RYQSTTM21VAPP4G cellular phone

ROUVO V Have questions about your Prepaid phone? You’re in the right place. Find out how to set up and use your phone, access special features, get help and lots more. We’re here to help. About your phone NOTE: Devices and software are constantly evolving. The screen images and icons you see here are for reference only. USB-C/ Charger port Power/Lock key Front camera Headset port SIM & microSD card slot Rear camera Volume Up/Down About your phone Fingerprint sensor Flash Microphone Speaker Proximity / Light sensor Your phone already has a SIM card installed. For an optimal wireless experience, use the SIM installed in your new phone. However, if you purchase this phone without SIM card pre-installed, or if you wish to replace your SIM card for any reason, follow the steps below. The following steps also guide you to install your microSD card. 1. Use the SIM ejector tool. Use the supplied SIM ejector tool to insert into the small hole on the SIM/ SD Card tray. 2. Pull the tray out to place SIM/microSD card. Pull the tray out and place your Nano SIM card and microSD card on the tray. Make sure you align the cards as designated by the tray. 3. Push the tray back into its place. Slide the tray attached with your Nano SIM card and microSD card all the way into the slot. NOTE: The microSD card is sold separately. Setting up your phone Setting up your phone SIM card tray microSD Nano SIM 4. Charge your phone. Before turning on your phone, charge it fully. 1. Plug in the USB-C connector (the smaller end) of the USB charging cable into the USB-C/Charger port of your phone. 2. Plug in another end of thecable (the larger end) into the USB connector of the supplied AC adapter. 3. Plug the AC adapter into an available power outlet. WARNING: Only use approved chargers with your device. Incompatible chargers or tampering with the charger port could damage your device and void the warranty. 5. Turn your phone on/off. To turn your phone on, press and hold the Power/Lock button until the phone vibrates. NOTE: The first time you turn on your phone, you will need to activate it. See the Welcome Guide included with your phone. To turn your phone off, press and hold the Power/Lock key and then tap Power off. Locking/unlocking the screen To turn on your screen, press the Power/Lock key. Then swipe up on the screen to unlock it. To turn off your screen and prevent accidental key presses, press the Power/Lock key. Setting up your phone Power/Lock key Using your phone Starting your phone for the first time 1. Once you have turned on and initialized your phone, tap to select your preferred language for your phone, then tap . 2. From the Phone Activation screen, tap Next (assuming you have activated your SIM card as instructed in the Welcome Guide). 3. You will be prompted to connect to a wireless network. If you have a SIM card, you can use mobile network for setup, or connect to an available Wi-Fi network. Enter password if required. 4. To Copy apps & data from another device, tap Next, or tap Don’t copy to continue. If you tap Next, follow the on-screen steps. 5. To Sign in with your Google™ account, enter your account information and tap Next, or tap Skip to skip to the next step. If you sign in your Google™ account, tap I agree to the Google Terms and Services shown on the screen. 6. From the Google services screen, tap More and then Accept if you agree to the default selection of these Google services settings. You may turn on/off the services later with the toggle switch. 7. Set PIN for screen lock, or tap Skip to continue. 8. Set your Verizon Services. Tap ACCEPT to use the default settings for the services. 9. Set your Verizon Cloud, tap NEXT to enter Verizon Cloud Setup. Select what to backup and then tap NEXT. 10. Choose Wi-Fi only or Both Wi-Fi and Mobile Networks to back up your content on Verizon Cloud. You may change it anytime in Settings. 11. When you see Ready to go, tap GOT IT to complete the initial setup. Touch screen tips Use touch gestures to move around the screen, open menus, select items, zoom in and out of web pages, apps and more. There are several touch gestures recognized by your phone: • Ta p—Gently touch the touch screen with your fingertip to select items. • Tap & Hold—Tap and hold on an item or a space to open menus. • Swipe—Gently slide your finger on the touch screen like a mouse scroll. • Drag—Hold onto an item and drag it to a new position. • Pinch & Spread—Pinch and spread with your thumb and index finger to zoom in or out. Accessing Apps from Home Screen You can access all your apps, whether pre-installed by default, transferred from your last phone or downloaded, from the Home Screen. Simply swipe up from the Home Screen and you will be able to view and access all your apps. Using your phone Setting up voice mail 1. Dial *86 and press Send. 2. When you hear a greeting, press # to interrupt. 3. Follow the setup instructions. Checking voice mail From your phone: 1. Dial *86 and press Send. 2. Follow the instructions. From other phones: 1. Dial your mobile number. 2. When you hear the greeting, press # to interrupt. 3. Follow the instructions. NOTE: Voice mailboxes not set up within 45 days will be canceled. Your voice mailbox is not password protected until you create a password by following the setup tutorial. Voice mail may not be available in some areas. Follow the setup instructions to password protect your Verizon voice mailbox. Verizon is not responsible for missed messages or deletions of messages from your voice mailbox, even if you have saved them. Using your phone Making a call 1. From the Home Screen, tap the Phone icon. 2. Tap the Dialpad icon. 3. Enter the number you want to call. 4. Tap the Call icon to place the call. You may also • Tap a saved contact in Contacts • Tap a recent call log in Recents • Tap a favorite contact in Favorites • Tap voice search function to find the contact Answering or Declining a call During an incoming call, • Tap ANSWER on the call …

Text truncated - open the document above for the full version.

FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Date: 2022-03-17 DFS client device channel plan and software operational declaration We, FIH CO., LTD., declare that the device, FCC ID: RYQSTTM21VAPP, Model Name: STTM21VAPP, does not have Ad Hoc on “non-US frequencies” and/or on“ DFS frequencies“. Also, the client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes. Below is the channel / frequency plan for the device Also, on DFS channels, the WLAN driver in the device operates under the control of an AP at all times, except when in ad-hoc mode on US non-DFS channels. The device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is protected by a special signature and CRC checksum. Signature and CRC checksum will be calculated and verified before firmware upgrade. Unauthorized modification to firmware will lead to the failure of verification and thus firmware upgrade will not be allowed. If you have any questions regarding the declaration, please don’t hesitate to contact us. CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 Scan Type Active Active Active Active Active Active Active Active Active Active Active CH 36 38 40 42 44 46 48 Frequency (MHz) 5180 5190 5200 5210 5220 5230 5240 Scan Type Active Active Active Active Active Active Active CH 52 54 56 58 60 62 64 Frequency (MHz) 5260 5270 5280 5290 5300 5310 5320 Scan Type Passive Passive Passive Passive Passive Passive Passive CH 100 102 104 106 108 110 112 116 Frequency (MHz) 5500 5510 5520 5530 5540 5550 5560 5580 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive CH 132 134 136 140 Frequency (MHz) 5660 5670 5680 5700 Scan Type Passive Passive Passive Passive CH 149 151 153 155 157 159 161 165 Frequency (MHz) 5745 5755 5765 5775 5785 5795 5805 5825 Scan Type Active Active Active Active Active Active Active Active FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Sincerely yours, ________________________________________ Barry Tsai / Manager FIH CO., LTD. Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 E-mail: [email protected]

FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Date: 2022-03-17 FCC ID: RYQSTTM21VAPP FCC E-Label Information Model: STTM21VAPP A. Information to be displayed The information that will be displayed on the e-label and information that will remain in the user manual is shown below: Information on E-label In Manual FCC ID number Yes Yes Compliance statement No Yes Caution to the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment 1 No Yes Describe any other FCC regulatory information included in e-label 1 1 If the e-label includes information typically included in the manual then the e-label shall clearly differentiate between information required to be on the device’s surface and information required to be in the manual – refer to 784748 D02 e labelling v01 section II D 3(b) Images of the e-label screen are provided below: Model STTM21VAPP: FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 B. Access to the required information on the e-label 1. Users are able to access the information in no more than three steps in a device’s menu. The actual steps are: To access the e-label information, in the device, Choose: Settings > About Phone >Regulatory labels No special access codes or permissions are required to go through the above steps beyond entering a user- defined password to protect against unauthorized access to the device. 2. The information is stored on the device, no special accessories or SIM/USIM card are required to access the information. Yes C. LABELING FOR IMPORTATION AND PURCHASING Products utilizing e-labels are required to have a physical label on the product at the time of importation, marketing and sales. For devices imported in bulk and not packaged individually, a removable adhesive label or, for devices in protective bags, a label on the bags is acceptable for this purpose. Any removable label shall be of a type intended to survive normal shipping and handling and must only be removed by the customer after purchase. The device will have required physical label on the packaging, which include the device’s FCC ID. D. OTHER CONSIDERATIONS 1. Electronic labeling information must be programmed by the responsible party and the information must be secured in such a manner that third-parties cannot modify it. The e-label information is pre-programmed by the grantee. The user cannot modify the e-label information. 2. All the applicable regulatory information required on the packaging or user instructions must be provided according to the rules even if it is displayed electronically. For example, hearing aid compatibility (HAC) ratings for the phones as specified in 47 C.F.R. § 20.19. Yes, it is provided. Sincerely yours, ________________________________________ Barry Tsai / Manager FIH CO., LTD. Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 E-mail: [email protected]

FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Date: 2022-03-11 FCC ID: RYQSTTM21VAPP To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Software Operational Description Tune Up Procedure Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ________________________________________ Barry Tsai / Manager FIH CO., LTD. Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 E-mail: [email protected]

FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Date: 2022-03-11 FCC ID: RYQSTTM21VAPP To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 120 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Internal Photos Test Setup photos User’s manual Sincerely yours, ________________________________________ Barry Tsai / Manager FIH CO., LTD. Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 E-mail: [email protected]

FIH CO., LTD. No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 Date: 2022-03-11 FCC ID: RYQSTTM21VAPP AUTHORIZATION LETTER To Whom It May Concern: FIH CO., LTD. hereby authorizes Amanda Wu and Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu and Senior Specialist of BV CPS Taoyuan on FIH CO., LTD. ‘s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ________________________________________ Barry Tsai / Manager FIH CO., LTD. Tel: 886-2-2268-5511 / FAX: 886-2-2269-2922 E-mail: [email protected]

Reference No.: BFOK-WTW-P22010278_EXT Page 1/7 CONSTRUCTION PHOTOS OF EUT Reference No.: BFOK-WTW-P22010278_EXT Page 2/7 Reference No.: BFOK-WTW-P22010278_EXT Page 3/7 Reference No.: BFOK-WTW-P22010278_EXT Page 4/7 Reference No.: BFOK-WTW-P22010278_EXT Page 5/7 Reference No.: BFOK-WTW-P22010278_EXT Page 6/7 Reference No.: BFOK-WTW-P22010278_EXT Page 7/7

FCC ID: RYQSTTM21VAPP Back side of EUT The label will be permanently affixed and readily visible. Label location

QR label: show MFD (Manufacture date) number and IMEI number. After scan QR label, Show as: 220228,350025200000000

Reference No.: BFOK-WTW-P22010278_INT Page 1/15 CONSTRUCTION PHOTOS OF EUT Reference No.: BFOK-WTW-P22010278_INT Page 2/15 Reference No.: BFOK-WTW-P22010278_INT Page 3/15 Reference No.: BFOK-WTW-P22010278_INT Page 4/15 Reference No.: BFOK-WTW-P22010278_INT Page 5/15 Reference No.: BFOK-WTW-P22010278_INT Page 6/15 Reference No.: BFOK-WTW-P22010278_INT Page 7/15 Reference No.: BFOK-WTW-P22010278_INT Page 8/15 Reference No.: BFOK-WTW-P22010278_INT Page 9/15 Reference No.: BFOK-WTW-P22010278_INT Page 10/15 Reference No.: BFOK-WTW-P22010278_INT Page 11/15 Reference No.: BFOK-WTW-P22010278_INT Page 12/15 Reference No.: BFOK-WTW-P22010278_INT Page 13/15 Reference No.: BFOK-WTW-P22010278_INT Page 14/15 Reference No.: BFOK-WTW-P22010278_INT Page 15/15

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 32 Report No. : SFBFOK-WTW-P22010278 Issued Date : Mar. 17, 2022 SAR Test Report Report No. : SFBFOK-WTW-P22010278 Applicant : FIH CO., LTD. Address : No.4, Minsheng St., Tu-Cheng Dist., New Taipei City 23679, Taiwan Product : 4G cellular phone FCC ID : RYQSTTM21VAPP Brand : SHARP Model No. : STTM21VAPP Standards : FCC 47 CFR Part 2 (2.1093), IEEE C95.1:1992, IEEE Std 1528:2013 KDB 865664 D01 v01r04, KDB 865664 D02 v01r02, KDB 248227 D01 v02r02, KDB 447498 D01 v06, KDB 648474 D04 v01r03, KDB 941225 D01 v03r01, KDB 941225 D05 v02r05, KDB 941225 D06 v02r01 Sample Received Date : Jan. 22, 2022 Date of Testing : Jan. 26, 2022 ~ Jan. 28, 2022 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Vera Huang / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 32 Report No. : SFBFOK-WTW-P22010278 Issued Date : Mar. 17, 2022 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot ............................................................................................................................................................... 7 3.2.2 Probes ............................................................................................................................................................. 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................. 8 3.2.4 Phantoms ......................................................................................................................................................... 8 3.2.5 Device Holder .................................................................................................................................................. 9 3.2.6 System Validation Dipoles ............................................................................................................................. 10 3.2.7 Power Source ................................................................................................................................................ 10 3.2.8 Tissue Simulating Liquids .............................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 13 3.4 SAR Measurement Procedure ................................................................................................................................... 14 3.4.1 Area Scan and Zoom Scan Procedure .......................................................................................................... 14 3.4.2 Volume Scan Procedure ...............................................................…

Text truncated - open the document above for the full version.

Plots of System Verification Annex A. Plots of System Verification The plots for system verification are shown as follows. Report No. : SFBFOK-WTW-P22010278 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/01/27 S01 System Check_H1900_220127 DUT: Dipole 1900 MHz; Type: D1900V2; SN: 5d036 Communication System: UID 0, CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium: H16T20N1_0127 Medium parameters used: f = 1900 MHz; σ = 1.463 S/m; ε r = 38.834; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C ; Liquid Temperature：23.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(8.27, 8.27, 8.27) @ 1900 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 3.04 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 45.12 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 3.62 W/kg SAR(1 g) = 1.91 W/kg; SAR(10 g) = 1.02 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 3.05 W/kg Report No. : SFBFOK-WTW-P22010278 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/01/27 S02 System Check_H835_220127 DUT: Dipole 835 MHz; Type: D835V2; SN: 4d121 Communication System: UID 0, CW; Frequency: 835 MHz;Duty Cycle: 1:1 Medium: H07T10N1_0127 Medium parameters used: f = 835 MHz; σ = 0.934 S/m; ε r = 40.295; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C ; Liquid Temperature：23.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(10.5, 10.5, 10.5) @ 835 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.641 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 26.84 V/m; Power Drift = -0.07 dB Peak SAR (extrapolated) = 0.699 W/kg SAR(1 g) = 0.450 W/kg; SAR(10 g) = 0.298 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 0.620 W/kg Report No. : SFBFOK-WTW-P22010278 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/01/26 S03 System Check_H750_220126 DUT: Dipole 750 MHz; Type: D750V3; SN: 1013 Communication System: UID 0, CW; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: H06T09N1_0126 Medium parameters used: f = 750 MHz; σ = 0.902 S/m; ε r = 41.563; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(10.69, 10.69, 10.69) @ 750 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.526 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 25.46 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 0.591 W/kg SAR(1 g) = 0.394 W/kg; SAR(10 g) = 0.260 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 0.529 W/kg Report No. : SFBFOK-WTW-P22010278 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/01/26 S04 System Check_H750_220126 DUT: Dipole 750 MHz; Type: D750V3; SN: 1013 Communication System: UID 0, CW; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: H06T09N1_0126 Medium parameters used: f = 750 MHz; σ = 0.902 S/m; ε r = 41.563; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.3 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(10.69, 10.69, 10.69) @ 750 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.526 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 25.46 V/m; Power Drift = 0.01 dB Peak SAR (extrapolated) = 0.591 W/kg SAR(1 g) = 0.394 W/kg; SAR(10 g) = 0.260 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 0.529 W/kg Report No. : SFBFOK-WTW-P22010278 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/01/27 S05 System Check_H1750_220127 DUT: Dipole 1750 MHz; Type: D1750V2; SN: 1055 Communication System: UID 0, CW; Frequency: 1750 MHz;Duty Cycle: 1:1 Medium: H16T20N1_0127 Medium parameters used: f = 1750 MHz; σ = 1.372 S/m; ε r = 39.099; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C ; Liquid Temperature：23.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(8.55, 8.55, 8.55) @ 1750 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.80 W/kg Pin=50mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 46.57 V/m; Power Drift = -0.06 dB Peak SAR (extrapolated) = 3.35 W/kg SAR(1 g) = 1.79 W/kg; SAR(10 g) = 0.…

Text truncated - open the document above for the full version.

Annex Z. Calibration Certificate for Probe and Dipole The SPEAG calibration certificates are shown as follows. Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Annual Confirmation of SAR Reference Dipole Model：D1900V2S/N： 5d036Measurement Date： 2022/1/21 Frequency (MHz) TypeItem Previous Measurement Annual Check Deviation Accepted Tolerance Result Real Im pedance 50.40453.1102.71±5ΩPASS Imaginary Im pedance 0.53363.32002.79±5ΩPASS Return Loss -25.456-28.02610.10%±20%PASS 1900 MHz，Free Space 1900 Free Space Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : SFBFOK-WTW-P22010278 Report No. : S…

Text truncated - open the document above for the full version.