
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
β 1 This device conforms to FCC Part 15. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. 2 User should not change or modify this device in any ways. The change or modification may be causes cancellation of userβs right to use this device and the warranty to user without explicit consent of the party responsible for complying with this regulation. 3 To avoid radio interference to authorized service, this device shall be used in vehicle so as to get maximum protection. 4 This device conforms to Directive R&TTE of May 1995 of European Community and is approved to bear CE label. 5 If no proper protection design or electromagnetic compatibility is considered, almost all devices will be affected by electromagnetic interference (EMI). CONTROL PANEL Function Button Volume Button Power on/off MIC earpiece hole Charge hole βββ β β AUTOMATIC CONNECTION: * MANUAL CONNECTION β CANCEL SEARCHING DISCONNECT THE SPEAKER PHONE WITHBLUETOOTH CELL PHONE MAKE A CALL ANSWER A CALL HANGUP CALLSWITCH ADJUST VOLUME Last Number Redial ββ . VOICE TAG INITIATE VOICE DIALING ββ Description to pairing operation for some common phone brands βββ β β ββ βββ β βββ β β Phone models supported by this Bluetooth Speaker phone PHONE MODELS SUPPORTED: β Simple troubleshooting method FAILURE CAUSE ANALYSIS TROUBLESHOOTING METHOD 1 β 2 3 β 4 5 6 7 8 ββ
This confidential document is the property of HAMGSHING Technology Group. and must not be copied or ci rculated without permissi on HAMGSHING TECHNOLOGY GROUP B+ KBT130N-1 Block Diagram B- Speaker MIC Antenna Audio Power Amp MIC Amp Echo Canceller Bluetooth Module Voltage Regulator
Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 1 of 7 PHOTOS OF EUT- Bluetooth Handsfree Kit, Model No.: KBT130N-1 N Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 3 of 7 PHOTOS OF EUT-CASE Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 4 of 7 PHOTOS OF EUT-CASE Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 7 of 7 PHOTOS OF EUT-BATTERY
Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Sample of FCC ID Label The device is large enough for it to be placed warning statement on the device as follow: FCC ID: RQ5KBT130N-1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 2 of 7 PHOTOS OF EUT-TOP Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 5 of 7 PHOTOS OF EUT-PCB Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, R.O.C. Photo Page: 6 of 7 PHOTOS OF EUT-MICROPHONE
This confidential document is the property of HAMGSHING Industry Co., Ltd. and must not be copied or circulated without permission OPERATION DESCRIPTION The Speaker Phone function is realized by using Bluetooth technology. The operating principle is as follows: 1. Press the four buttons to control Bluetooth module. 2. The pairing and link between Bluetooth module and Bluetooth phone are realized under the control of the buttons. 3. Use Bluetooth phone to make a call. The Audio is transferred to Speaker phone through Wireless from Bluetooth phone, to drive the speaker after echo cancellation circuit, operational amplifier and power amplifier. 4. The MIC signal is sent out to phone via operational amplifier, echo cancellation circuit and Bluetooth module. 5. During conversation, the volume of speaker can be adjusted by short press the volume buttons 6. Press Function button, you can answer a incoming call. Press power button to end a conversation/reject a incoming call/power on/power off. 7. Keep your private conversation via the additional headset 8. Internal 1500mAh lithium polymer battery for long talk time one charge cycle. PRODUCT Bluetooth Carkit MODEL NO. KBT130N-1 POWER SUPPLY DC 6V, 550mA-Adapter FREQUENCY BAND 2400MHz~2483.5MHz CARRIER FREQUENCY 83.5MHz NUMBER OF CHANNEL 79 CHANNEL SPACING 1MHz RATED RF OUTPUT POWER 0dBm MODULATION TYPE AFSK MODE OF OPERATION Duplex DUTY CYCLE 50 % BIT RATE OF TRANSMISSION9600bps ANTENNA TYPE Micro Stripe Antenna ANTENNA GAIN -1.97dBi
1 2 3 4 56 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size B Date: 15-Sep-2005 Sheet of File: F:\KBT130N-1\KBT130N-1-1073\KBT130N-1.Ddb Drawn By: SPK_O_P 1 SPK_O_N 2 VCM_AGC 3 VSS_DAC 4 VDD_DAC 5 PWD_ 6 VSS 7 RST_IN 8 VDD_PLL 9 VSS_PLL 10 XTAL_I 11 XTAL_O 12 TEST 13 RTS_SDA 14 CTS_SCL 15 DR 16 DT 17 VDD 18 VSS 19 GPIO(0) 20 GPIO(1) 21 GPIO(2) 22 GPIO(3) 23 GPIO(4) 24 GPIO(5) 25 SCL 26 SDA 27 LRCK FRAM 28 BCLK 29 VDD 30 TX 31 RX 32 VDD_ADC 33 VSS_ADC 34 RB_ADC 35 RT_ADC 36 MIC0_P 37 MIC0_N 38 MIC1_P 39 MIC1_N 40 MIC2_P 41 MIC2_N 42 LINE_IN_P 43 LINE_IN_N 44 BG_REF 45 BG_R 46 LINE_O_P 47 LINE_O_N 48 U4 3V3 C18 C19 PCM_OUT PCM_CLKPCM_SYNC PCM_IN FB4 FB5 3V3 RTSCTSRXDTXD C5 C1 R4 C3 R6 R3 VBAT R2 C7 C6 C8 C2 Ear_phone+ mute SHTDWN 1 BYPASS 2 +IN 3 -IN 4 Vo1 5 VDD 6 GND 7 Vo2 8 U1 C4 FB2 FB3 R39R38 Y1 C46 C47 Ear_phone- R5 12 J2 SP+ SP- C44 A2.5V C42 R37 RST P2.5V C45 R30 C34 2.5V A2.5V C17 C14 C16 C33 R29 C12 C11 C10 R12 R11R10 C13 PCM_OUT PCM_CLK PCM_SYNC PCM_IN C32 C26 C41 C43 C23 C24 R15 2.5V R16 R17 R18 R32R33 2.5V R34 R40 R28 R27R26 R31 R35 BT_RST C15 2.5V TXDRXDCTSRTS C31 C29 R8 R7 2.5V 2.5V KBT130N-1 POWER_CTRL C39 C38 R14 R13 C25 C27 C37 C40 C21 C22 C20 C35 123456 J1 R9 MIC+MIC- SP+Ear_phone+ Ear_phone- VBAT 3V3 C9 R19 Batt_detect B_LED_drivHold_up Vol_UpVol_Dwn PhoneV2.5_EN Liuchuqun 1/2 0.2 12 J3 Low_batt Gnd 1 3V3 2 MISI 3 CLK 4 CSB 5 MISO 6 J4 3V3MOSICLKCSBMISO MISOCSBCLKMOSI A0 1 A1 2 A2 3 GND 4 SDA 5 VCC 8 TEST 7 SCL 6 U3 P2.5V R25 R20R21R22 R23 Q1 R1 C28 C30 GND 1 VDD-PA 2 GND-PA 3 AIO(0) 4 AIO(1) 5 RESET 6 SPI-NISO 7 SPI-CSB 8 SPI-CLK 9 SPI-MOSI 10 UART-CTS 11 UART-TX 12 UART-RTS 13 UART-RX 14 1V8 15 3V3 16 GND 17 GND 34 RF 33 GND 32 PIO(0) 31 PIO(1) 30 PIO(2) 29 PIO(3) 28 PIO(4) 27 PIO(5) 26 PIO(6) 25 PIO(7) 24 USB=DN 23 USB-DP 22 PCM-CLK 21 PCM-IN 20 PCM-SYNC 19 PCM-OUT 18 U2 R36 P2.5V C36 RST FB1 mute RF1 R41 C50 C51 C54 C53 C55 C52 SP- TP8 TP10 TP11 TP9 TP12 TP13 TP15 TP14 TP17 TP18 TP19 TP29TP30 TP31 TP33TP34TP35 TP32 TP38 TP26 TP25 TP27 TP28 TP39 TP40 TP37 TP16 TP20 TP21 TP22 TP23TP24 TP36 1 2 3 4 56 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size B Date: 15-Sep-2005 Sheet of File: F:\KBT130N-1\KBT130N-1-1073\KBT130N-1.Ddb Drawn By: R205 Q202R202 R206 R203 6V 12 J202 LED201 LED202 B_LED_driv VBAT C202 R207 Batt_detect R201 D201 1 2 3 J201 6V C201 6V CE 1 GND 2 NC 3 VDD 4 Vout 5 U202 CE 1 GND 2 NC 3 VDD 4 Vout 5 U203 VBAT C203 C204 3V3 VBAT C205 C206 2.5V FB202 FB201 A2.5V V2.5_EN R208 SW201 VBAT R209R210 2 3 1 D202 R211 POWER_CTRL R212 Hold_up R213R214R215 LED203LED204LED206 SW204SW203SW202 3V3 LED205 Vol_Up Vol_DwnPhone KBT130N-1 0.22/2Liuchuqun Q201 R204 Low_batt P2.5V + C207 + C208 SW205 KBT130~1KBT130~1.SCH CHAR 1 GND 2 BAT 3 VDD 4 PROGM 5 U201 TP1 TP2 TP4 TP6TP7 TP5 TP3
Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:2 of 57 Issued Date: May 22, 2006 Table of Contents 1. DOCUMENT POLICY AND TEST STATEMENT ................................................... 4 1.1 DOCUMENT POLICY ......................................................................................... 4 1.2 TEST STATEMENT ............................................................................................ 4 1.3 EUT MODIFICATION........................................................................................... 4 2. DESCRIPTION OF EUT AND TEST MODE ....................................................... 5 2.1 GENERAL DESCRIPTION OF EUT ................................................................... 5 2.2 DESCRIPTION OF SUPPORT UNIT.................................................................. 6 2.3 DESCRIPTION OF TEST MODE ....................................................................... 6 3. DESCRIPTION OF APPLIED STANDARDS....................................................... 6 4. CONDUCTED EMISSION TEST ......................................................................... 7 4.1 CONDUCTED EMISSION LIMIT ........................................................................ 7 4.2 TEST EQUIPMENT ............................................................................................ 7 4.3 TEST SETUP...................................................................................................... 8 4.4 TEST PROCEDURE........................................................................................... 8 4.5 EUT OPERATING CONDITION.......................................................................... 8 4.6 TEST RESULT.................................................................................................... 9 5 TECHNICAL CHARACTERISTICS TEST............................................................ 12 5.1 CHANNEL SEPARATION TEST....................................................................... 12 5.1.1 LIMIT ................................................................................................................ 12 5.1.2 TEST EQUIPMENT ....................................................................................... 12 5.1.3 TEST SET-UP................................................................................................ 12 4.1.4 TEST PROCEDURE...................................................................................... 12 4.1.5 EUT OPERATING CONDITION..................................................................... 12 5.1.6 TEST RESULT............................................................................................... 13 5.2 20DB BANDWIDTH .......................................................................................... 17 5.2.1 LIMIT ............................................................................................................. 17 5.2.2 TEST EQUIPMENT ....................................................................................... 17 5.2.3 TEST SET-UP................................................................................................ 17 5.2.4 TEST PROCEDURE...................................................................................... 17 5.2.5 EUT OPERATING CONDITION..................................................................... 17 5.2.6 TEST RESULT............................................................................................... 18 5.3 QUANTITY OF HOPPING CHANNEL TEST.................................................... 22 5.3.1 LIMIT ................................................................................................................ 22 5.3.2 TEST EQUIPMENT ....................................................................................... 22 5.3.3 TEST SET-UP................................................................................................ 22 5.3.4 TEST PROCEDURE...................................................................................... 22 5.3.5 EUT OPERATING CONDITION..................................................................... 22 5.3.6 TEST RESULT............................................................................................... 23 5.4 TIME OF OCCUPANCY (DWELL TIME)........................................................... 24 5.4.1 LIMIT ................................................................................................................ 24 5.4.2 TEST EQUIPMENT ....................................................................................... 24 Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:3 of 57 Issued Date: May 22, 2006 5.4.3 TEST SET-UP................................................................................................ 24 5.4.4 TEST PROCEDURE...................................................................................... 24 5.4.5 EUT OPERATING CONDITION..................................................................... 24 5.4.6 TEST RESULT............................................................................................... 25 5.5 PEAK POWER TEST ........................................................................................ 29 5.5.1 LIMIT ................................................................................................................ 29 5.5.2 TEST EQUIPMENT ....................................................................................... 29 5.5.3 TEST SET-UP................................................................................................ 30 5.5.4 TEST PROCEDURE...................................................................................... 30 5.5.5 EUT OPERATIβ¦
Text truncated - open the document above for the full version.
Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:52 of 56 Issued Date: May 22, 2006 7. PHOTOS OF TESTING - Conducted test-Charge Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:53 of 56 Issued Date: May 22, 2006 - Radiated test-RX-Link+Charge Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:54 of 56 Issued Date: May 22, 2006 - Radiated test-TX (30-1000MHz) Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan TEST REPORT Reference No.: A06040606 Report No.: FCCA06040606 FCC ID: RQ5KBT130N-1 Page:55 of 56 Issued Date: May 22, 2006 - Radiated test-TX (1-25GHz)
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.40 GHz - 2.48 GHz | 1.00 mW |

Bluetooth Music Port
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
Bluetooth Speakerphone
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
Bluetooth Hands Free Kit
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter
lRAN Bluetooth H/F
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter