RU4-HWM6505-DWZigbee RF Module

HWM6505-DW ZigBee Door Window Module User Guide HWM6505-DW is a door window sensor with ZigBee RF communication. The home security system is built by a Zigbee networks to combine components as controller panel, sensors, sirens, keyfob, and keypad. It detects open or close status of door or window, and informs system controller by ZigBee. HWM6505-DW ascertains open/close status by a magnet part, when the magnet is close to sensor, it means close; it shows open when the magnet moves away. Features  Small size for easy furnishing  Long-life 3V lithium battery operated  Outstanding communication range  Tamper switch avoids physical attack Specification ZigBee RF Characteristic  RF Protocol: IEEE 802.15.4  RF frequency: 2405MHz~2480MHz  Channel Bandwidth: 5MHz  ZigBee Encryption: AES 128bits Dimension  L41.5 x W11 mm Temperature  Operating: -10ºC ~ 50ºC (32ºF ~ 132ºF)  Storage: -10ºC ~ 60ºC (-4ºF ~ 158ºF) Operating Humidity  10% ~ 85% Non-Condensing Compliance  FCC subpart 15B and subpart 15C  UL/cUL Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE This module is intended for OEM integrator only and limited to inserted to similar host device (Brand: Metalligence and Model: HWS6505-DW) which is battery powered host devices and has a plastic housing without any metal shielding. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT The final end product must be labeled in a visible area with the following "Contains TX FCC ID: RU4-HWM6505-DW". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en comprome…

Text truncated - open the document above for the full version.

Page No. : 20 Limited Module Approval Request Letter Subject: Limited Module Approval Date: 2011/10/12 FCC ID: RU4-HWM6505-DW Dear Reviewer, We, Sporton International Inc., are authorized by Metalligence Technology Corp. to have their state-of-the-art Zigbee Door Window Module approved under limited module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in Public Notice DA00-1407 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The RF module is fixed on the carrier board as documented on the photo exhibits and integrated for measurement purposes in a typical host configuration: Zigbee Door Window Sensors (HWS6505-DW / Metalligence) which has a plastic housing without any metal shielding. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip EM357 QFN-48. 3. The requirement of power supply regulation: No power regulator can provide stability power source. But specific of hosts have 3.3Vdc regulator to provide stability power from host battery. 4. The requirements of section 15.203 and 15.204(C): Fixed onboard chip antenna. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: The RF module is fixed on the carrier board as documented on the photo exhibits and integrated for measurement purposes in a typical host configuration: Zigbee Door Window Sensors (HWS6505-DW / Metalligence) which has a plastic housing without any metal shielding. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature : Name : Leo Huang Job Title : Manager

Report No.: 152613 SPORTON International Inc. PAGE NUMBER : 1 OF 1 TEL : 886-2-2696-2468 ISSUED DATE : Jun. 20, 2011 FAX : 886-2-2696-2255 Note: This module will be installed on PCB board and no any metal or PCB cover environment which is similar as the test setup host situation. Photographs of EUT

Label size: 20mm*15mm

Report No.: 152613 SPORTON International Inc. PAGE NUMBER : 1 OF 2 TEL : 886-2-2696-2468 ISSUED DATE : Jun. 20, 2011 FAX : 886-2-2696-2255 Note: This module will be installed on PCB board and no any metal or PCB cover environment which is similar as the test setup host situation. Photographs of EUT Report No.: 152613 SPORTON International Inc. PAGE NUMBER : 2 OF 2 TEL : 886-2-2696-2468 ISSUED DATE : Jun. 20, 2011 FAX : 886-2-2696-2255 Note: This module will be installed on PCB board and no any metal or PCB cover environment which is similar as the test setup host situation.

Report No.: FR152613 FCC ID: RU4-HWM6505-DW Page No. : B1 of B3 Appendix B. Maximum Permissible Exposure Report No.: FR152613 FCC ID: RU4-HWM6505-DW Page No. : B2 of B3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.25 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR152613 FCC ID: RU4-HWM6505-DW Page No. : B3 of B3 1.3. Calculated Result and Limit Antenna Type : Chip Antenna Max Conducted Power for IEEE 802.15.4 ZigBee: 21.07 dBm Antenna Gain (dBi) Antenna Gain (numeric) Output Power (dBm) Output Power ( mW ) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 2.5 1.7783 21.0700 127.9381 0.045285 1 Complies

Report No.: CR152613 IC: 9682A-HWM6505DW Page No. : 1 of 4 Appendix A. Test Photos Report No.: CR152613 IC: 9682A-HWM6505DW Page No. : 2 of 4 1. Photographs of Radiated Emissions Test Configuration Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: CR152613 IC: 9682A-HWM6505DW Page No. : 3 of 4 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: CR152613 IC: 9682A-HWM6505DW Page No. : 4 of 4 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW