RYQ-NFFDATA CARD

Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement." CAN ICES-3(B)/ NMB-3(B) Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. End Product Labeling When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: RYQ-NFF” "Contains IC: 6719C-NFF" The grantee's FCC ID/IC ID can be used only when all FCC/IC compliance requirements are met. This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co-located with any other transmitter or antenna. (3) To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure condition must not exceed: 。 6.5 dBi in Cellular band 。 2.0 dBi in PCS band 。 5.5 dBi in AWS band In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization.

M.2 connector, embeded into Ultrabook or Pad device Connect to 2G/3G antenna Connect to 3G diversityand GPS antenna Quick Install Guide Module : NFF 6260 (2G/3G) data card 1. The Data Card connector (Pins) insert into NGFF connector (femal)2. Plug 3G diversity/GPS antenna cable to system connector.3. Plug 2G/3G antenna cable to system connector.4. Fixing Data card in System.

Foxconn International Holdings Ltd. No.4, Mingsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan, R.O.C. Date: June 19, 2013 Modular Approval Check list FCC ID: RYQ-NFF Item Requirements EUT 1. The modular transmitter must have its own RF shielding. The module is equipped with its own shielding case. 2. The modular transmitter must have buffered modulation / data inputs. The module has buffer modulation / data inputs. 3. The modular transmitter must have its own power supply regulation. The module has its own power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), Not applicable to licensed modules 5. The modular transmitter must be tested in a stand-alone configuration. EUT conformance testing was performed in a standalone configuration. 6. The modular transmitter must be labeled with its own FCC ID number. The module transmitter will be labeled with its own FCC ID, and for OEM integration the integration manual contains labeling instructions for the host device per Part 15.212 (vi) 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The module approved transmitter complies with all applicable rules and the integration manual contains any specific requirements addressed to the integrator and/or to the end-user of the final end-product. 8. The modular transmitter must comply with any applicable RF exposure requirement. Compliance with RF exposure requirement is addressed in RF exposure report.

Photographs of EUT Report No.: EP312451 Brand Name: Ambit / Model Name: NFF / Marketing Name: Ambit NFF SPORTON INTERNATIONAL INC. Page Number : 1 of 8 TEL : 886-3-327-3456 Report Issued Date : Jun. 13, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID: RYQ-NFF IC : 6719C-NFF 1. External Photograph of EUT Photographs of EUT Report No.: EP312451 Brand Name: Ambit / Model Name: NFF / Marketing Name: Ambit NFF SPORTON INTERNATIONAL INC. Page Number : 2 of 8 TEL : 886-3-327-3456 Report Issued Date : Jun. 13, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID: RYQ-NFF IC : 6719C-NFF 720510

Front of the module Shield Label Location

NgFF 6260 –Label Brand: AMBIT Model Name: NFF

Photographs of EUT Report No.: EP312451 Brand Name: Ambit / Model Name: NFF / Marketing Name: Ambit NFF SPORTON INTERNATIONAL INC. Page Number : 3 of 4 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID: RYQ-NFF IC : 6719C-NFF 2. Internal Photograph of EUT Photographs of EUT Report No.: EP312451 Brand Name: Ambit / Model Name: NFF / Marketing Name: Ambit NFF SPORTON INTERNATIONAL INC. Page Number : 4 of 4 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID: RYQ-NFF IC : 6719C-NFF 720510

SPORTON INTERNATIONAL INC. Page Number : 1 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 RF Exposure Evaluation Report APPLICANT : Foxconn International Holdings Ltd. EQUIPMENT : Data Card BRAND NAME : Ambit MODEL NAME : NFF MARKETING NAME Ambit NFF FCC ID : RYQ-NFF STANDARD : 47 CFR Part 2.1091 We, SPORTON INTERNATIONAL INC., would like to declare that the device has been evaluated in accordance with 47 CFR Part 2.1091, and pass the limit. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. Approved by: Jones Tsai / Manager Reviewed by: Eric Huang / Deputy Manager SPORTON INTERNATIONAL INC. Page Number : 2 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 Table of Contents 1. ADMINISTRATION DATA ........................................................................................................................... 4 1.1. Testing Laboratory ............................................................................................................................. 4 1.2. Applicant ............................................................................................................................................ 4 1.3. Manufacturer ...................................................................................................................................... 4 2. DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ............................................................................. 5 3. RF EXPOSURE LIMIT INTRODUCTION .................................................................................................... 6 4. MAXIMUM RF AVERAGE OUTPUT POWER AMONG PRODUCTION UNITS ........................................ 7 5. CONDUCTED RF OUTPUT POWER (UNIT: DBM) .................................................................................... 8 6. RADIO FREQUENCY RADIATION EXPOSURE EVALUATION ............................................................. 10 SPORTON INTERNATIONAL INC. Page Number : 3 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 Revision History REPORT NO. VERSION DESCRIPTION ISSUED DATE FA312451 Rev. 01 Initial issue of report Jun. 19, 2013 SPORTON INTERNATIONAL INC. Page Number : 4 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 1. Administration Data 1.1. Testing Laboratory Test Site SPORTON INTERNATIONAL INC. Test Site Location No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL: +886-3-327-3456 FAX: +886-3-328-4978 1.2. Applicant Company Name Foxconn International Holdings Ltd. Address No. 4, Mingsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan (R. O. C.) 1.3. Manufacturer Company Name Foxconn International Holdings Ltd. Address No. 4, Mingsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan (R. O. C.) SPORTON INTERNATIONAL INC. Page Number : 5 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 2. Description of Equipment Under Test (EUT) Product Feature & Specification EUT Type Data Card Brand Name Ambit Model Name NFF Marketing name Ambit NFF FCC ID RYQ-NFF IMEI Code 354221050007586 Tx Frequency GSM850: 824.2 MHz ~ 848.8 MHz GSM1900: 1850.2 MHz ~ 1909.8MHz WCDMA Band V: 826.4 MHz ~ 846.6 MHz WCDMA Band II: 1852.4 MHz ~ 1907.6 MHz WCDMA Band IV: 1712.4 MHz ~ 1752.6 MHz HW Version PR3 SW Version V13.05 Uplink Modulation GPRS: GMSK EDGE: GMSK / 8PSK WCDMA /HSPA: QPSK EUT Stage Production Unit Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. SPORTON INTERNATIONAL INC. Page Number : 6 of 11 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF RF Exposure Evaluation Report Report No. : FA312451 3. RF Exposure Limit Introduction The FCC categorizes the RF exposure limit based on the intended usage of the device and the user’s awareness and ability to exercise control over his or her exposure. This is a consumer product to be used in the home, hence this device was evaluated by mobile device with general population/uncontrolled exposure condition. The definition of these category are shown as follows:  Mobile Devices: A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters' radiating structures and the body of the user or nearby persons. Transmitters designed to be used by consumers or workers that can be easily re-located are considered mobile devices if they meet the 20 centimeter separation requirement. The FCC rules for evaluating mobile devices for RF compliance are found in 47 CFR Part 2.1091.  General Population/Uncontrolled Exposure: The general population / uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Members of the general public would come under this category when exposure is not employment-related…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. Page Number : 1 of 112 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF FCC RF Test Report Report No. : FG312451 FCC RF Test Report APPLICANT : Foxconn International Holdings Ltd. EQUIPMENT : Data Card BRAND NAME : Ambit MODEL NAME : NFF MARKETING NAME : Ambit NFF FCC ID : RYQ-NFF STANDARD : FCC 47 CFR Part 2, 22(H), 24(E), 27(L) CLASSIFICATION : PCS Licensed Transmitter (PCB) The product was received on Jan. 24, 2013 and completely tested on Mar. 04, 2013. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI / TIA / EIA-603-C-2004 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor Approved by: Jones Tsai / Manager SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. SPORTON INTERNATIONAL INC. Page Number : 2 of 112 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF FCC RF Test Report Report No. : FG312451 TABLE OF CONTENTS REVISION HISTORY .......................................................................................................................................... 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .......................................................................................................................... 5 1.1 Applicant ............................................................................................................................................ 5 1.2 Manufacturer ..................................................................................................................................... 5 1.3 Feature of Equipment Under Test ..................................................................................................... 5 1.4 Product Specification of Equipment Under Test ............................................................................... 6 1.5 Modification of EUT ........................................................................................................................... 6 1.6 Frequency Tolerance and Emission Designator ............................................................................... 6 1.7 Testing Site........................................................................................................................................ 7 1.8 Applied Standards ............................................................................................................................. 7 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 8 2.1 Test Mode.......................................................................................................................................... 8 2.2 Connection Diagram of Test System .............................................................................................. 10 2.3 Support Unit used in test configuration and system ........................................................................ 10 2.4 Measurement Results Explanation Example .................................................................................. 11 3 TEST RESULT ........................................................................................................................................... 12 3.1 Conducted Output Power Measurement ......................................................................................... 12 3.2 Peak-to-Average Ratio .................................................................................................................... 14 3.3 Occupied Bandwidth and 26dB Bandwidth Measurement .............................................................. 30 3.4 Band Edge Measurement ................................................................................................................ 54 3.5 Conducted Spurious Emission Measurement ................................................................................. 69 3.6 Field Strength of Spurious Radiation Measurement ....................................................................... 88 3.7 Frequency Stability Measurement ................................................................................................. 105 4 LIST OF MEASURING EQUIPMENTS.................................................................................................... 111 5 UNCERTAINTY OF EVALUATION ......................................................................................................... 112 APPENDIX A. PHOTOGRAPHS OF EUT APPENDIX B. SETUP PHOTOGRAPHS SPORTON INTERNATIONAL INC. Page Number : 3 of 112 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF FCC RF Test Report Report No. : FG312451 REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FG312451 Rev. 01 Initial issue of report Jun. 19, 2013 SPORTON INTERNATIONAL INC. Page Number : 4 of 112 TEL : 886-3-327-3456 Report Issued Date : Jun. 19, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF FCC RF Test Report Report No. : FG312451 SUMMARY OF TEST RESULT Report Section FCC Rule IC Rule Description Limit Result Remark 3.1 §2.1046 RSS-132 (5.4) RSS-133 (6.4) RSS-139 (6.4) Conducted Output Power Reporting Only PASS - 3.2 §24.232(d) §27.50(d)(5) RSS-132 (5.4) RSS-133(6.4) RSS-139 (6.4) Peak-to-Average Ratio < 13 dB PASS - 3.3 §2.1049 §22.917(a) §24.238(b) §27.53(g) RSS-GEN(4…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. Page Number : B1 of B1 TEL : 886-3-327-3456 Report Issued Date : Jun. 13, 2013 FAX : 886-3-328-4978 Report Version : Rev. 01 FCC ID : RYQ-NFF FCC RF Test Report Report No. : FG312451 Appendix B. Setup Photographs <Radiated Emission> LF HF