S6S-SF13PBPOWER BANK

Model: SF13PB 1. Operation instruction 1.1 LED torch using Under fully charged, the energy-saving LED torch will last for above 200 hours. LED torch will be turned off automatically 15 minutes later when it is bright. Power on — Press and hold the button for 2 seconds; Power off—Release the button, and again, press and hold the button for 2 seconds. 1.2 Battery Indicator 1 power indicator and 4 battery level indicators, thus making you can get the power bank’s electricity condition easily. Show as follows: Battery level indicators light 1 indicator and flashing Light 1 indicator Light 2 indicators Light 3 indicators Light 4 indicators SF13PB capacity<15% 15%~25% 25%~50%50%~75% 75%~100% 1.3 Charging Equipped with a Micro double function data line. Charging SF13PB with USB input interface, charging the other devices with output interface. 2. Charging for the other devices SF13PB is used to charge digital communication products with DC-5V input. There is a double function data wire which is compatible to most mobile phone and many other digital communication products. 3. Charging for SF13PB 3.1 Use Micro data wire to charge SF13PB; 3.2 Suggest using adapter for charging, showed as following picture 1; 3.3 Connect USB interface to charge SF13PB is also allowed, showed as following picture 2. Remarks: (1) SF13PB supply with a big capacity, charging time is about 10 hours, also depending on the actual condition. (2) Please check if the wire is normal or not, or if the connection interface stable or not, when you find SF13PB can not be charged. Suggest using duly qualified power adapter for charging. (3) The power bank exist transformation efficiency; therefore, its capacity is not equal with the electricity that chargeable. 4. Charging condition 4.1 Charging other device by SF13PB 4.1.1 If power indicate light is red, means that the device is on charging. 4.1.2 If power indicate light is blue, means that the device has been charged full. 4.1.3 Electricity quantity indicate lights are bright, it shows the remainder power of SF13PB. 4.1.4 When the power quantity is lower than 25%, the SF13PB will remind you to recharge by beep sound at every time you start up the power bank; besides, it also will remind you every half an hour by sound. (This charge remind function can be closed temporarily by double click the power button, when you hear tick sounds like”tick tick tick”, it means that it will be closed. However, the SF13PB will recover the remind function 10 hours later; the remind function will also abolish automatically if the power bank has been charged for more than 25% electricity quantity.) 4.2 When SF13PB on charging condition: 4.2.1 Power indicate light is red, means that SF13PB is on charging condition; 4.2.2 Electricity quantity indicate light twinkle at the relevant position, it shows the current electricity quantity of SF13PB. 4.2.3 Power indicate light is blue, means that SF13PB has been charged full. 5. Connecting with Apple devices with Bluetooth 4.0(e.g. iPhone 4S, iPhone5, new iPad, etc.) SF13PB can connect with Apple intelligent device by low power consumption Bluetooth4.0, thus achieving the functions of loss prevention, theft prevention and searching for each other. 5.1 Bluetooth basic operation of SF13PB. 5.1.1Turning on Bluetooth: pressing power button of SF13PB for 3 seconds, until the device tick for once.(The function only works for Apple devices under pairing status.) 5.1.2 Turning off Bluetooth: pressing power button of SF13PB for 5 seconds, until the device appear sounds like ‘tick-tick tick’. Release the button and quickly double click the button within 10 seconds, Bluetooth will be closed till the device “tick” for once. 5.1.3 Pairing Bluetooth: pressing power button for 10 seconds, until the device ‘tick-tick tick-tick tick tick’, loosen the button and quickly double click the button within 10 seconds, Bluetooth device will get into pairing condition till the device “tick” for once. 5.1.4 Muting: pressing the power button can abolish the alarm when the SF13PB is on warning condition; it will abolish mute condition automatically if power bank get connection with Apple devices again. 5.2 Pairing with Apple device 5.2.1 Software download Download and install “Safeshine Alert” from “App Store” on Apple device. 5.2.2 Paring of SF13PB and Apple device (1) Turn on Bluetooth: Press Home button, tap “Settings” and slide the “Bluetooth” button to turn it on. (2) Run “Safeshine Alert” and tap “Add tag”, the system will start searching for “SF13PB”. (3) Taping the power button for about 10 seconds, The SF13PB will tick for 3 times, sounds like “tick-tick tick-tick tick tick”, then double-click on it, the Apple device will show “SF13PB” which means the SF13PB is ready for pairing. Press ”pair” and then tap “SF13PB”, the appearing screen as below: Press “find tag”, the SF13PB will alarm; press “silence tag”, it will stop. Then, the pairing connection is settled. 5.2.3 Using SF13PB to find Apple device Quickly double-click on power button of SF13PB will begin the search for Apple device, and then Apple device will alarm or make a beep sound. Remarks: when the alarm voice could not be stopped, please double-click the power button of SF13PB, there will be information window, press OK button will stop the alarm. 5.3 Re-pairing setting F5200A may lose connection with its pairing Apple device normally because of miss-operation, those cases will need repairing setting. (One typical miss-operation is to press the power button for a long time and the device gets into the pairing mode, thus making the original pair lose efficacy). It need to delete the original pairing information, operation as follows: 5.3.1 Turn on Bluetooth, tap”forget the device”. ＝〉 5.3.2 Run “Safeshine Alert”, get into configure page, tap “del tag” and select “Yes”: ＝〉 Then, repeat the steps as normal pairing and connection. Remarks: If there are problems that “Safeshine Alert” could not get connection automatically …

Text truncated - open the document above for the full version.

Hangzhou Safeshine Electronics Co., Ltd. Address: Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Tel: 86-0571-86883692 Fax: 86-0571-86883681 2013-11-25 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID:S6S-SF13PB We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics Diagram - Block Diagram - Operation description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : Qianghua Teng/Manager Contact information / address : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Tel: 86-0571-86883692 Fax: 86-0571-86883681

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 4 1.Exterior Photographs of EUT Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 4 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 4 Fig.5 Fig.6 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 4 Fig.7

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 Label and location Size: 3x2.5cm Size:4.5x4.0mm Label And Location POWER BANK Model No.SF13PB FCC ID:S6S-SF13PB This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in china

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1.Interior Photographs of EUT Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.:LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Antenna

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.: LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 38 FCC TEST REPORT For Hangzhou Safeshine Electronics Co., Ltd. POWER BANK Model No.:SF13PB Prepared for : Hangzhou Safeshine Electronics Co., Ltd. Address : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Date of receipt of test sample : November 15, 2013 Number of tested samples : 1 Serial number : Prototype Date of Test : November 15, 2013 - November 25, 2013 Date of Report : November 25, 2013 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.: LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 38 FCC TEST REPORT FCC CFR 47 PART 15 C(15.247): 2012 / RSS-210 Issue 8/RSS-Gen Issue 3 Report Reference No. .............. : LCS131113402TF Date of Issue ................................ : November 25, 2013 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : Hangzhou Safeshine Electronics Co., Ltd. Address ........................................ : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Test Specification Standard ....................................... : FCC CFR 47 PART 15 C(15.247): 2012 / RSS-210 Issue 8/ RSS-Gen Issue 3 Test Report Form No. ................ : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : POWER BANK Trade Mark .................................. : N/A Model/ Type reference ................. : SF13PB Ratings ......................................... : Input: DC 5V/1A;Output:DC 5V/1A;Battery Parameter: DC 3.7V 5200mAh Result ......................................... : Pass Compiled by: Supervised by: Approved by: Jacky Li/ File administrators Fox Zhang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.: LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 38 FCC -- TEST REPORT Test Result: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS131113402TF November 25, 2013 Date of issue Type / Model........................... : SF13PB EUT......................................... : POWER BANK Applicant............................... : Hangzhou Safeshine Electronics Co., Ltd. Address.................................. : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Hangzhou Safeshine Electronics Co., Ltd. Address................................... : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Telephone............................... : / Fax.......................................... : / Factory................................... : Hangzhou Safeshine Electronics Co., Ltd. Address................................... : Dengyun Rd., 518#, Saima Mall, Building1#, Floor 7, Room 702, Hangzhou, China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: S6S-SF13PB Report No.: LCS131113402TF This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 38 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 5 1.3. EXTERNAL I/O ...................................................................................................................................................... 5 1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................... 6 1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................ 6 1.6. MEASUREMENT UNCERTAINTY ...........................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:S6S-SF13PB Report No.:LCS131113402TF _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement (X Position) Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:S6S-SF13PB Report No.:LCS131113402TF _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 1.2. Photo of Line Conducted Emissions Measurement Fig.5