RV7-CONNWireless Mesh Wide Area Network CPE

27 | Appendix B Regulatory Information Appendix B: Regulatory inf ormation Federal Communications Commission (FCC) compliance notices This section includes the following FCC statements for the CONN-1000-A, SP-4700-A and related SecureMesh™ and SkyPilot by Trilliant Connectors: • FCC ID: RV7-CONN (Applies to CONN-1000-A and SP-4700-A) • Class A Interference Statement • RF Radiation Exposure and Hazard Warning • Non-Modification Statement • Deployment Statement Class A Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure & Hazard Statement To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Non-Modification Statement Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the CONN-1000-A or SP-4700-A and related SecureMesh™ and SkyPilot by Trilliant Connectors and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in the United States. Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands The CONN-1000-A has been prohibited from operating in the 5600 to 5650 MHz frequency band for the US and Canada in order to comply with the DFS requirements as outlined in the FCC Part 15, Subpart E rules. 28 | Appendix B Regulatory Information Canadian IC Statements IC: 0628A-CONN (Applies to CONN-1000-A and SP-4700-A). This device complies with ICES-003 and RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme aux normes NMB003 et CNR-210 d’Industrie Canada. 1. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 2. il ne doit pas produire de brouillage et l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. RF Radiation Exposure & Hazard Statement To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Exposition aux radiations RF & Mention de danger Pour assurer la conformité avec les exigences RSS-102 d'exposition aux RF (Radio Fréquences), cet appareil doit être installé dans un endroit ou l'antenne de l'appareil sera située à une distance de plus de 20 cm (8 po) de toutes personnes. L’utilisation d'antennes à gain plus élevé et les types d'antennes qui ne sont pas couverts en vertu de la certification IC de ce produit n'est pas autorisée. Les installateurs de la radio et les utilisateurs du produit final doivent se conformer aux instructions d'installation fournies dans ce manuel. Cet émetteur ne doit pas être co-implanté ou exploité en conjonction avec toute autre antenne ou transmetteur. Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in Canada. Déclaration de déploiement Ce produit est certifié pour le déploiement à l'intérieur tout en rencontrant les limites de cette bande de fréquences: 5150 - 5250 MHz. Ne pas installer ou utiliser ce produit à l'extérieur au Canada, si cette bande de fréquences ne peut ne peut être rencontrée. 29 | Appendix B Regulatory Information SAFETY INFORMATION Hazard Warning! High Voltage. This situation or condition can cause injury due to electr…

Text truncated - open the document above for the full version.

SecureMesh Connector Installation CONN-1000 © 2011 Trilliant, Inc. All rights reserved This publication, or parts thereof, may not be reproduced in any form, by any method, for any purpose. Product specifications are subject to change without notice. This material is provided for informational purposes only; Trilliant assumes no liability related to its use and expressly disclaims any implied warranties of merchantability or fitness for any particular purpose. Trilliant Trademarks Trilliant™, CellReader®, CellGateway™, SecureMesh™, SerViewCom®, UnitySuite™, SkyPilot®, SyncMesh™, the Trilliant logo, and the SkyPilot logo are trademarks of Trilliant Incorporated and/or its subsidiaries. All other trademarks are the property of their respective owners. This material is provided for informational purposes only; Trilliant assumes no liability related to its use and expressly disclaims any implied warranties of merchantability or fitness for any particular purpose. All specifications, descriptions, and information contained herein are subject to change without prior notice. Third-Party Trademarks Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. MySQL is a registered trademark of MySQL AB in the United States, the European Union, and other countries. All other designated trademarks, trade names, logos, and brands are the property of their respective owners. Third-Party Software Program Credits This product includes software developed by the Apache Software Foundation (http://www.apache.org/), licensed under the Apache License. This product includes the DHCP Server software from Internet Systems Consortium, licensed under the DHCP License. The DHCP Server software is copyright © 2004 Internet Systems Consortium, Inc. (“ISC”). Copyright © 1995–2003 Internet Software Consortium. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of ISC, ISC DHCP, nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY INTERNET SYSTEMS CONSORTIUM AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ISC OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes the FTP Server software from vsftpd (http://vsftpd.beasts.org/ ), licensed under the GNU General Public License. This product includes Java software from Sun Microsystems, licensed under Sun Microsystems' Binary Code License Agreement. Copyright 2003, Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Sun, Sun Microsystems, the Sun logo, Solaris, Java, the Java Coffee Cup logo, J2SE, and all trademarks and logos based on Java are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. This product includes JBOSS Version 3.2.3 software from JBoss, licensed under the GNU Lesser General Public License. Some bundled products in JBOSS are licensed under the Apache License. This product contains Java Telnet Application (JTA 2.0). This product contains the MibBrowser software from Mibble. This product includes software the copyright of which is owned by and licensed from MySQLAB. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/ ). Copyright (c) 1998–2005 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/ )” 4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected]. 5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”. THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR…

Text truncated - open the document above for the full version.

MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com the wireless lab 4 May 2012 Trilliant Networks CONN-1000-A & SP4700-A External Photos EUT Top Page 2 of 6 the wireless lab EUT Bottom Page 3 of 6 the wireless lab EUT side 1 Page 4 of 6 the wireless lab EUT Side 2 Page 5 of 6 the wireless lab EUT Side 3 Page 6 of 6 the wireless lab EUT Side 4

5 GHz Radio Model: CONN ‐ 1000 ‐ R Orderable Part #: AL ‐ 0249R ‐ 1.0 Alternative Region Labels SecureMesh™ Connector CONN ‐ 1000 5 GHz Radio Model: CONN ‐ 1000 ‐ A FCC ID: RV7 ‐ CONN IC ID: 6028A ‐ CONN Orderable Part #: AL ‐ 0249A ‐ 1.0 Rated NEMA ‐ 4X & IP66 Made in Taiwan 48 VDC 0.6A (0,6A) www.trilliantinc.com 501 ‐ 00063 ‐ 01 rev. C

5 GHz Radio Model: SP ‐ 4700 ‐ R Orderable Part #: 726 ‐ 00225 ‐ 01R Alternative Region Labels SkyPilot Connector SP ‐ 4700 5 GHz Radio Model: SP ‐ 4700 ‐ A FCC ID: RV7 ‐ CONN IC ID: 6028A ‐ CONN Orderable Part #: 726 ‐ 00025 ‐ 01R Rated NEMA ‐ 4X & IP66 Made in Taiwan 48 VDC 0.6A (0,6A) www.trilliantinc.com R1.0

MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com the wireless lab 8 May 2012 Trilliant Networks CONN-1000-A & SP4700-A Internal Photos Installation view Page 2 of 9 the wireless lab Page 3 of 9 the wireless lab Main assy moved from Unit Page 4 of 9 the wireless lab Main Assy with RF card Page 5 of 9 the wireless lab Main Assy bottom Page 6 of 9 the wireless lab Main Assy Top 2 Page 7 of 9 the wireless lab RF Assy bottom Page 8 of 9 the wireless lab RF Assy with shield Page 9 of 9 the wireless lab RF Assy with shield removed

Maximum Permissible Exposure FCC, Part 15 Subpart C §15.407(f) Industry Canada RSS-Gen §5.5 Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm 2 ) = EIRP/(4πd 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) The Trilliant CONNECTOR has a single transmitter. Because the EUT belongs to the General Population/Uncontrolled Exposure the limit of power density is 1.0 mW/cm 2 Freq. Band (MHz) Antenna Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Safe Distance @ 1mW/cm 2 Limit(cm) Minimum Separation Distance (cm) 5150 - 5250 17.0 50.1 +4.52 2.83 3.36 20.00 Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Specification Maximum Permissible Exposure Limits FCC §1.1310 Limit = 1mW / cm 2 from 1.310 Table 1 RSS-Gen §5.5 Before equipment certification is granted, the application requirements of RSS-102 shall be met. Laboratory Measurement Uncertainty for Power Measurements Measurement uncertainty ±1.33 dB

COVER PAGE Test of CONN-1000-A This covers the following Product Series: CONN-1000, CONN-1000-W To: FCC 47 CFR Part 15.407 & IC RSS-210 Test Report Serial No.: TRIL05-U3 Rev B TITLE PAGE TEST REPORT FROM Test of CONN-1000-A This covers the following Product Series: CONN-1000, CONN-1000-W To FCC 47 CFR Part 15.407 & IC RSS-210 Test Report Serial No.: TRIL05-U3 Rev B Note: this report contains data with regard to the 5,150 to 5,250 MHz band for Trilliant Connector Wireless LAN Access Point. 5.8 GHz test data is reported in MiCOM Labs test report TRIL05-U1. This report supersedes TRIL05-U3 Rev A Applicant: Trilliant Networks, Inc 1100 Island Drive Redwood City CA 94065 Product Function:SecureMesh TM Wireless WAN 5 GHz Mesh Backhaul Copy No: pdf Issue Date: 17th May 2012 This Test Report is Issued Under the Authority of; MiCOM Labs, Inc. 440 Boulder Cour t, Suite 200 Pleasanton, CA 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com TEST CERTIFICATE #2381.01 MiCOM Labs is an ISO 17025 Accredited Testing Laboratory This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. Title: CONN-1000-A To: Serial #: Issue Date: Page: FCC 47 CF R Part 15.407 & IC RSS-210 TRIL05-U3 Rev B 17th May 2012 3 of 62 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com This page has been left intentionally blank Title: CONN-1000-A To: Serial #: Issue Date: Page: FCC 47 CF R Part 15.407 & IC RSS-210 TRIL05-U3 Rev B 17th May 2012 4 of 62 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs p ersonnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com TABLE OF CONTENTS ACCREDITATION, LISTINGS & RECOGNITION............................................................ 5 TESTING ACCREDITATION.............................................................................................. 5 RECOGNITION................................................................................................................... 6 PRODUCT CERTIFICATION.............................................................................................. 7 1. ................................................................................... 9 TEST RESULT CERTIFICATE 2. ........................................ 10 REFERENCES AND MEASUREMENT UNCERTAINTY 2.1. ............................................................................................. 10 Normative References 2.2. ............................................................................ 11 Test and Uncertainty Procedures 3. .......................................... 12 PRODUCT DETAILS AND TEST CONFIGURATIONS 3.1. ..................................................................................................... 12 Technical Details 3.2. ............................................................................................ 13 Scope of Test Program 3.3. ............................................................. 15 Equipment Model(s) and Serial Number(s) 3.4. ....................................................................................................... 15 Antenna Details 3.5. .............................................................................................. 15 Cabling and I/O Ports 3.6. .................................................................................................. 16 Test Configurations 3.7. .......................................................................................... 17 Equipment Modifications 3.8. .......................................................................... 17 Deviations from the Test Standard 3.9. ............................................................. 17 Subcontracted Testing or Third Party Data 4. ...................................................................................................... 18 TEST SUMMARY 5. ........................................................................................................ 20 TEST RESULTS 5.1. ............................................................................................. 20 Device Characteristics 5.1.1. ........................................................................ 20 26 dB and 99 % Bandwidth 5.1.2. ............................................................................... 25 Transmit Output Power 5.1.3. ..................................................................... 30 Peak Power Spectral Density 5.1.4. ................................................................................. 35 Peak Excursion Ratio 5.1.5. ..................................................................................... 40 Frequency Stability 5.1.6. ................................................................ 41 Maximum Permissible Exposure 5.1.7. .................................................................................... 42 Radiated Emissions 5.1.8. ............................ 55 AC Wireline Conducted Emissions (150 kHz – 30 MHz) 6. ....................................................................................................... 58 PHOTOGRAPHS 6.1. ..................................................... 58 Radiated Test Setup Below 1 GHz - Test Setup 6.2. ...................................................... 59 Radiated Emissions Above 1 GHz - Test Setup 6.3. .............................................................................................. 60 ac Wireline Emissions 7. .........................................................…

Text truncated - open the document above for the full version.

COVER PAGE Test of SP-4700-A This covers the following Product Series: SP-4700, SP-3800 To: FCC 47 CFR Part 15.407 & IC RSS-210 Test Report Serial No.: TRIL05-U4 Rev B TITLE PAGE TEST REPORT FROM Test of SP-4700-A This covers the following Product Series: SP-4700, SP-3800 To FCC 47 CFR Part 15.407 & IC RSS-210 Test Report Serial No.: TRIL05-U4 Rev B Note: this report contains data with regard to the 5,150 to 5,250 MHz band for Trilliant Connector Wireless LAN Access Point. 5.8 GHz test data is reported in MiCOM Labs test report TRIL05-U2. This report supersedes TRIL05-U4 Rev A Applicant: Trilliant Networks, Inc 1100 Island Drive Redwood City CA 94065 Product Function:SkyPilot by Trilliant Wireless WAN 5 GHz Mesh Backhaul Copy No: pdf Issue Date: 17th May 2012 This Test Report is Issued Under the Authority of; MiCOM Labs, Inc. 440 Boulder Cour t, Suite 200 Pleasanton, CA 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com TEST CERTIFICATE #2381.01 MiCOM Labs is an ISO 17025 Accredited Testing Laboratory This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. Title: SP-4700-A To: Serial #: Issue Date: Page: FCC 47 CF R Part 15.407 & IC RSS-210 TRIL05-U4 Rev B 17th May 2012 3 of 62 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com This page has been left intentionally blank Title: SP-4700-A To: Serial #: Issue Date: Page: FCC 47 CF R Part 15.407 & IC RSS-210 TRIL05-U4 Rev B 17th May 2012 4 of 62 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs p ersonnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com TABLE OF CONTENTS ACCREDITATION, LISTINGS & RECOGNITION............................................................ 5 TESTING ACCREDITATION.............................................................................................. 5 RECOGNITION................................................................................................................... 6 PRODUCT CERTIFICATION.............................................................................................. 7 1. ................................................................................... 9 TEST RESULT CERTIFICATE 2. ........................................ 10 REFERENCES AND MEASUREMENT UNCERTAINTY 2.1. ............................................................................................. 10 Normative References 2.2. ............................................................................ 11 Test and Uncertainty Procedures 3. .......................................... 12 PRODUCT DETAILS AND TEST CONFIGURATIONS 3.1. ..................................................................................................... 12 Technical Details 3.2. ............................................................................................ 13 Scope of Test Program 3.3. ............................................................. 15 Equipment Model(s) and Serial Number(s) 3.4. ....................................................................................................... 15 Antenna Details 3.5. .............................................................................................. 15 Cabling and I/O Ports 3.6. .................................................................................................. 16 Test Configurations 3.7. .......................................................................................... 17 Equipment Modifications 3.8. .......................................................................... 17 Deviations from the Test Standard 3.9. ............................................................. 17 Subcontracted Testing or Third Party Data 4. ...................................................................................................... 18 TEST SUMMARY 5. ........................................................................................................ 20 TEST RESULTS 5.1. ............................................................................................. 20 Device Characteristics 5.1.1. ........................................................................ 20 26 dB and 99 % Bandwidth 5.1.2. ............................................................................... 25 Transmit Output Power 5.1.3. ..................................................................... 30 Peak Power Spectral Density 5.1.4. ................................................................................. 35 Peak Excursion Ratio 5.1.5. ..................................................................................... 40 Frequency Stability 5.1.6. ................................................................ 41 Maximum Permissible Exposure 5.1.7. .................................................................................... 42 Radiated Emissions 5.1.8. ............................ 55 AC Wireline Conducted Emissions (150 kHz – 30 MHz) 6. ....................................................................................................... 58 PHOTOGRAPHS 6.1. ..................................................... 58 Radiated Test Setup Below 1 GHz - Test Setup 6.2. ...................................................... 59 Radiated Emissions Above 1 GHz - Test Setup 6.3. .............................................................................................. 60 ac Wireline Emissions 7. .....................................................................…

Text truncated - open the document above for the full version.

MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com the wireless lab 4 May 2012 Trilliant Networks CONN-1000-A & SP4700-A Test Setup Photos Radiated Emissions below 1 GHz - Test Setup Page 2 of 3 the wireless lab Radiated Emissions Above 1 GHz - Test Setup Page 3 of 3 the wireless lab ac Wireline Emissions