RPV-GW51W-MAXIWireless Serial Server

Atop ABLELink Serial-Ethernet Server GW51W-MAXI User Manual Version 1.0 Updated on 2004/04/08 Tel: 886-3-5508137 Fax: 886-3-5508131 www.atop.com.tw User manual Version 1.0 ABLELink Serial-Ethernet Server GW51W-MAXI Copyright © 2003 Atop Technologies, Inc. All rights reserved. Designed in Taiwan. 1 / 54 IMPORTANT ANNOUNCEMENT The information contained in this document is the property of Atop Technologies, Inc. and is supplied for the sole purpose of the operation and maintenance of products of Atop Technologies, Inc. No part of this publication is to be used for any other purposes, and it is not to be reproduced, copied, disclosed, transmitted, stored in a retrieval system, or translated into any human or computer language, in any form, by any means, in whole or in part, without the prior express written consent of Atop Technologies, Inc. Published by Atop Technologies, Inc. 2F, No. 146, Sec. 1, Tung-Hsing Rd. Jubei City, Hsinchu 302 Taiwan, R.O.C. Tel: 886-3-5508137 Fax: 886-3-5508131 www.atop.com.tw Copyright © 2003 Atop Technologies, Inc. All rights reserved. All other product names referenced herein are registered trademarks of their respective companies. User manual Version 1.0 ABLELink Serial-Ethernet Server GW51W-MAXI Copyright © 2003 Atop Technologies, Inc. All rights reserved. Designed in Taiwan. 2 / 54 FCC WARNING Class B for Serial-Ethernet Server (Model GW51W-MAXI) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference is a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is guarantee the interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna, - Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio / TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Use only shielded cables to connect other devices to this equipment by RS-232 / RS-485 ports. Be cautioned that changes or modifications not approved by the party responsible for compliance could void your authority to operate the equipment. ATOP declared that GW51W-MAXI is limited in ch1~ch11 by specified firmware controlled in USA. User manual Version 1.0 ABLELink Serial-Ethernet Server GW51W-MAXI Copyright © 2003 Atop Technologies, Inc. All rights reserved. Designed in Taiwan. 3 / 54 CONTENTS CONTENT........................................................................................................3 1. INTRODUCTION..........................................................................................5 1.1 PACKAGING.........................................................................................................................5 1. 2 APPLICATION CONNECTIVITY...............................................................................................6 2. NOMENCLATURE AND SETTINGS...........................................................8 2.1 NOMENCLATURE OF GW51W-MAXI COMPONENTS...............................................................8 2.2 MODE SWITCH...................................................................................................................8 3. HARDWARE INSTALLATION.....................................................................9 3.1 CONFIGURATION..................................................................................................................9 3.2 ASSIGNING A NEW IP ADDRESS BY ARP COMMAND................................................................9 3.3 TCP/IP PORT NUMBER......................................................................................................10 4. SOFTWARE CONFIGURATION................................................................11 4.1 CONFIGURATION SET BY MONITOR.EXE UTILITY....................................................................11 4.2 CONFIGURATION SET BY TELNET UTILITY.............................................................................11 4.3 CONFIGURATION SET BY HYPER TERMINAL CONSOLE UTILITY................................................23 4.4 CONFIGURATION SET BY WEB BROWSER..............................................................................24 4.5 VIRTUAL COM MODE.........................................................................................................30 4.5.1 Setup of a Virtual COM driver.................................................................................30 4.5.2 Virtual COM communication...................................................................................31 5. SNMP SETUP............................................................................................35 5.1 SNMP NETWORK MANAGEMENT PL…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

(Fig. 1) FCC ID: RPV-GW51W-MAXI LABEL LOCATION Label

GW51W-MAXI.jpg (1809x2079x16M jpeg)

Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9

FCC ID: RPV-GW51W-MAXI Report No. RF920605H05B Operational Description This device is a Wireless Serial Server which operates in 2.4 GHz band with DSSS technique. The transmitter of the EUT is powered by AC adapter. The antenna is Dipole antenna with SMA Reversed Connector. Under normal use condition, the user has to keep at least 20 cm separation distance between radiator and the body of the user. For more detailed instruction, please refer to the user’s manual. DSSS Information Direct Sequence Spread Spectrum, the data is mixed by pseudorandom code which is an orthogonal code. The mixed data is digital modulated by BPSK and QPSK technique depends on the data rates. The CCK coding is applied for increasing the data rate, and also the processing gain will be increased. The bit rates are 1,2,5.5,11Mbps, the symbol rates are 1,1,1.375,1.375Mbps, the chip rates are always 11Mbps. So, the Chip/symbol is 11,11,8 and 8 respectively. Although is higher bit rate, the processing gain is lower than 10, but the CCK coding used in higher bit rate will provide 2.2dB coding gain.

FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B 1 RF EXPOSURE REPORT REPORT NO.:RF920605H05B MODEL NO.: GW51W-MAXI ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: ATOP TECHNOLOGIES, INC. ADDRESS: 3F, No.8, Prosperity Rd.II, Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B 2 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification This device is not fixed inside the host equipment, it is connected with host through wire. So it is easy to be re-located in the place where at least 20 cm far away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device. FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B 4 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber are 2.0dBi or 1.585 (numeric). 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: FOR DSSS: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241226.30270.008291.0 6243728.18380.008891.0 11246221.13490.006661.0

FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B1Issued: Mar. 08, 2004 FCC TEST REPORT REPORT NO.: RF920605H05B MODEL NO.: GW51W-MAXI RECEIVED: Nov. 27, 2003 TESTED: Nov. 27 to Dec. 16, 2003 APPLICANT: ATOP TECHNOLOGIES, INC. ADDRESS: 3F, No.8, Prosperity Rd.II, Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C ISSUED BY:Advance Data Technology Corporation LAB LOCATION:No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 45 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The test results in the report only apply to the tested sample. 0536 ILAC MRA FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B2Issued: Mar. 08, 2004 Table of Contents 1CERTIFICATION........................................................................................... 4 2SUMMARY OF TEST RESULTS .................................................................. 5 3GENERAL INFORMATION ........................................................................... 6 3.1GENERAL DESCRIPTION OF EUT ............................................................. 6 3.2DESCRIPTION OF TEST MODES ............................................................... 7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS............................... 7 3.4DESCRIPTION OF SUPPORT UNITS ......................................................... 8 4TEST TYPES AND RESULTS ...................................................................... 9 4.1CONDUCTED EMISSION MEASUREMENT................................................ 9 4.1.1 TEST INSTRUMENTS ............................................................................................9 4.1.2 TEST PROCEDURES ..........................................................................................10 4.1.3 DEVIATION FROM TEST STANDARD .................................................................10 4.1.4 TEST SETUP........................................................................................................ 11 4.1.5 EUT OPERATING CONDITIONS..........................................................................12 4.1.6 TEST RESULTS ...................................................................................................13 4.2RADIATED EMISSION MEASUREMENT................................................... 15 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ...........................................15 4.2.2 TEST INSTRUMENTS ..........................................................................................16 4.2.3 TEST PROCEDURES ..........................................................................................17 4.2.4 DEVIATION FROM TEST STANDARD .................................................................17 4.2.5 TEST SETUP........................................................................................................18 4.2.6 EUT OPERATING CONDITIONS..........................................................................18 4.2.7 TEST RESULTS ...................................................................................................19 4.36dB BANDWIDTH MEASUREMENT .......................................................... 23 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ..................................................23 4.3.2 TEST INSTRUMENTS ..........................................................................................23 4.3.3 TEST PROCEDURE.............................................................................................24 4.3.4 DEVIATION FROM TEST STANDARD .................................................................24 4.3.5 TEST SETUP........................................................................................................24 4.3.6 EUT OPERATING CONDITIONS..........................................................................24 4.3.7 TEST RESULTS ...................................................................................................25 4.4MAXIMUM PEAK OUTPUT POWER.......................................................... 29 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT .....................29 4.4.2 INSTRUMENTS....................................................................................................29 4.4.3 TEST PROCEDURES ..........................................................................................30 4.4.4 TEST SETUP........................................................................................................30 4.4.5 EUT OPERATING CONDITIONS..........................................................................30 4.4.6 TEST RESULTS ...................................................................................................31 FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B3Issued: Mar. 08, 2004 4.4.7 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..............................32 4.4.8 TEST INSTRUMENTS ..........................................................................................32 4.4.9 TEST PROCEDURE.............................................................................................33 4.4.10 DEVIATION FROM TEST STANDARD .................................................................33 4.4.11 TEST SETUP........................................................................................................33 4.4.12 EUT OPERATING CONDITION ............................................................................33 4.4.13 TEST RESULTS ...................................................................................................34 4.5BAND EDGES MEASUREMENT ............................................................... 38 4.5.1 LIMITS OF BAND EDGES MEASUREMENT........................................................38 4.5.2 TEST INSTRUMENTS .................................................................…

Text truncated - open the document above for the full version.

Report No. RF920605H05B 1 The Measurement of Conducted Spurious Emissions CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 1. LIMITS OF CONDUCTED SPURIOUS EMISSIONS EASUREMENT Below 20dB of the highest emission level of operating band (in 100KHz Resolution Bandwidth, see Section 15.247(c)). Emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the limits specified in Section 15.209(a) (see Section 15.205(c)). 2. TEST INSTRUMENTS Description & ManufacturerModel No.Serial No.Calibrated Until R&S SPECTRUM ANALYZERFSP40100037May. 06, 2004 High pass filter 2.4G WHK3.1/18G- 10SS SN4Jun. 12, 2004 NOTE: 1.The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 3. TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 kHz bandwidth from band edge. The band edges was measured and recorded. Report No. RF920605H05B 2 4. TEST SETUP 5. EUT OPERATING CONDITIONS The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. EUT SPECTRUM ANALYZER Report No. RF920605H05B 3 TEST RESULTS – For 802.11b The spectrum plots are attached on the following 2 pages. It shows compliance with the requirement in part 15.247(C),.15.205 and 15.209. Report No. RF920605H05B 4 Ch1 Report No. RF920605H05B 5 Ch11

FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B43Issued: Mar. 08, 2004 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: RPV-GW51W-MAXI Report No.: RF920605H05B44Issued: Mar. 08, 2004 RADIATED EMISSION TEST