2412 MHz 9.51dBm（8.933mW） output power] (8.933mW /5mm) ·[√2.412 (GHz)]= 2.79 <3.0 for 1-g SAR Then SAR evaluation is not required

MRT Technology (Suzhou) Co., LtdReport No.: 1409RSU04601 Phone: +86-512-66308358Report Version: V01 Fax: +86-512-66308368Issue Date: 10-13-2014 Web: www.mrt-cert.com FCC ID: ROU00010 Page Number: 1 of 74 FCC ID:ROU00010 APPLICANT:SHENZHEN KTC TECHNOLOGY CO., LTD. Application Type:Certification Product:10.1”PAD Model No.:101P51C, 101P**A, 101P**B, 101P**C Brand Name:-- FCC Classification:Digital Transmission System (DTS) FCC Rule Part(s):Part 15.247 Test Procedure(s):ANSI C63.10-2009, KDB 558074 D01v03r02 Test Date:Oct. 08 ~ 12, 2014 MEASUREMENT REPORT FCC PART 15.247 WLAN 802.11b/g/n & BLE Reviewed By: ( Robin Wu ) Approved By: ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 558074 D01v03r02. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 2 of 74 Revision History Report No.VersionDescriptionIssue Date 1409RSU04601Rev. 01Initial report10-13-2014 Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 3 of 74 CONTENTS Description Page 1.INTRODUCTION ........................................................................................................................6 1.1.Scope ..............................................................................................................................6 1.2. MRT Test Location ..........................................................................................................6 2. PRODUCT INFORMATION ........................................................................................................7 2.1.Equipment Description ....................................................................................................7 2.2. Device Capabilities..........................................................................................................9 2.3. Test Configuration ...........................................................................................................9 2.4. EMI Suppression Device(s)/Modifications .......................................................................9 2.5. Labeling Requirements ...................................................................................................9 2.6. Test Software ..................................................................................................................9 3. DESCRIPTION OF TEST .........................................................................................................10 3.1.Evaluation Procedure ....................................................................................................10 3.2. AC Line Conducted Emissions......................................................................................10 3.3. Radiated Emissions....................................................................................................... 11 4. ANTENNA REQUIREMENTS ..................................................................................................12 5. TEST EQUIPMENT CALIBRATION DATE ..............................................................................13 6. MEASUREMENT UNCERTAINTY ...........................................................................................14 7. TEST RESULT .........................................................................................................................15 7.1.Summary .......................................................................................................................15 7.2.6dB Bandwidth Measurement .......................................................................................16 7.2.1. Test Limit ...................................................................................................................16 7.2.2. Test Procedure used .................................................................................................16 7.2.3. Test Setting................................................................................................................16 7.2.4. Test Setup .................................................................................................................16 7.2.5. Test Result.................................................................................................................17 7.3. Output Power Measurement .........................................................................................21 7.3.1. Test Limit ...................................................................................................................21 7.3.2. Test Procedure Used .................................................................................................21 7.3.3. Test Setting................................................................................................................21 7.3.4. Test Setup .................................................................................................................21 7.3.5. Test Result of Output Power......................................................................................22 7.4. Power Spectral Density Measurement ..........................................................................24 7.4.1. Test Limit ...................................................................................................................24 Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 4 of 74 7.4.2.Test Procedure Used .................................................................................................24 7.4.3. Test Setting................................................................................................................24 7.4.4. Test Setup .................…

Text truncated - open the document above for the full version.

Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 38 of 74 Channel 06 (2437MHz) 100kHz PSD reference Level Spurious Emission 30MHz ~ 25GHz Channel 09 (2452MHz) 100kHz PSD reference Level High Band Edge Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 39 of 74 Spurious Emission 30MHz ~ 25GHz BLE Out-of-Band Emissions Channel 00 (2402MHz) 100kHz PSD reference Level Low Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 40 of 74 Channel 19 (2440MHz) 100kHz PSD reference Level Spurious Emission 30MHz ~ 25GHz Channel 39 (2480MHz) 100kHz PSD reference Level High Band Edge Spurious Emission 30MHz ~ 25GHz Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 41 of 74 7.6. Radiated Spurious Emission Measurement 7.6.1. Test Limit All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table per Section 15.209. FCC Part 15 Subpart C Paragraph 15.209 Frequency [MHz] Field Strength [V/m] Measured Distance [Meters] 0.009 - 0.490 2400/F (kHz) 300 0.490 - 1.705 24000/F (kHz) 30 1.705 - 30 30 30 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 7.6.2. Test Procedure Used KDB 558074 D01v03r02 - Section 12.2.3 (quasi-peak measurements) KDB 558074 D01v03r02 - Section 12.2.4 (peak power measurements) KDB 558074 D01v03r02 - Section 12.2.5 (average power measurements) 7.6.3. Test Setting 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest Peak Field Strength Measurements per Section 12.2.4 of KDB 558074 D01v03r02 2. RBW = as specified in Table 1 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 42 of 74 6. Trace mode = max hold 7. Trace was allowed to stabilize Table 1 - RBW as a function of frequency Frequency RBW 9 ~ 150 kHz 200 ~ 300 Hz 0.15 ~ 30 MHz 9 ~ 10 kHz 30 ~ 1000 MHz 100 ~ 120 kHz > 1000 MHz 1 MHz 1. RBW = 1MHz. Average Field Strength Measurements per Section 12.2.5.1 of KDB 558074 D01v03r02 2. VBW ≥ 3 x RBW. 3. Detector = RMS, if span/(# of points in sweep) ≤ (RBW/2). Satisfying this condition may require increasing the number of points in the sweep or reducing the span. If this condition cannot be satisfied, then the detector mode shall be set to peak. 4. Averaging type = power (i.e., RMS).  As an alternative, the detector and averaging type may be set for linear voltage averaging.  Some instruments require linear display mode in order to use linear voltage averaging. Log or dB averaging shall not be used. 5. Sweep time = auto. 6. Perform a trace average of at least 100 traces. Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 43 of 74 7.6.4. Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 44 of 74 1GHz ~ 25GHz Test Setup: Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 45 of 74 7.6.5. Test Result Te s t Mode: 802.11b Test Site: AC1 Test Channel: 06 Test Engineer: Roy Cheng Remark: 1. Average measurement was not performed if peak level lower than average limit. 2. The worst case of Radiated Spurious Emission. 3. Other frequency was 20dB below limit line within 1-18GHz, there is not show in the report. Mark Frequency (MHz) Reading Level (dBμV) Factor (dB) Measure Level (dBμV/m) Limit (dBμV/m) Margin (dB) Detector Polarization * 3026.4 35.9 3.4 39.3 74.2 -34.9 Peak Horizontal * 3563.3 35.8 4.1 39.9 74.2 -34.3 Peak Horizontal 4874.0 36.4 6.6 43.0 74.0 -31.0 Peak Horizontal 7311.0 34.0 14.0 48.0 74.0 -26.0 Peak Horizontal * 3024.3 35.6 3.4 39.0 74.2 -35.2 Peak Vertical * 3547.9 35.2 4.1 39.3 74.2 -34.9 Peak Vertical 4874.0 35.5 6.6 42.1 74.0 -31.9 Peak Vertical 7311.0 34.2 14.0 48.2 74.0 -25.8 Peak Vertical Note 1: “*” is not in restricted band, its limit is 20dBc of the fundamental emission level (94.2dBμV/m). Note 2: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 46 of 74 Te s t Mode: BLE Test Site: AC1 Test Channel: 00 Test Engineer: Roy Cheng Remark: 1. Average measurement was not performed if peak level lower than average limit. 2. The worst case of Radiated Spurious Emission. 3. Other frequency was 20dB below limit line within 1-18GHz, there is not show in the report. Mark Frequency (MHz) Reading Level (dBμV) Factor (dB) Measure Level (dBμV/m) Limit (dBμV/m) Margin (dB) Detector Polarization * 3063.5 36.2 3.5 39.7 70.1 -30.4 Peak Horizontal * 3524.2 36.2 3.9 40.1 70.1 -30.0 Peak Horizontal 4804.0 37.1 6.4 43.5 74.0 -30.5 Peak Horizontal 7206.0 34.4 13.6 48.0 74.0 -26.0 Peak Horizontal * 3048.4 36.0 3.4 39.4 70.1 -30.7 Peak Vertical * 3542.7 34.7 4.0 38.7 70.1 -31.4 Peak Vertical 4804.0 36.3 6.4 42.7 74.0 -31.3 Peak Vertical 7206.0 34.7 13.6 48.3 74.0 -25.7 Peak Vertical Note 1: “*” is not in restricted band, its limit is 20dBc of the fundamental emission level (90.1dBμV/m). Note 2: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 47 of 74 The worst case of Radiated Emission below 1GHz: Engineer: Milo Li Site: AC1 Time: 2014/10/08 - 11:58 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: VULB9162_0.03-8GHz Polarity: Horizontal EUT: 10.1”PAD Power: AC 120V/60Hz Worst Case Mode: 802.11b at channel 2437MHz No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Over Limit (dB) Limit (dBuV/m) Factor (dB) Type 1 128.455 21.351 11.425 -22.149 43.500 9.926 QP 2 * 868.565 28.161 5.096 -17.839 46.000 23.065 QP Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) Report No.: 1409RSU04601 FCC ID: ROU00010 Page Number: 48 of 74 Engineer: Milo Li Site: AC1 Time: 2014/10/08 - 12:01 Limit: FCC_Part…

Text truncated - open the document above for the full version.

Test Setup Photo Description: Front View of the Conducted Emission Test Setup Description: Back View of the Conducted Emission Test Setup Description: Front View of the Conducted Emission Test Setup Description: Back View of the Conducted Emission Test Setup Description: Radiated Emission Test Setup for 9kHz ~ 30MHz Description: Radiated Emission Test Setup for 30MHz ~ 1GHz Description: Radiated Emission Test Setup for 30MHz ~ 1GHz Description: Radiated Emission Test Setup for 1GHz ~ 18GHz Description: Radiated Emission Test Setup for 1GHz ~ 18GHz Description: Radiated Emission Test Setup for 18GHz ~ 25GHz