RVGEBU236ELECTRONIC BALLAST

User Manual Input Electronic ballast output Volt: 120V ~ 277V, 60Hz Lamp types: Also Compatible with(1) or (2) 36W 4-Pin Quad or Triple Lamps; (1) or (2) 32W 4-Pin Quad or Triple Lamps; (1) or (2) 26W 4-Pin Quad or Triple Lamps; (1) Long Twin Tube 40W or (2) Long Twin Tube 24/27W; (1) Circline 40W or (2) Circline 20W; (1) 2D 38W or (2) 2D 28W. Wiring: Circuit Description When 120V~270V AC power on, the active circuit component with U1, Q1, L5, and D6 steadying voltage, filtering AC wave and effecting power factor up to 0.98. The VDC is filtered through C14 to output supply, which is working under 60Hz and buildup with U2Q2Q3 L6. Safeguard circuit with C26R14ZD3 prevent from failure when circuit opening, shorting and overloading. Warning Label WARNING Install in accordance with national and local electrical code use 18awg solid copper wire, strip wire to 3/8’’. Only use 4-pin rapid start sockets. Green terminal must be grounded. FCC NOTE The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz FCC Warning Statement for FCC ID Label/DoC Label Requirements This device complies with part 18 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interferenceand (2) This device must accept any interference receivedincluding interference that may cause undesired operation.

Block Diagram 120Vac~277Vac EMI AC/DCAPFCDC DC/ACOutput Input

External Photos 1. Front View 2. Back View

ID Label / Location Info 1. Proposed FCC Label Format FCC ID: RVGEBU236 2. Proposed Label Location on EUT FCC Label

Internal Photos 1. EUT Component View 2. PCB Component View 3. PCB - Solder View

         
  

 
      







 
         

 

  

  


      



      
 
 






      
 
      

      
 
           


  
   
 

FCC TEST REPORT FCC ID : RVGEBU236 Applicant : Shenzhen Feeling Electronics Co.,Ltd. Building L, Jingtie Industry Park, Heao, Henggang, Longgang, Shenzhen, China Equipment Under Test (EUT) : Product description : Electronic Ballast Model No. : EBU236 Standards : FCC Part18 Date of Test : February 12, 2004 Test Engineer : Jimmy Lee Reviewed By :Philo Zhong PERPARED BY: Shenzhen Huatongwei International Inspection Co., Ltd Keji S,12th,Road, Hi-tech Industrial Park, Shenzhen, Guangdong, China FCC Registration Number: 662850 Page 1 of 14 Shenzhen Feeling Electronics Co., Ltd. FCC ID:RVGEBU236 2 Contents Page 1 COVER PAGE..........................................................................................................................................................1 2 CONTENTS..............................................................................................................................................................2 3 TEST SUMMARY....................................................................................................................................................3 4 GENERAL INFORMATION..................................................................................................................................4 4.1 CLIENT INFORMATION............................................................................................................................................4 4.2 GENERAL DESCRIPTION OF E.U.T...........................................................................................................................4 4.3 DETAILS OF E.U.T..................................................................................................................................................4 4.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................4 4.5 STANDARDS APPLICABLE FOR TESTING..................................................................................................................4 4.6 TEST METHODOLOGY.............................................................................................................................................4 4.7 TEST FACILITY........................................................................................................................................................5 4.8 TEST LOCATION......................................................................................................................................................5 5 EQUIPMENT USED DURING TEST...................................................................................................................6 6 CONDUCTED EMISSION TEST..........................................................................................................................7 6.1 TEST EQUIPMENT....................................................................................................................................................7 6.2 TEST PROCEDURE...................................................................................................................................................7 6.3 CONDUCTED TEST SETUP.......................................................................................................................................8 6.4 EUT OPERATING CONDITION.................................................................................................................................8 6.5 CONDUCTED EMISSION LIMITS...............................................................................................................................9 6.6 SPECTRUM ANALYZER............................................................................................................................................9 6.7 FREQUENCY RANGE OF MEASUREMENTS.............................................................................................................10 6.8 CONDUCTED EMISSION TEST RESULT...................................................................................................................10 6.8.1 Measurement Data.....................................................................................................................................10 6.8.2 Conducted Emissions Test Data.................................................................................................................12 7 PHOTOGRAPHS OF TESTING..........................................................................................................................13 7.1 CONDUCTED EMISSION TEST VIEW-FRONT..........................................................................................................13 7.2 CONDUCTED EMISSION TEST VIEW –SIDE............................................................................................................13 8 FCC ID LABEL......................................................................................................................................................14 Page 2 of 14 Shenzhen Feeling Electronics Co., Ltd. FCC ID:RVGEBU236 3 Test Summary Test Test RequirementTest Method Class / SeverityResult Radiated Emission (30MHz to 1GHz) FCC PART 18: 2003ANSI C63.4:1992 Class B N/A Conducted Emission (450KHz to 30MHz) FCC PART 18: 2003ANSI C63.4:1992 Class B PASS Page 3 of 14 Shenzhen Feeling Electronics Co., Ltd. FCC ID:RVGEBU236 4 General Information 4.1 Client Information Applicant: Shenzhen Feeling Electronics Co.,Ltd. Address of Applicant: Building L, Jingtie Industry Park, Heao, Henggang, Longgang, Shenzhen, China 4.2 General Description of E.U.T. Product description: Electronic Ballast Model No.: EBU236 4.3 Details of E.U.T. Power Supply: 120~277VAC / 60Hz 4.4 Description of Support Units The EUT has been tested as an independent unit. 4.5 Standards Applicable for Testing The customer requested FCC tests for an Electronic Ballast. The standards used were FCC Part18. 4.6 Test Methodolog…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Conducted Emission Test View-Front 2. Conducted Emission Test View –Side