S6J-34173417 UHF RAIN RFID Reader Module

● ● ● ● PIN NAME 1 – 4 VCC (5 – 15V DC) 5 ENABLE 6 I/O 1 (I2C Master SCL) 7 I/O 2 (I2C Master SDA) 8 UART TX 9 UART RX 10 USB DM 11 USB DP 12 I/O 4 13 I/O 3 14 DNU (Connect to GND or leave floating) 15 – 18 GND Ω • o • • • • ● ● ● ● o o

Suite A, Loughborough Technology Centre, Epinal Way, Loughborough, Leicestershire, LE11 3GE, United Kingdom Call: +44 (0)1509 238248 • Fax: +44 (0)1509 214144 • Email: [email protected] • Website: www.tsl.com Date: June 22, 2023 Certification Attestation Statements Attn: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA FCC ID: S6J-3417 To Whom It May Concern: 47 CFR section 2.911(d)(5)(i) Attestation Statement Technology Solutions (UK) Ltd certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 47 CFR section 2.911(d)(5)(ii) Attestation Statement Technology Solutions (UK) Ltd (“the applicant”) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Thank you, Signature Name David Evans Title Founder Company Technology Solutions (UK) Ltd Tel # +441509238248 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist .

Certification designating a U.S. Agent for service of process: As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must: i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council: The Agent for Process of Service: • cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB) • cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab) • Agent can be Individual Entity or a Company Entity • Agent Entity must be located in US, US address/phone • Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter) • Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. U.S. Agent Designation for Service of Process A TTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th Ave South, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Email: [email protected] FRN #: 0027533835 T his letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U .S. Agent Signature: Da te: Si gned by (Printed Name/Title): Nathan Grinager / Co-President *This letter is valid indefinitely for all applications submitted within the period of 5/ 31/2023 –5/31/2024 T he Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Technology Solutions (UK) Ltd Service Type: original application, class 2 permissive change, class 3 permissive change, etc. FCC ID: S6J-3417 Module type: single-modular transmitter Contact Name: David Evans Street Address: Suite A, Loughborough Technology Centre, Epinal Way, Leicestershire. City/Province/Zip: Loughborough, United Kingdom, LE11 3GE Telephone No: +441509238248 Email: [email protected] June 5, 2023 Applicant Signature: Date: Signed by (Printed Name/Title): David Evans *By signing this letter, the client declares and agrees that the service provided by Approve-IT, Inc. will only be applicable for the module model described above. The client also declares and accepts that the service won’t be applicable in any way to any host devices that could contain the module for which the service has been contracted.

Suite A, Loughborough Technology Centre, Epinal Way, Loughborough, Leicestershire, LE11 3GE, United Kingdom Call: +44 (0)1509 238248 • Fax: +44 (0)1509 214144 • Email: [email protected] • Website: www.tsl.com Company No. 02777518 VAT No. GB 620030611 Date: 2023-01-04 FCC ID: S6J-3417 AUTHORISATION LETTER Technology Solutions (UK) Ltd hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on Technology Solutions (UK) Ltd’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorisation, please don’t hesitate to contact us. Sincerely, ----------------------------------- Dr David Evans / Founder Technology Solutions (UK) Ltd Email: [email protected]

FCC ID: S6J-3417 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch August 25, 2023 Dear Application Examiner, Technology Solutions (UK) Ltd, FCC ID: S6J-3417 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip E710. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is chip E710. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via test tool. Please see section Photographs of Test Configuration in the test report, the EUT was linked to test tools. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: S6J-3417 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Andrea Hsia / Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Reference No.: BHTN-WTW-P22110245_EXT Page 1/5 CONSTRUCTION PHOTOS OF EUT Reference No.: BHTN-WTW-P22110245_EXT Page 2/5 Reference No.: BHTN-WTW-P22110245_EXT Page 3/5 Reference No.: BHTN-WTW-P22110245_EXT Page 4/5 Reference No.: BHTN-WTW-P22110245_EXT Page 5/5

www.tsl.com Design • Development • Manufacture 3417 RAIN RFID MODULE LABEL INFORMATION 3417 Label Location v1.01Copyright © 2023 Technology Solutions (UK) Ltd 2 3417 RAIN RFID Module Label Information Label Content The ID Label contains the module’s serial number, part number, the date of manufacture, the country of manufacture and the relevant regulatory information and symbols. A preview of the 3417 label is shown below: Label Location The ID label is located on the top side of the 3417 RAIN RFID Reader module ID Label ID Label location www.tsl.com 3417 Label Location v1.01Copyright © 2023 Technology Solutions (UK) Ltd 3 About About TSL ® Contact ISO 9001: 2015 ISO 9001 Registered Firm International Accreditation Board Certificate No. GB2001267 Registration No. 0044/1 Technology Solutions UK Ltd (TSL ® ), part of HID Global, is a leading manufacturer of high performance mobile RFID readers used to identify and track products, assets, data or personnel. For over two decades, TSL ® has delivered innovative data capture solutions to Fortune 500 companies around the world using a global network of distributors and system integrators. Specialist in-house teams design all aspects of the finished products and software ecosystems, including electronics, firmware, application development tools, RF design and injection mould tooling. TSL ® is an ISO 9001:2015 certified company. Address:Technology Solutions (UK) Ltd, Suite A, Loughborough Technology Centre, Epinal Way, Loughborough, Leicestershire, LE11 3GE, United Kingdom. Telephone:+44 1509 238248 Fax:+44 1509 214144 Email:[email protected] Website:www.tsl.com Technology Solutions (UK) Ltd reserves the right to change its products, specifications and services at any time without notice. HID Global powers the trusted identities of the world’s people, places and things. We make it possible for people to transact safely, work productively and travel freely. Our trusted identity solutions give people convenient access to physical and digital places and connect things that can be identified, verified and tracked digitally. Millions of people around the world use HID products and services to navigate their everyday lives, and billions of things are connected through HID technology. We work with governments, educational institutions, hospitals, financial institutions, industrial businesses and some of the most innovative companies on the planet. Headquartered in Austin, Texas, HID Global has over 4,000 employees worldwide and operates international offices that support more than 100 countries. HID Global is an ASSA ABLOY Group brand. For more information, visit www.hidglobal.com. About HID Global www.tsl.com

Reference No.: BHTN-WTW-P22110245_INT Page 1/3 CONSTRUCTION PHOTOS OF EUT Reference No.: BHTN-WTW-P22110245_INT Page 2/3 Reference No.: BHTN-WTW-P22110245_INT Page 3/3

Report No.: MFBHTN-WTW-P22110245 Page No. 1 / 5 Report Format Version: 6.1.1 RF Exposure Report Report No.: MFBHTN-WTW-P22110245 FCC ID: S6J-3417 Test Model: 3417 Received Date: Nov. 11, 2022 Test Date: Dec. 07 ~ Dec. 27, 2022 Issued Date: Jan. 30, 2023 Applicant: Technology Solutions (UK) Ltd. Address: Suite A, Loughborough Technology Centre, Epinal Way, Loughborough, Leicestershire, LE11 3GE, UK Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBHTN-WTW-P22110245 Page No. 2 / 5 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result Of Maximum Conducted Power .......................................................................... 5 Report No.: MFBHTN-WTW-P22110245 Page No. 3 / 5 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued MFBHTN-WTW-P22110245 Original release. Jan. 30, 2023 Report No.: MFBHTN-WTW-P22110245 Page No. 4 / 5 Report Format Version: 6.1.1 1 Certificate of Conformity Product: 3417 UHF RAIN RFID Reader Module Brand: TECHNOLOGY SOLUTIONS (UK) LTD Test Model: 3417 Sample Status: Engineering sample Applicant: Technology Solutions (UK) Ltd. Test Date: Dec. 07 ~ Dec. 27, 2022 FCC Rule Part: FCC Part 2 Standards: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Jan. 30, 2023 Polly Chien / Specialist Approved by : , Date:Jan. 30, 2023 Jeremy Lin / Project Engineer Report No.: MFBHTN-WTW-P22110245 Page No. 5 / 5 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 3 Calculation Result Of Maximum Conducted Power Frequency Band (MHz) Max AV Power (dBm) Antenna Gain including cable loss (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 902.75 ~ 927.25 28.30 2.2 20 0.223 0.602 *Antenna Gain: 2.5 dBi – 0.3 dBi = 2.2 dBi Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. ---END---

DATA AND DEVICES / S9025PL/S9025PR FEATURES AND BENEFITS S9025PL/S9025PR Mini RFID Panel Antenna 902-928 MHz S9025PL and S9025PR are high-performance RFID antennas and the only UHF RFID antenna available to the market that offers no-compromise performance in a small package. At only 5.2” square, the antenna offers a gain specification of 5.5 dBic and axial ratio better than 2 dB. In effect, the antenna is providing the performance one would expect of a much larger antenna. The antenna is not only mechanically robust but is less likely to be exposed to excessive damage by virtue of its reduced size. APPLICATIONS •Circularly polarized •Low VSWR and axial ratio •Rugged, ultra-heavy-duty construction • IP67-rated •Left-hand and right-hand CP versions •Weather and UV resistant radome •High performanc e in a small package •Wide range of connector and cable options • Warehouse • Distribution center •Airports and hospitals •Transit terminals •Conveyer belt ELECTRICAL SPECIFICATIONS Antenna ModelS9025PR/S9025PL Operating Frequency (MHz)902 - 928 VSWR – Max1.5:1 Gain (dBic )5.5 Nominal Impedance (Ohms)50 Max Power - Ambient 25°C (W)10 PolarizationCircular RH or Circular LH Horizontal Plane 3 dB Beamwidth100° Front-to-Back Ratio (dB)8 Axial Ratio – Typical (dB)2.0 MECHANICAL SPECIFICATIONS Dimensions – length x width x height – mm (inches)132.1 x 132.1 x 17.8 (5.2 x 5.2 x .71) Weight – kg (lbs.) 0 .37 (0.8) Mounting StyleThreaded Stud 2x #10-32 Radome MaterialWhite High Strength PC Lightning ProtectionDC Grounded Connector TypeType N-Female, RP-TNC Female, RP-SMA-Female, SMA-Female DATA AND DEVICES / S9025PL/S9025PR2 ENVIRONMENTAL SPECIFICATIONS Operating Temperature – °C (°F)-30 to +70°C (-22 to +158°F) Storage Temperature – °C (°F)-40 to +85°C (-40 to +185°F) Impact Resistance1 lb. ball drop, 24” SaltMIL-STD-810 VibrationMIL-STD-810 ShockIEC 68-2-27 HumidityIEC 68-2-27 Ingress Protection RatingIP67 PART NUMBERPOLARIZATIONCONNECTOR S9025PLNFLHCPN Female S9025PLRASMAFLHCPRight Angle, SMA Female S9025PLRTNLHCPRP TNC S9025PLSMFLHCPSMA Female S9025PRNFRHCPN Female S9025PRRASMAFRHCPRight Angle, SMA Female S9025PRRTNRHCPRP TNC S9025PRSMFRHCPSMA Female CONFIGURATION DATA AND DEVICES / S9025PL/S9025PR RADIATION PATTERNS USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico: +52 (0) 55-1106-0800 Latin/S. America: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 TE TECHNICAL SUPPORT CENTER te.com TE, and TE connectivity (logo) are trademarks owned or licensed by the TE Connectivity Ltd. family of companies. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. TE Connectivity warrants to the original end user customer of its products that its products are free from defects in material and workmanship. Subject to conditions and limitations TE Connectivity will, at its option, either repair or replace any part of its products that prove defective because of improper workmanship or materials. This limited warranty is in force for the useful lifetime of the original end product into which the TE Connectivity product is installed. Useful lifetime of the original end product may vary but is not warrantied to exceed one (1) year from the original date of the end product purchase. ©2022 TE Connectivity. All Rights Reserved. 08/22 Original Company Address: 3101 Fulling Mill Rd, Middletown, PA 17057, United States

Report No.: RFBHTN-WTW-P22110245 Page No. 1/ 45Report Format Version: 6.1.1 FCC Test Report Report No.:RFBHTN-WTW-P22110245 FCC ID:S6J-3417 Test Model:3417 Received Date:Nov. 11, 2022 Test Date:Dec. 07 ~ Dec. 27, 2022 Issued Date:Jan. 30, 2023 Applicant:Technology Solutions (UK) Ltd. Address:Suite A, Loughborough Technology Centre, Epinal Way, Loughborough, Leicestershire, LE11 3GE, UK Issued By:Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address:No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location:No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Desi gnation Number:788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBHTN-WTW-P22110245 Page No. 2/ 45Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test ................................................................................................... 11 3.5 General Description of Applied Standards and References .............................................................. 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 29 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 29 4.2.2 Test Instruments .............................................................…

Text truncated - open the document above for the full version.

Reference No.: BHTN-WTW-P22110245_TSup Page No. 1 / 5 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Reference No.: BHTN-WTW-P22110245_TSup Page No. 2 / 5 Radiated Emission Test (Above 1GHz) Reference No.: BHTN-WTW-P22110245_TSup Page No. 3 / 5 Radiated Emission Test (Below 1GHz) Reference No.: BHTN-WTW-P22110245_TSup Page No. 4 / 5 Reference No.: BHTN-WTW-P22110245_TSup Page No. 5 / 5