RXEWE70APFA Wireless LAN Unit

l To mount on a DIN rail * Do not install a product with a pencil-type antenna in a metal panel as it may result in degradation of radio performance. To install this product in a panel, use and install a magnetic-base antenna outside the panel. <Demounting> l Mounting Magnets n Installation method Magnet (Accessory) Flat-Head Screw (Accessory) Flat-Head Screw  (Accessory) (2) Pull it to the right and lower it  while pressing the spring Insert a spring (1) Hold the part A and insert the tip A Mounting screws for this wireless unit must be tightened with torque of 4.4 to 5.3 in. lb. (0.5 to 0.6 N.m) (3) Mount it on the main unit and clamp it  using screws (M3) DIN Rail (2) Unhitch a tab from the DIN rail (1) Pull the lower part Insert a flat-head screw driver under the lower tab and pull downward WE70-AP LANMODE FA WIRELESS LAN ACCESS POINT POWERWIRELESS <Mounting> DIN Rail (2) Pull the bottom side forwards (1) Hitch a tab on the top to the DIN rail l To mount Using Mounting Bracket Mounting screws for this wireless unit must be tightened with torque of 4.4 to 5.3 in. lb. (0.5 to 0.6 N.m) Mounting screws for this wireless unit must be tightened with torque of 4.4 to 5.3 in. lb. (0.5 to 0.6 N.m) (2) Clamp screws in mounting holes. Mounting Hole Process Drawing (Unit: mm) 108 ±0.1 116 ± 0.1 4-M5 Mounting Bracket (Accessory) Tapping Screw (Accessory) (1) Attach the mounting bracket on accessory magnets which are installed on wireless unit.  (Magnet is attached between mounting bracket and a wireless unit.)  Installation on a control panel requires screw hole drilling. n Specification l Wireless LAN Block (5GHz, 54Mbps; Common in AP/CL) Standards Transmission Type Frequency Range Transmission speed Maximum Transmission  Distance (Clear View) IEEE802.11a Orthogonal Frequency Division Multiplexing (OFDM), Simplex 5150 to 5350MHz (8 channels), 5470 to 5725MHz (11 channels),  5725 to 5825MHz (5 channels) Auto/54/48/36/24/18/12/9/6Mbps (theoretical) Indoors: About 40m (Do not use it outdoors) l Wireless LAN Block (2.4GHz, 11Mbps/54Mbps; Common in AP/CL) Standards Transmission Type Frequency Range Transmission speed Maximum Transmission  Distance (Clear View) IEEE802.11b/IEEE802.11g (Using 802.11b) Direct Sequence Spectrum Spread, Simplex (Using 802.11g) Orthogonal Frequency Division Multiplexing (OFDM), Simplex 2400 to 2483.5MHz (13 channels or 11 channels) (Using 802.11b) Auto/11/5.5/2/1Mbps (theoretical) (Using 802.11g) Auto/54/48/36/24/18/12/9/6Mbps (theoretical) Indoors: About 60m Security Group Communication Transmission Power Antenna OCB AES <128-bit>, WEP (RC4) <64/128/152-bit>, WPA-PSK (with encryption type of AES <128-bit> /TKIP <128-bit>), WOC KEY Comformance to ANY-connection refusal 10mW/MHz or less Dual Band Diversity Antenna SMA Reverse Connector StandardsIEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX) (Use STP LAN cables) RJ-45 x 1 l Common Spec for Wireless LAN Block (Common) l Wired LAN Block (Common) * Use straight cables for connection to PLC or PC. Specification Specification Specification Specification Item Item Item Item Wireless LAN Others l Other Functions Supporting Communication Rate Enhancement Technology Atheros Super AG, Variable Transmission Power (3 Levels: High/Mid/Low), Transmission Load Distribution (Connection Terminal Limiting), 11g Protection, Client-to-Client Wireless Communication Inhibition, Roaming, AP-to-AP bridging, MAC Address Registration Security, SSID Setup Any Access Denial Supporting SYSLOG, Web Browser Setup, Administrator ID Setup, Administrator IP Registration Main Unit Setup Power Current consumption Ambient Operation Temperature Dimensions Weight Web Browser 20.4 to 26.4 VDC (Screwless Terminal Block) 250mA max. 0 to +50 ∞C (With no condensation) 120(W) x 103(D) x 34.5(H)mm (excluding projection) About 360g (Main Unit Only) Specification Item l General Specification (Common) Specification Item Precautions for Safe Use Observe the following precautions when using this product: 1) Dedicated packaging must be used for transportation of this product.Take precautions to prevent excessive vibration or shock on the product or falling of the product. 2) Storage of this product must be within the specified environment. Allow the product to warm up to room temperature for at least 3 hours after it has been stored at -10 degrees C or lower. 3) Use the product within the specified temperature and humidity ranges. 4) Do not use the product under the following environments: • Locations subject to extreme temperature changes resulting in condensation • Locations subject to static electricity, excessive noise, or electric fields • Locations where the product may come into contact with water, oil, or chemicals • Locations where corrosive gases or flammable gases are present • Locations where large amounts of dust or dirt are present • Locations subject to spatters, iron chips, or fillings 5) Do not use it outdoors (outside a control panel). 6) Use tape, cord, or other means to hold the product while adjusting the installation position to prevent the product from damage due to failing. 7) Tighten the mounting screws to the specified torque of 4.4 to 5.3 in lb. (0.5 to 0.6 N.m) 8) Provide sufficient space around the product for heat dissipation. Install the products with a margin of 20mm or longer externally. 9) Do not reverse the power supply connection or connect the product to an AC power supply. 10) Use the correct power supply voltage. 11) Use the solid wire, 26 to 17 AWG for power supply. The exposed length of wire is 10 to 11mm. 12) Do not lay communications cables and antenna cables near other high- voltage cables or power lines. 13) Setup is required after the installation or replacement of this product. Set up the product correctly according to the manual, and be sure to confirm that communication is established before using it. 14) Do not apply excess vibrations or shock to this product. Do not drop this product. 15) Other wireless devices operat…

Text truncated - open the document above for the full version.

Contact Address OMRON ELECTRONICS LLC. After sales Support Engineering Service Department One Commerce Drive, Schaumburg. IL 60173-5302 U.S.A Phone: 1-847-843-7900 Fax: 1-847-843-7787 OMRON ELECTRONICS B.V. Wegalaan 61 2132 JD, HOOFDDORP, THE NETHERLANDS Phone: 31-23-56-81-100 Fax: 31-23-56-81-188 (1) Configure an IP address and a subnet mask for PC. (2) Start a WWW browser. (3) Enter the IP address specified for the wireless unit in the address bar of the WWW browser. Enter http://192.168.0.1/ (factory shipment) for WE70-AP and http://192.168.0.254/ (factory shipment) for WE70-CL, then press [Enter] key. (4) In case of an access point, a password input is requested. Press [Enter] key while leaving the password field blank. (5) A Basic Setup screen of Network Setup menu is displayed at first. * To configure SSID and encryption of wireless LAN from PC connected to a wired LAN,  See "WE70 AP/CL FA Wireless LAN Unit OPERATION MANUAL" (Cat.No.N153-E1). n Initiating Setup Screen n Channel assignment based on frequency band 802.11b/g: All of 13 channels (except 12CH and 13CH in United States) (Up to 3 channels that can be used simultaneously) (MHz) 1CH 2CH 3CH 4CH 5CH 6CH 7CH 8CH 9CH 10CH 11CH 12CH 13CH 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2.4GHz band 802.11a: All of 24 channels (up to 24 channels that can be used simultaneously) globally common, indoors only (MHz)All Countries 36CH 5180 100CH 5500 104CH 5520 108CH 5540 112CH 5560 116CH 5580 120CH 5600 124CH 5620 128CH 5640 132CH 5660 136CH 5680 140CH 5700 40CH 5200 44CH 5220 48CH 5240 52CH 5260 56CH 5280 60CH 5300 64CH 5320 (MHz) 5GHz band (MHz)United States only 149CH 5745 153CH 5765 157CH 5785 161CH 5805 165CH 5825 All Countries except France Cable (AWG 26 to 17) Single Wire 10 to 11 mm Stripping Length n Wiring Precautions • Signal lines and power lines must be separated to avoid influence of noise. • Do not lay cables close to antennas. • Wiring must be done while power is off. • Use a pin terminal and a cable for connection as shown below. 0 to 0.5 mm Insufficient Stripping Length Damage on Side Whisker Correct Incorrect • A pin terminal must be clamped with an appropriate tool based on its size.The tip of a wire must be cut in the same length as the pin terminal or 0.5mm longer. Whiskers are not allowed, and a pin terminal must not be broken. • Plug the pin terminal into the power terminal block to the end.Fix wiring close to its connector so that a cable should not apply load to the connector due to its twisting or weight. • A pin terminal must be unplugged while inserting a flat-head screw driver as shown below. l Main Unit Power Wiring Power supply voltage of the wireless unit is 24VDC.A wireless unit requires 24VDC power supply. Use S8VM/VS series power source of 15W or higher, taking inrush current on startup into account. l Margin and Spacing For heat release, ensure space between a wireless unit and a control panel or other equipment as shown in the right. Power supply voltage 24 VDC Allowable Voltage Range 20.4 to 26.4 VDC Notice on Safety Standards 20mm  or longer 20mm  or longer WE70-AP LANMODE FA WIRELESS LAN ACCESS POINT POWERWIRELESS W E 70- A P F A W I R E L E S S L A N A C C E S S P OI N T L A N M OD E P O WE R W I R ELESS (+) ( - ) Plugging W E 70- A P F A W I R E L E S S L A N A C C E S S P OI N T L A N M OD E P O WE R W I R ELESS Unplugging 24V • This unit needs to be installed under local regulations. • This unit is intended to be supplied by a "Class 2" or  "L.P.S. and rated from 24VDC, 250mA." 120 ±1.0 (Unit: mm) 34.5 ±0.5 36 103 ± 1.0 22.6 107.6 ± 1.0 For WE70-CL Only ETHERNET INIT PUSH RSSI 24V WE70-AP LANMODE FA WIRELESS LAN ACCESS POINT POWERWIRELESS n Dimensions [LAN] Indicator (Orange) Displays a status of the wired LAN. On : LAN connection is normal Off : LAN is not being connected Flashing : Data is being transmitted [MODE] Indicator (Orange)(WE70-AP) Displays an operation mode of the wireless unit. *1 [RSSI] indicator for WE70-CL Displays receiving electric field intensity by flashing. Flashing : Simultaneous flashing of [MODE] and [POWER] indicates setup initialization. Using 802.11a : On Using 802.11b/g : Off WE70-AP WE70-AP LANMODE FA WIRELESS LAN ACCESS POINT POWERWIRELESS LANRSSIPOWERWIRELESS LEVEL4 LEVEL3 LEVEL2 LEVEL1 LEVEL4 LEVEL3 LEVEL2 LEVEL1 Off Off: On On On On: On On When the [RSSI] button on top of the unit is pressed, receiving electric field intensity is displayed on [RSSI], [LAN], and [WIRELESS] indicators in 4 levels.The [POWER] indicator flashes at the same time.Indication returns to its original status when 10 minutes passes or the button is pressed again. ......Stable Level............... ......Usable Level.............. ......Unstable Level........... ......Unusable Level.......... <Flashing> <On> RSSI [RSSI] Indicator (Orange)(WE70-CL) WE70-AP WE70-CL ETHERNET INIT PUSH RSSI ETHERNET INIT <INIT> Button Initializes setup. * Use a pen tip to press. See the WE70-AP/CL FA Wireless LAN Unit OPERA- TIONAL MANUAL (Cat.No.N153-E1), Chapter 6-2. "Restoring to Factory Shipment Status". DC Connector Supplies 24VDC power. RSSI Button Switches receiving status indication. Flashing/4-Level [LAN] Port (RJ-45 x 1) Connects a network device such as a hub through a LAN cable. Antenna Connector Connects accessory antennas. * To ensure performance, always connect both  of 2 antennas. n Components and Functions [POWER] Indicator (Green) Displays a power source status and a wireless unit operation mode. On : The wireless unit is turned on. Flashing : Simultaneous flashing of [POWER] and [MODE]*1 indicates setup initialization. Alternate flashing of [POWER] and [MODE]*1 indicates startup. [WIRELESS] Indicator (Orange) Displays a status of the wireless LAN. On : Radio communication is being established with the wireless unit. Off : Absence of wireless LAN terminal which is communicating with the wireless unit, or no radio communication has been made for 5 or more minutes …

Text truncated - open the document above for the full version.

External Photo Omron Corporation Okayama factory FA Wireless LAN Unit (Model: WE70-AP) FCC ID: RXEWE70AP Top Bottom External Photo Omron Corporation Okayama factory FA Wireless LAN Unit (Model: WE70-AP) FCC ID: RXEWE70AP Front Rear External Photo Omron Corporation Okayama factory FA Wireless LAN Unit (Model: WE70-AP) FCC ID: RXEWE70AP Side 1 Side 2

 ૏⟎ߌ虫ઃ࡞࡯ࠪ࡞ࠕ࡝ࠪ  ޕߔ߹ߒ␜ߦਅ࿑ࠍ૏⟎ߌ虫ઃ࡞࡯ࠪ࡞ࠕ࡝ࠪ   ࿑㧝૏⟎࿑ߌ虫ઃ࡞࡯ࠪ࡞ࠕ࡝ࠪ  Label Location Label Location

Internal Photo Omron Corporation Okayama factory FA Wireless LAN Unit (Model: WE70-AP) FCC ID: RXEWE70AP RF Module Over View RF Module Top (with cover) Internal Photo Omron Corporation Okayama factory FA Wireless LAN Unit (Model: WE70-AP) FCC ID: RXEWE70AP RF Module Bottom RF Module Top (cover off)

Applicant: OMRON Corporation Okayama Factory Type of Equipment : FA Wireless LAN Unit (IEEE802.11a 5725-5850MHz (FCC15.247)) Model No. : WE70-AP FCC ID: RXEWE70AP OMRON Corporation Okayama Factory declares that Model : WE70-AP ⇒ complies with FCC radiation exposure requirement specified in the FCC Rules 2.1093(for portable)/2.1091 (for mobile). RF Exposure Calculations: ← The following information provides the minimum separation distance for the highest gain antenna provided with the “WE70-AP“ as calculate d from FCC OET Bulletin 65 Appendix A, Table (B) Limits for General Population / Uncontrolled Exposure. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0mW/cm^2 uncontrolled exposure limit. The Friis formula used was: S = (P * G) / (4* π * r 2 ) Where P = 119.67 mW (Maximum peak output power) G = 2.19 Numerical Antenna gain; equal 3.40dBi r =20.0 cm For: WE70-APS = 0.05209 mW/cm 2 No. : 27DE0139-HO RF Exposure / MPE Calculation

Applicant: OMRON Corporation Okayama Factory Type of Equipment : FA Wireless LAN Unit (IEEE802.11b/g (FCC15.247)) Model No. : WE70-AP FCC ID: RXEWE70AP OMRON Corporation Okayama Factory declares that Model : WE70-AP ⇒ complies with FCC radiation exposure requirement specified in the FCC Rules 2.1093(for portable)/2.1091 (for mobile). RF Exposure Calculations: ← The following information provides the minimum separation distance for the highest gain antenna provided with the “WE70-AP“ as calculate d from FCC OET Bulletin 65 Appendix A, Table (B) Limits for General Population / Uncontrolled Exposure. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0mW/cm^2 uncontrolled exposure limit. The Friis formula used was: S = (P * G) / (4* π * r 2 ) Where P = 133.97 mW (Maximum peak output power) G = 2.19 Numerical Antenna gain; equal 3.40dBi r =20.0 cm For: WE70-APS = 0.05831 mW/cm 2 No. : 27DE0139-HO RF Exposure / MPE Calculation

Test report No. : 27DE0139-HO-A Page : 2 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) CONTENTS PAGE SECTION 1: Client information ............................................................................................................ 3 SECTION 2: Equipment under test (E.U.T.)........................................................................................ 3 SECTION 3: Test specification, procedures & results......................................................................... 5 SECTION 4: Operation of E.U.T. during testing .................................................................................8 SECTION 5: Conducted Emission....................................................................................................... 11 SECTION 6: Spurious Emission.......................................................................................................... 12 SECTION 7: Bandwidth ....................................................................................................................... 13 SECTION 8: Maximum Peak Output Power ..................................................................................... 13 SECTION 9: Peak Power Density........................................................................................................ 13 APPENDIX 1: Photographs of test setup ............................................................................................ 14 Conducted Emission ............................................................................................................ 14 Spurious Emission (Radiated) ............................................................................................ 16 Worst Case Position (Horizontal: EUT-X-axis, Ant-X-axis/ Vertical:EUT-X-axis, Ant- Y-axis) ................................................................................................................................... 17 APPENDIX 2: Data of EMI test............................................................................................................ 21 Conducted Emission ............................................................................................................ 21 6dB Bandwidth..................................................................................................................... 37 Maximum Peak Output Power........................................................................................... 40 Radiated Spurious Emission (below 1GHz) ...................................................................... 42 Radiated Spurious Emission (above 1GHz) ...................................................................... 54 Conducted Spurious Emission............................................................................................ 74 Conducted emission Band Edge compliance ..................................................................... 84 Power Density....................................................................................................................... 85 99%Occupied Bandwidth ................................................................................................... 88 APPENDIX 3:Test instruments ............................................................................................................ 90 Test report No. : 27DE0139-HO-A Page : 3 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) SECTION 1: Client information Company Name : OMRON Corporation Okayama Factory Address : 2075 Miyoshi Okayama-city, Okayama, 703-8502, Japan Telephone Number : +81-86-276-1797 Facsimile Number : +81-86-276-1520 Contact Person : Shinji Ueno SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : FA Wireless LAN Unit Model No. : WE70-AP Serial No. : 279651000201 (for Radiated Emission and Conducted Emission tests) 279651000202 (for Antenna Terminal Conducted test) Rating : DC 24V (20.4V to 26.4V) Country of Manufacture : JAPAN Receipt Date of Sample : January 19, 2007 Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No modification by the test lab. 2.2 Product Description Model No: WE70-AP is the, FA Wireless LAN Unit (Master). WE70-AP has a variant model: WE70-CL (Slave). It is identical to WE70-AP in radio specification The difference between two models is the presence or absence of RSSI button (for receiving status indication) only. (WE70-AP does not have the button, but WE70-CL does.) Clock Frequencies are 20MHz(CPU Clock), 25MHz(LAN Clock), 80MHz(Memory Clock) and 40MHz (Wireless LAN). Test report No. : 27DE0139-HO-A Page : 4 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) IEEE802.11b / 11g / 11a WLAN Equipment Type Transceiver 11b/11g 2412MHz - 2462MHz Low 5180MHz - 5240MHz *1) Mid 5260MHz - 5320MHz *1) *2) Add 5500MHz - 5700MHz *1) *2) 5745MHz - 5805MHz *1) Frequency of Operation 11a Upper 5825MHz Type of Modulation DSSS, DBPSK, DQPSK, CCK (11b) OFDM, BPSK, QPSK, 16QAM, 64QAM, CCK (11g, 11a) Bandwidth 20MHz Channel spacing 5MHz (11b/11g), 20MHz (11a) Power Supply (inner) DC 3.3V Antenna Connector Type Reverse SMA connector (ANT A and ANT B) Type Model name Gain : Dual Band Diversity Antenna : ANT-S-789 : 2.14dBi (max) Type Model name Gain : Magnetic Pedestal Antenna *3) : WE70-AT001H(OMR04-220100) : 2.4GHz band: 4.5dBi (max) 5GHz band: 7dBi (max) Antenna Information Type Model name Gain : Magnetic Pedestal Antenna with extension ca…

Text truncated - open the document above for the full version.

Test report No. : 27DE0139-HO-A Page : 21 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) APPENDIX 2: Data of EMI test Conducted Emission Dual Band Diversity Ant., 11b, Tx, Ch:Low, High power DATA OF CONDUCTED EMISSION TEST UL Apex Co., Ltd. Head Office EMC Lab. No.2 Semi Anechoic Chamber Date : 2007/02/01 Company : OMRON CorporationReport No.:27DE0139-HO Kind of EUT: FA Wireless LAN Unit Power:AC 120V / 60Hz (DC power supply in) Model No. : WE70-AP Temp./Humi.:25deg.C / 30% Serial No. : 279651000201 Operator:Kenichi Adachi Mode / Remarks : 11b, Tx2412MHz, 11Mbps, Ant:A, with 1/2 Lamda Dual band (2.4G/5G) L Angle LIMIT : FCC15.207 QP FCC15.207 AV CHART:WITH FACTOR,Peak hold data.Data is uncorrected. CALCURATION:RESULT=READING+C.F(LISN LOSS+CABLE Except for the above table : adequate margin data below the Frequency[Hz] [dBuV] << PEAK DATA >> N :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Frequency[Hz] [dBuV] << PEAK DATA >> L :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Test report No. : 27DE0139-HO-A Page : 22 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Conducted Emission Dual Band Diversity Ant., 11b, Tx, Ch:Mid, High power DATA OF CONDUCTED EMISSION TEST UL Apex Co., Ltd. Head Office EMC Lab. No.2 Semi Anechoic Chambe Date : 2007/02/01 Company : OMRON CorporationReport No.:27DE0139-HO Kind of EUT: FA Wireless LAN UnitPower:AC 120V / 60Hz (DC power supply in) Model No. : WE70-AP Temp./Humi.:25deg.C / 30% Serial No.: 279651000201 Operator:Kenichi Adachi Mode / Remarks : 11b, Tx2437MHz, 11Mbps, Ant:A, with 1/2 Lamda Dual band (2.4G/5G) L Angle Antenna LIMIT : FCC15.207 QP FCC15.207 AV CHART:WITH FACTOR,Peak hold data.Data is uncorrected. CALCURATION:RESULT=READING+C.F(LISN LOSS+CABLE LO Except for the above table : adequate margin data below the limits. Frequency[Hz] [dBuV] << PEAK DATA >> N :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Frequency[Hz] [dBuV] << PEAK DATA >> L :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Test report No. : 27DE0139-HO-A Page : 23 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Conducted Emission Dual Band Diversity Ant., 11b, Tx, Ch:Mid, High power DATA OF CONDUCTED EMISSION TEST UL Apex Co., Ltd. Head Office EMC Lab. No.2 Semi Anechoic Chamber Date : 2007/02/01 Company : OMRON CorporationReport No.:27DE0139-HO Kind of EUT: FA Wireless LAN UnitPower:AC 120V / 60Hz (DC power supply in) Model No. : WE70-AP Temp./Humi.:25deg.C / 30% Serial No. : 279651000201 Operator:Kenichi Adachi Mode / Remarks : 11b, Tx2437MHz, 11Mbps, Ant:A, with 1/2 Lamda Dual band (2.4G/5G) L Angle Antenna LIMIT : FCC15.207 QP FCC15.207 AV CHART:WITH FACTOR,Peak hold data.Data is uncorrected. CALCURATION:RESULT=READING+C.F(LISN LOSS+CABLE LOSS Except for the above table : adequate margin data below the limits. Frequency[Hz] [dBuV] << QP/AV DATA >> L :QP :AV N :QP :AV .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Frequency Reading Level Reading Level Corr . ResultsResultsLimitLimitMarginMargin PhaseComment Frequency QP AV Factor QPAVQPAVQPAVPhaseComment [ MHz ] [dBuV ] [ dBuV ] [ dB ] [dBuV][dBuV][dBuV][dBuV][dB][dB] PhaseComment 0 . 1500026 . 5 20 . 4 0 . 2 26.720.666.056.039.335.4N 0 . 1500026 . 5 20 . 5 0 . 2 26.720.766.056.039.335.3L 0 . 2821723 . 5 1 . 7 0 . 4 23.92.160.850.836.948.7N 0 . 2779724 . 6 2 . 2 0 . 4 25.02.660.950.935.948.3L 3 . 1991124 . 7 24 . 5 0 . 7 25.425.256.046.030.620.8N 3 . 1991124 . 8 24 . 6 0 . 7 25.525.356.046.030.520.7L 4 . 9955339 . 7 29 . 5 1 . 0 40.730.556.046.015.315.5N* 4 . 9955339 . 6 29 . 5 1 . 0 40.630.556.046.015.415.5L 5 . 4869641 . 2 29 . 4 1 . 0 42.230.460.050.017.819.6N 5 . 4870741 . 3 29 . 6 1 . 0 42.330.660.050.017.719.4L 12 . 0317334 . 6 28 . 4 1 . 5 36.129.960.050.023.920.1N 12 . 1739334 . 6 28 . 5 1 . 5 36.130.060.050.023.920.0L 26 . 5984920 . 0 15 . 9 2 . 4 22.418.360.050.037.631.7N 26 . 5984920 . 0 15 . 5 2 . 4 22.417.960.050.037.632.1L *The limit is rounded down to one decimal place. *The test result is round off to one or two decimal places, so some differences might be observed. Test report No. : 27DE0139-HO-A Page : 24 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Conducted Emission Dual Band Diversity Ant., 11b, Tx, Ch:High, High power DATA OF CONDUCTED EMISSION TEST UL Apex Co., Ltd. Head Office EMC Lab. No.2 Semi Anechoic Chamber Date : 2007/02/01 Company : OMRON Corporation Report No.:27DE0139-HO Kind of EUT : FA Wireless LAN UnitPower:AC 120V / 60Hz (DC power supply in) Model No. : WE70-AP Temp./Humi.:25deg.C / 30% Serial No. : 279651000201 Operator:Kenichi Adachi Mode / Remarks: 11b, Tx2462MHz, 11Mbps, Ant:A, with 1/2 Lamda Dual-band (2.4G/5G) L Angle Antenna LIMIT : FCC15.207 QP FCC15.207 AV CHART:WITH FACTOR,Peak hold data.Data is uncorrected. CALCURATION:RESULT=READING+C.F(LISN LOSS+CABLE Except for the above table : adequate margin data below the limits. Frequency[Hz] [dBuV] << PEAK DATA >> N :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Frequency[Hz] [dBuV] << PEAK DATA >> L :PEAK .15M 30M .2M .3M .5M .7M 1M2M3M5M7M10M20M 0 10 20 30 40 50 60 70 80 90 Test report No. : 27DE0139-HO-A Page : 25 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office…

Text truncated - open the document above for the full version.

Test report No. : 27DE0139-HO-A Page : 14 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) APPENDIX 1: Photographs of test setup Conducted Emission (with Dual Band Diversity Antenna) Front Rear Test report No. : 27DE0139-HO-A Page : 15 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Conducted Emission (with Magnetic Pedestal Antenna) Front Rear Test report No. : 27DE0139-HO-A Page : 16 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Spurious Emission (Radiated) (with Dual Band Diversity Antenna) Front Rear Test report No. : 27DE0139-HO-A Page : 17 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Worst Case Position (Horizontal: EUT-X-axis, Ant-X-axis/ Vertical:EUT-X-axis, Ant-Y-axis) (with Dual Band Diversity Antenna) EUT - X-axis Ant - X-axis EUT - Y-axis Ant - Y-axis EUT - Z-axis Ant - Z-axis Test report No. : 27DE0139-HO-A Page : 18 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Spurious Emission (Radiated) (with Magnetic Pedestal Antenna) Front Rear Test report No. : 27DE0139-HO-A Page : 19 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Spurious Emission (Radiated) (with Magnetic Pedestal Antenna + extension cable 5m) Front Rear Test report No. : 27DE0139-HO-A Page : 20 of 91 Issued date : March 26, 2007 FCC ID : RXEWE70AP UL Apex Co., Ltd. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 MF060b(14.06.06) Worst Case Position (Horizontal: EUT-X-axis, Ant-X-axis/ Vertical:EUT-X-axis, Ant-Y-axis) (with Magnetic Pedestal Antenna) EUT - X-axis Ant - X-axis EUT - Y-axis Ant - Y-axis EUT - Z-axis Ant - Z-axis